All lessons

Module 44: Solutions and colligative properties · Lesson 44.2 · about 24 min

Solutions and colligative properties: question types and traps

Every way entrance exams ask about solutions: Henry's law, Raoult's law and vapour composition, deviations and azeotropes, colligative properties, molar mass, and van't Hoff factor for dissociation and association, each with a method and its trap. Then practise.

Key points, meanings and formulas on one page: choose "Save as PDF" in the print box.

Chemistry · Class 12 · about 24 minutes. Read Solutions and colligative properties first. Here are the question types, worked examples and practice.

Almost every solutions question is a particle count. Find how many moles of particles are in how much solvent, multiply by the right constant, and remember that ions and dimers change the count.

The question types

1. Concentration conversions. Molality, molarity, mole fraction, with density. Trap: per kg of solvent vs per litre of solution.
2. Henry's law. p = K_H x. Trap: a larger K_H means the gas is less soluble; gas solubility falls with temperature.
3. Raoult's law and vapour composition. p_A = x_A p°_A, y_A = p_A/P. Trap: using x where y is asked; when the vapour is condensed, the new liquid has composition y.
4. Deviations and azeotropes. Match the pair to positive or negative and the sign of ΔH and ΔV. Trap: negative deviation gives a maximum-boiling azeotrope.
5. Relative lowering of vapour pressure. Δp/p° = x₂, or Δp/p = n₂/n₁ for a stronger solution. Trap: it is the solute's mole fraction, not the solvent's.
6. ΔT_b, ΔT_f and molar mass. m = (w₂/M₂)(1000/W₁). Trap: grams of solvent, not of solution; K_f of benzene is 5.12, not 1.86.
7. Osmotic pressure and isotonic solutions. π = iCRT with R = 0.0821 L atm/(mol K). Trap: T in kelvin; compare iC for isotonic.
8. van't Hoff factor. Dissociation, association, abnormal molar mass, degree α. Trap: complex salts like K₄[Fe(CN)₆] give 5 ions, not 11.

Worked examples

Example 1 (level 3, ordering). Arrange by freezing point, highest first: 0.1 m glucose, 0.1 m NaCl, 0.05 m Al₂(SO₄)₃, 0.04 m K₄[Fe(CN)₆] (all fully ionised). Solution. Particle molality i × m: glucose 0.1; NaCl 0.2; Al₂(SO₄)₃ 5 × 0.05 = 0.25; K₄[Fe(CN)₆] 5 × 0.04 = 0.20. Smallest depression freezes highest: glucose > NaCl = K₄[Fe(CN)₆] > Al₂(SO₄)₃.

Example 2 (level 4, degree of association). 2 g of benzoic acid (M = 122) in 25 g of benzene lowers the freezing point by 1.62 K. K_f of benzene = 4.9 K kg/mol. Find the percentage of acid that dimerises. Solution. Expected m = (2/122)/0.025 = 0.656 mol/kg; expected ΔT_f = 4.9 × 0.656 = 3.21 K. i = 1.62/3.21 = 0.504. For dimers, i = 1 − α/2, so α = 2(1 − 0.504) = 0.99, about 99%.

Example 3 (level 4, vapour then liquid). Liquids A (p° = 90 kPa) and B (p° = 30 kPa) form an ideal solution with x_A = 0.25. The vapour is condensed and the liquid allowed to reach equilibrium again. Find the new mole fraction of A in the vapour. Solution. First vapour: p_A = 22.5, p_B = 22.5, y_A = 0.5. The condensed liquid has x_A = 0.5: p_A = 45, p_B = 15, so the new y_A = 0.75. Each step of evaporation and condensation enriches A: this is fractional distillation.

Example 4 (level 5, osmotic pressure of a polymer). 1.0 g of a protein in 100 mL of water gives an osmotic pressure of 0.0025 atm at 27 °C. Find the molar mass. Solution. C = π/RT = 0.0025/(0.0821 × 300) = 1.015 × 10⁻⁴ mol/L. In 0.1 L that is 1.015 × 10⁻⁵ mol, so M = 1.0/1.015 × 10⁻⁵ ≈ 98 500 g/mol. The freezing point depression for the same solution would be about 0.0002 K: far too small to measure, which is why osmotic pressure is used.

“A more concentrated vapour means the liquid becomes richer in the volatile part.” The opposite. The vapour takes away more of the volatile liquid, so the liquid left behind gets richer in the less volatile one, and its boiling point slowly rises during distillation.

Particle molality
i × m: the number that every colligative property follows
Abnormal molar mass
observed M = normal M ÷ i
Physical meaning
The solvent does not care what the particles are, only how many get in its way.

Practise

  • Use molality for ΔT_b and ΔT_f, molarity for π, mole fraction for vapour pressure.
  • y_A = x_A p°_A / P: vapour is richer in the more volatile liquid.
  • Negative deviation: stronger A-B forces, heat out, volume shrinks, maximum-boiling azeotrope.
  • Compare i × m (or i × C), never m alone.
  • Dissociation: i > 1, molar mass looks smaller. Association: i < 1, molar mass looks larger.
  • Osmotic pressure is the method of choice for proteins and polymers.

Check yourself

1Two liquids A (p° = 120 kPa) and B (p° = 40 kPa) form an ideal solution with x_A = 0.5. The mole fraction of A in the vapour is:
2The observed molar mass of NaCl from a freezing point experiment comes out near 30 g/mol. The best explanation is:
3Which pair are isotonic at the same temperature?

Sources

  • JEE Main, JEE Advanced 2026 and NEET (UG) syllabi: Solutions; question patterns studied from published papers (no questions copied)

Your ticks stay in this browser. Save them as a file on the course home.

Updated 2026-11-22. Syllabus and exam patterns follow the official notices checked on 2026-11-22; they can change every year, so check the official exam website. All questions are original fibub work, not copied from past papers or books. Nothing you do here is sent anywhere.