All lessons

Module 8: Rotational motion · Lesson 8.2 · about 30 min

Rotational motion: question types and traps

Every way entrance exams ask about rotation: torque and equilibrium, ladders, moments of inertia and the axis theorems, pulleys with mass, angular momentum conservation, rolling races and friction, sliding balls that start to roll, falling rods and toppling, each with a method and its trap.

Key points, meanings and formulas on one page: choose "Save as PDF" in the print box.

Physics · Class 11 · about 30 minutes. Read the lesson Rotational motion first. Here you meet every question type, with a worked example and the trap, then practise.

Pick the right point to take torques about, and the right quantity to conserve. Hinges, contact points and centres of mass are the usual choices; angular momentum is the quantity whenever friction or a collision acts through that point.

The ten question types

1. Torque and couples. τ = r × F, or force × moment arm. Trap: using the distance to the point of application instead of the perpendicular distance to the line of the force.
2. Equilibrium and ladders. Net force zero in two directions, torques about the foot or top. Trap: a smooth wall gives only a horizontal push.
3. Moment of inertia and theorems. Table values, parallel and perpendicular axes. Trap: the perpendicular axis theorem works only for flat bodies.
4. τ = Iα with pulleys. Block plus massive pulley: a = mg/(m + I/R²). Trap: tension is different on the two sides of a pulley with mass.
5. Angular momentum conservation. Skaters, turntables, people walking on platforms, discs joining. Trap: assuming kinetic energy is kept too.
6. Rolling energy and races. K = ½mv²(1 + k²/R²); order sphere, disc, hollow sphere, ring. Trap: thinking the heavier body wins.
7. Friction in rolling. Static, up the slope, f = mg sin θ/(1 + R²/k²); least μ for pure rolling. Trap: writing f = μN when it rolls without slipping.
8. Rolling with slipping. Angular momentum about the contact point is conserved; final v = v₀/(1 + k²/R²). Time to start rolling from kinetic friction.
9. Rods: falling, hinged, collisions. Energy for ω, τ = Iα for α, angular momentum about the hinge for a bullet hitting a rod.
10. Toppling vs sliding. A block pushed at height h topples if the torque about the front edge beats mg × half-width before friction gives way.

Worked examples

Example 1 (level 3, ladder). A uniform 5 m ladder of weight 200 N leans against a smooth wall with its foot 3 m from the wall. Find the friction at the foot.

Solution. Height of the top = 4 m. Torques about the foot: wall push N_w × 4 = 200 × 1.5, so N_w = 75 N. Horizontal balance: friction = 75 N (towards the wall). The floor push is 200 N, so the ladder needs μ ≥ 0.375.

Example 2 (level 4, pulley with mass). A 2 kg block hangs from a string wound on a 4 kg disc pulley of radius 0.1 m. Find the block’s acceleration and the tension. (g = 10 m/s²)

Solution. a=mgm+M/2=202+2 = 5 m/s². Tension T=m(g−a) = 10 N. Check: TR=Iα=12(4)(0.01)(a/0.1) gives T = 2a = 10 N. ✓

Example 3 (level 4, sliding ball). A solid sphere is thrown along a floor with speed 7 m/s and no spin. μ = 0.2. When does it start rolling, and at what speed? (g = 10 m/s²)

Solution. Final speed = 7/(1 + 2/5) = 5 m/s. Friction slows the centre at μg = 2 m/s², so the time is (7 − 5)/2 = 1 s.

Example 4 (level 5, bullet into a rod). A rod of mass M and length L hangs from a hinge at its top. A bullet of mass m (much less than M) moving horizontally at u hits and sticks at the bottom end. Find the rod’s angular speed just after.

Solution. The hinge pushes during the impact, so linear momentum is not kept. Its torque about the hinge is zero, so take angular momentum about the hinge: muL=(ML23+mL2)ω, so ω=3mu(M+3m)L≈3muML.

“Momentum is conserved when a bullet hits a hinged rod.” The hinge exerts a big force during the impact, so linear momentum changes. Angular momentum about the hinge is the conserved quantity.

Best torque point
the point through which the most unknown forces act (hinge, foot of a ladder, contact point)
Effective mass
a pulley or rolling wheel behaves like extra mass I/R² that must also be speeded up
Physical meaning
Angular momentum about a point is kept whenever every unknown force passes through that point, even if those forces are huge.

Practise

The set climbs from level 1 to level 5 and includes numericals, assertion-reason, statements, matching lists, multi-correct and passage questions. Templates give new numbers each time.

  • Ten types: torque, ladders, moment of inertia, pulleys, L conservation, rolling races, friction in rolling, rolling with slipping, rods, toppling.
  • Take torques about the point that removes the most unknowns.
  • Massive pulley: a = mg/(m + I/R²); tensions differ on its two sides.
  • Sliding sphere: final speed 5v₀/7, from angular momentum about the contact point.
  • Bullet into a hinged rod: angular momentum about the hinge, not linear momentum.

Check yourself

1The moment of inertia of a thin uniform rod of mass M and length L about an axis through one end, perpendicular to the rod, is:
2A disc spinning at ω is gently placed on an identical disc at rest on the same axis. They end up spinning together at:
3For a solid cylinder rolling without slipping, the fraction of its kinetic energy that is rotational is:

Sources

  • JEE Main, JEE Advanced 2026 and NEET (UG) syllabi: Rotational motion; question patterns studied from the exams' published papers (no questions copied)

Your ticks stay in this browser. Save them as a file on the course home.

Updated 2026-11-22. Syllabus and exam patterns follow the official notices checked on 2026-11-22; they can change every year, so check the official exam website. All questions are original fibub work, not copied from past papers or books. Nothing you do here is sent anywhere.