Home / Learn / Exam prep / IIT JAM Physics / Lesson 4.6
All lessons

Module 4: Electricity and magnetism · Lesson 4.6 · about 45 min

Magnetic materials: B, H and M

Magnetisation and bound currents, the H field and Ampère's law for free current, B = μ0(H + M), susceptibility and permeability, dia-, para- and ferromagnetism, the Curie and Curie-Weiss laws, hysteresis, boundary conditions, magnetised spheres and rods, and magnetic circuits with air gaps.

Key points, meanings and formulas on one page: choose "Save as PDF" in the print box.

Module 4 · about 45 minutes. By the end you will be able to turn a magnetisation into bound currents, use H→ and Ampère’s law with free current only, tell dia-, para- and ferromagnets apart by their susceptibility, read a hysteresis loop, apply the boundary conditions, and design an electromagnet with an air gap.

Every atom is a tiny current loop; when a field lines them up, their currents cancel inside the material but not at its surface, and that surface current is what makes iron multiply a magnetic field a thousand times.

1. Magnetisation and bound currents

Electrons orbiting and spinning give atoms magnetic moments. In a field they line up (or, in diamagnets, an opposing moment is induced). The magnetisation M→ is the magnetic moment per unit volume, in A/m.

A magnetised material acts like two sets of current:

J→b=∇×M→  (inside),K→b=M→×nˆ  (on the surface)

Picture uniform M→ as a grid of identical little loops: neighbouring loops carry opposite currents along their shared edges and cancel, leaving only the current round the outside edge. A rod magnetised along its axis is therefore a solenoid with nI=M: B=μ0M inside. With M=8×105 A/m (typical iron), that is 1 T, and a 10 cm rod carries a bound current of 80 kA round its side. No wire could do that without melting; this is why permanent magnets are so convenient.

Worked example. M→=ksϕˆ in a long cylinder: J→b=1sdds(ks2)zˆ=2kzˆ, and on the surface K→b=M→×sˆ=−kRzˆ. The two exactly cancel in total, as bound currents must across any cross-section.

2. The H field

The magnetic field comes from all currents, free and bound. Define

H→=B→μ0−M→,∇×H→=J→f,∮H→⋅dl→=If,enc

so Ampère’s law for H→ needs only the free current in the wires. In a linear material M→=χmH→, so B→=μ0(1+χm)H→=μH→ with μr=1+χm.

Worked example. A solenoid with 1000 turns/m carrying 2.0 A: H=nI=2000 A/m whatever the core. With soft iron of μr=500, B=μ0μrH=1.26 T, five hundred times the empty value.

M
how strongly the material is magnetised: magnetic moment per cubic metre (A/m)
J_b, K_b
the leftover edges of all the atomic current loops; real currents, but bound to atoms
H
a field whose curl is the free current only; set by the wires you wind, in A/m
B = μ₀(H + M)
the actual field, which exerts forces and whose flux induces EMFs
Physical meaning
H is what you apply with your coils; M is how the material answers; B is the sum of both and is what a compass or a moving charge feels.

“H points the same way as B, just smaller.” Inside a permanent magnet it does not. With no free current ∮H→⋅dl→=0: outside, H→ runs from N to S, so inside it must run N to S as well, against M→. B→ makes closed loops and runs S to N inside. H→ lines start and end on the poles, like electric field lines on charges.

3. Three kinds of magnetism

Kind χm Temperature Origin
Diamagnetic (Cu, water, Bi) about −10−5 nearly none orbits respond to the field by Lenz’s law; present in all matter
Paramagnetic (Al, O₂, salts) +10−5 to 10−3 Curie: χ=C/T permanent moments partly aligned against thermal agitation
Ferromagnetic (Fe, Co, Ni) up to 105, not constant ordered below Tc, Curie-Weiss above exchange forces align neighbours into domains
Superconductor (Meissner) exactly −1 below Tc surface supercurrents expel B→

Diamagnets are pushed out of strong fields, paramagnets pulled in. Curie’s law comes from moments μ in field B: alignment needs μB to compete with kBT, giving χ=μ0Nμ23kBT for moments free to point anywhere. For spin-½ moments of one Bohr magneton in 1 T at 300 K, the excess pointing along the field is tanh⁡(μBB/kBT)≈2×10−3: only two in a thousand.

Ferromagnets. Weiss’s idea: each moment feels an extra field λM from its neighbours. Then M=(C/T)(H+λM) gives the Curie-Weiss law χ=CT−Tc with Tc=λC; below Tc the material magnetises spontaneously in domains. Iron fully aligned has Ms=N⋅2.2μB≈1.7×106 A/m, so μ0Ms≈2.2 T.

4. Hysteresis

Drive a ferromagnet with a coil and sweep H up and down. Domains grow and shrink with friction, so B does not retrace its path:

A B-H loop traced as H sweeps back and forth. Slide the coercivity from soft (thin loop, transformer cores) to hard (wide loop, permanent magnets). The shaded area is the energy lost as heat in every cycle.
  • Remanence Br: the field left when H returns to zero.
  • Coercivity Hc: the reverse H needed to bring B to zero.
  • Loop area ∮HdB: energy turned to heat per unit volume per cycle. A core with loop area 300 J/m³ and volume 1 litre, run at 50 Hz, wastes 15 W.

Soft materials (small Hc, thin loops) suit transformers and electromagnets; hard materials (large Hc) make permanent magnets, which must resist their own demagnetising field.

5. Boundary conditions and shapes

At a boundary with no free surface current:

B1⟂=B2⟂,H1∥=H2∥

(the magnetic mirror of the dielectric rules, with B→ as D→ and H→ as E→). Lines bend as tan⁡θ2tan⁡θ1=μ2μ1: entering iron with μr=1000 at 45∘, they run almost along the surface, and leaving iron they come out almost perpendicular to it.

Shape matters.

  • Long rod magnetised along its axis: B=μ0M, H=0.
  • Uniformly magnetised sphere: B→in=23μ0M→, H→in=−13M→; outside, exactly a dipole of moment 43πR3M→. Just outside, B is 23μ0M at the poles (matching B⟂) but 13μ0M (reversed) at the equator.
  • Linear sphere in a uniform B0: Bin=3μrμr+2B0, so even μr→∞ only triples it.
  • A wire on the axis of a linear cylinder: H=I/2πs from the free current, B=μ0(1+χm)I/2πs inside the material.

Worked example. M=1.0×105 A/m in a sphere: Bin=23(1.2566×10−6)(105)=83.8 mT, and Hin=−3.3×104 A/m.

6. Magnetic circuits

Iron guides flux the way copper guides current. Round a core of path l with a gap g (same B in both, neglecting fringing), Ampère’s law for H→ gives

Bμ0μrl+Bμ0g=NI⇒B=μ0NIl/μr+g

Each term is a reluctance (flux “resistance”) in series. With μr=2000, l=0.50 m and a 1.0 mm gap, the iron counts as 0.25 mm of air, so the gap dominates: 200 turns at 1.0 A give B=(1.2566×10−6)(200)1.25×10−3=0.201 T. The pull of an electromagnet on an iron plate across a thin gap is B2A2μ0: the field’s energy density acts as a pressure.

A ring of permanent magnet with fixed M and a small gap: no free current, so Hm(l−g)+Hgg=0, which gives B=μ0M(l−g)/l in the gap, slightly less than μ0M. The magnetic circuit solver works out reluctance, flux and inductance for cores of iron or ferrite with gaps, and the coil field designer does air-cored coils.

  • J→b=∇×M→, K→b=M→×nˆ. Uniformly magnetised rod = solenoid with nI=M.
  • H→=B→/μ0−M→, ∮H→⋅dl→=If; linear: B→=μ0μrH→, μr=1+χm.
  • Dia: χ≈−10−5, T-independent. Para: χ=C/T. Ferro: hysteresis, domains, χ=C/(T−Tc) above Tc. Superconductor: χ=−1.
  • Hysteresis: remanence at H=0, coercivity at B=0, loop area = heat per volume per cycle. Soft for transformers, hard for magnets.
  • Boundaries: B⟂, H∥ continuous. Sphere: Bin=23μ0M, Hin=−13M; rod: B=μ0M, H=0.
  • Magnetic circuit: B=μ0NI/(l/μr+g); the gap usually dominates. Holding force B2A/2μ0.

Practise: exam questions on this lesson

These start easy and climb to top-rank level. Check each answer, then read the full solution. More on the magnetic materials practice page.

Next: electromagnetic induction and inductance, where iron cores raise inductances by μr. The electric twin of this lesson is dielectrics and capacitors; the fields of the free currents came from Biot-Savart and Ampère. For the quantum theory of magnetism at MSc level, see the GATE Physics course.

Check yourself

1A long rod is uniformly magnetised along its length, with no free current anywhere. Far from its ends, what are B and H inside?
2A paramagnet obeys Curie's law. Its absolute temperature is doubled. What happens to its susceptibility?
3An iron electromagnet has a 1 mm air gap. Which part sets the current needed for a given gap field?

Sources

  • D. J. Griffiths, Introduction to Electrodynamics, 4th ed. (2017), chapter 6: magnetic fields in matter
  • E. M. Purcell and D. J. Morin, Electricity and Magnetism, 3rd ed. (2013), chapter 11
  • C. Kittel, Introduction to Solid State Physics, 8th ed. (2005), chapters 11 and 12 (para- and ferromagnetism)
  • IIT JAM Physics syllabus (Electricity and Magnetism section), published by the organising IIT each year

Your ticks stay in this browser. Save them as a file on the course home.

Updated 2026-11-22. Not affiliated with IIT or the JAM organising institute. Exam pattern as published for recent years: always check the official JAM website before the exam. All questions are original.