Home / Learn / Exam prep / IIT JAM Physics / Lesson 2.7
All lessons

Module 2: Mechanics and properties of matter · Lesson 2.7 · about 40 min

Elasticity: stress, strain and the elastic constants

Stress, strain and Hooke's law; Young's, bulk and shear moduli and Poisson's ratio and how they are linked; the stress-strain curve; elastic energy; thermal stress; wires under their own weight; torsion of wires and the torsion pendulum; bending of cantilevers.

Key points, meanings and formulas on one page: choose "Save as PDF" in the print box.

Module 2 · about 40 minutes. By the end you will be able to work out the stretch, twist or sag of a loaded body, move between Young’s modulus, the bulk and shear moduli and Poisson’s ratio, read a stress-strain curve, and find the energy stored in a deformed solid.

For small deformations a solid behaves like a very stiff spring whose stiffness belongs to the material, and three numbers (or any two of them for an isotropic solid) describe every way it can be stretched, squeezed or twisted.

1. Stress, strain and Hooke’s law

Pull a wire with force F and it stretches. How much depends on the wire’s size, so we divide the size out:

  • stress = force per unit area, F/A (pascals);
  • strain = fractional change, ΔL/L (no units).

Within the proportional limit, stress is proportional to strain (Hooke’s law), and the ratio is a property of the material alone:

Y=F/AΔL/L⇒ΔL=FLAY,k=YAL

A long, thin wire is a soft spring; a short, thick one a stiff spring; but both have the same Y. Physicists call steel “more elastic” than rubber because it needs a much larger stress per unit strain.

Worked example. A steel wire (Y=2×1011 Pa) 2 m long with cross-section 1 mm² carries 100 N: ΔL=100×210−6×2×1011=1 mm. Watch the units: 1 mm² = 10−6 m².

2. Three ways to deform, three moduli

Deformation Stress Strain Modulus
Stretch F/A along the length ΔL/L Young’s modulus Y
Squeeze from all sides pressure Δp −ΔV/V bulk modulus K (compressibility 1/K)
Shear (slide the top face) tangential F/A angle of shear ϕ shear (rigidity) modulus G or η

A stretched wire also gets thinner. Poisson’s ratio σ = (lateral strain)/(longitudinal strain), taken as positive. The volume of a stretched wire changes by ΔV/V=(1−2σ)ΔL/L.

Liquids and gases have a bulk modulus but no shear modulus: a steady shear just makes them flow. For an ideal gas the isothermal bulk modulus is p and the adiabatic one γp.

Y
resistance to stretching: stress needed per unit fractional stretch
K
resistance to squeezing from all sides; infinite for an incompressible material
G
resistance to change of shape at constant volume; zero for a fluid
σ
how much it thins when stretched; σ = 1/2 means the volume stays the same
Physical meaning
The moduli measure how stiff the springs between atoms are, in three different patterns of pushing. Big modulus, small deformation.

3. How the constants are linked

For an isotropic solid only two constants are independent. Step through where the shear relation comes from:

Shear is two stretches. A small square sheared by angle φ has one diagonal stretched by strain φ/2 and the other squeezed by φ/2.

The stresses on the diagonals. A shear stress S on the faces is the same as a tension S along one diagonal plus a compression S along the other.

Strain along the stretched diagonal. From its own tension: S/Y. From the compression across it (Poisson): σS/Y. Total (1 + σ)S/Y.

Equate. φ/2 = (1 + σ)S/Y and G = S/φ give Y = 2G(1 + σ).

Y=2G(1+σ)=3K(1−2σ),9Y=1K+3G,−1<σ<12

The limits come from K>0 and G>0. Most metals have σ≈0.3, rubber nearly 0.5, cork nearly 0; some engineered foams are negative (they fatten when stretched).

Worked example. Y=2.1×1011 Pa, σ=0.3: G=2.1×1011/2.6=81 GPa and K=2.1×1011/(3×0.4)=175 GPa.

4. The stress-strain curve

A sketch of a ductile metal (and, at the switch, a brittle solid) pulled until it breaks. Past the elastic limit, unloading follows a line parallel to the Hooke's law line and leaves a permanent stretch.

Reading the curve of a ductile metal from the origin: the straight Hooke’s law region (slope Y) up to the proportional limit; the elastic limit, beyond which a permanent set remains; yield, where planes of atoms slip; strain hardening up to the ultimate tensile strength (the highest point); then necking and fracture. A brittle solid (glass, cast iron) follows a straight line almost to fracture. The breaking load is Sbreak×A, so it depends on the area, not the length. A loop between loading and unloading curves (elastic hysteresis, strong in rubber) encloses the energy turned into heat per unit volume.

5. Elastic energy, thermal stress and self-weight

Stretching a wire takes work 12FΔL because the force grows from zero. Per unit volume:

u=12stress×strain=12Yε2=stress22Y
  • Thermal stress: a bar clamped between walls and warmed by ΔT would expand by strain αΔT; the walls push back with stress YαΔT, whatever its length.
  • Own weight: a hanging wire stretches by ρgL2/2Y, the same as a weightless wire carrying half its weight. The area cancels.
  • Sudden loads: a weight hung on and let go stretches a wire to twice the static extension for an instant.

Worked example. A steel rail (α=1.2×10−5 K⁻¹) clamped and warmed by 50 K: stress =2×1011×1.2×10−5×50=120 MPa, which is why rails have expansion gaps.

“A thicker wire under the same load stores more energy because there is more metal.” It stores less. Energy 12FΔL=F2L/(2AY) falls as the area grows, because the thick wire stretches less. For the same stress, though, energy per unit volume is the same, and the bigger wire stores more in total. Always ask what is being held fixed.

6. Twisting and bending

Torsion. Twist the free end of a wire (radius r, length L) through angle φ. A thin shell of radius s is sheared by sφ/L; adding up the torques of all the shells:

τ=πGr42Lφ=cφ,Ttorsion pendulum=2πIc

The r4 means the outer metal does almost all the work, so a hollow shaft is stiffer than a solid one of the same mass and length. A torsion pendulum (a disc on a wire) measures G from its period.

Bending. A cantilever of length L with load W at the free end sags by

δ=WL33YIg,Ig=bd312 (rectangular section, width b, depth d)

The depth enters cubed: a plank on edge is far stiffer than the same plank lying flat, which is why floor joists stand on edge and girders are I-shaped. For real beams and columns, try the beam deflection calculator and the column buckling calculator.

Worked example. A steel strip 2 cm wide and 0.5 cm thick, clamped flat as a 0.5 m cantilever with 10 N at the end: Ig=0.02×0.0053/12=2.08×10−10 m⁴ and δ=10×0.1253×2×1011×2.08×10−10=1.0 cm.

  • Stress F/A, strain ΔL/L; Y= stress/strain; ΔL=FL/AY.
  • Bulk modulus K=−Vdp/dV (gas: p isothermal, γp adiabatic); shear modulus G= shear stress/shear angle; fluids have G=0.
  • Y=2G(1+σ)=3K(1−2σ), 9/Y=1/K+3/G, −1<σ<1/2; volume strain (1−2σ)ε.
  • Stress-strain: proportional limit, elastic limit, yield, ultimate strength, necking, fracture; breaking load ∝A.
  • Energy per volume 12 stress × strain; thermal stress YαΔT; self-weight stretch ρgL2/2Y.
  • Torsion τ=(πGr4/2L)φ; cantilever sag WL3/3YIg, Ig=bd3/12.

Practise: exam questions on this lesson

They start easy and climb to top-rank level. More on the elasticity practice page.

Before this: lesson 2.6, rotation, rolling and angular momentum. Next: lesson 2.8, fluids, the materials with no shear modulus at all.

Go deeper: stress and strain are the first tensors most students meet; GATE Physics treats them in general in tensors, and CSIR NET’s defects and dislocations explains why real metals yield far below their ideal strength.

Check yourself

1Two wires of the same metal carry the same load. Wire B is twice as long as A and has twice its diameter. How does B's extension compare with A's?
2Which value of Poisson's ratio describes a material whose volume does not change when it is stretched slightly?
3The torsion constant of a wire (torque per unit twist) depends on its radius r as

Sources

  • D. S. Mathur, Elements of Properties of Matter (S. Chand), chapters on elasticity
  • C. Kittel, W. D. Knight and M. A. Ruderman, Mechanics, Berkeley Physics Course vol. 1, 2nd ed. (1973), chapter on elasticity
  • L. D. Landau and E. M. Lifshitz, Theory of Elasticity, 3rd ed. (1986), chapter 1, for the relations between the constants
  • IIT JAM Physics syllabus (Mechanics and General Properties of Matter), published by the organising IIT each year

Your ticks stay in this browser. Save them as a file on the course home.

Updated 2026-11-22. Not affiliated with IIT or the JAM organising institute. Exam pattern as published for recent years: always check the official JAM website before the exam. All questions are original.