All lessons

Module 31: Experimental skills and practical physics · Lesson 31.1 · about 34 min

Experimental skills and practical physics

Every practical in the JEE and NEET syllabus: vernier, screw gauge and least count, error and significant figures in results, the pendulum, Young's modulus, capillary rise, viscosity, specific heat, resonance tube, metre bridge, Ohm's law, galvanometer, mirrors, lenses and prisms, the travelling microscope, and diode and Zener characteristics, with the graph to draw and the main error in each.

Key points, meanings and formulas on one page: choose "Save as PDF" in the print box.

Physics · Class 12 · about 34 minutes. By the end you will know, for every experiment in the syllabus, what is measured, the formula used, the graph to draw and the main source of error, and you will be able to read a screw gauge with a zero error.

An experiment is a formula plus a measurement plan. Know which quantity is hardest to measure precisely (it dominates the error), which graph turns the formula into a straight line, and which correction removes a fixed mistake. Exams test exactly those three things.

1. Measuring lengths

The lesson Units and measurements covers the vernier caliper, significant figures and error rules in detail. Here is the screw gauge.

  • Least count of a screw gauge = pitch / number of circular divisions. Pitch is the distance the spindle moves in one full turn.
  • Reading = main scale reading (MSR) + circular scale reading (CSR) × least count.
  • Zero error: if, with the jaws closed, the circular scale’s zero is below the reference line, the error is positive; above, negative. True value = reading − zero error (with its sign).
  • Backlash error: a loose screw gives a different reading when turned back; always turn in one direction, using the ratchet.
A screw gauge with pitch 0.5 mm and 50 circular divisions (least count 0.01 mm). Read the last visible mark on the sleeve, then the circular division on the reference line, and subtract any zero error.

2. Mechanics and properties of matter

Experiment Formula Graph and key error
Simple pendulum T=2πL/g T² against L, slope 4π²/g; L is to the bob’s centre; time 20 or more swings; small angles
Young’s modulus (Searle) Y=MgLπr2Δl load against extension; the radius (squared) and the tiny Δl dominate the error
Surface tension (capillary) T=rhρg2cos⁡θ radius r needs a travelling microscope; clean tube
Viscosity (falling ball) η=2r2(ρ−σ)g9vt measure v_t only after the ball stops speeding up; wall effects
Specific heat (mixtures) heat lost = heat gained heat loss to the room; transfer quickly

Error in a result. For Y=MgLπr2Δl, the fractional error is ΔMM+ΔLL+2Δrr+Δ(Δl)Δl. The quantity with the largest fractional error should be measured most carefully, and a power doubles its share.

3. Sound and heat

Resonance tube. A tuning fork over a tube of air closed at the bottom by water gives loud resonance at lengths l₁ and l₂:

l1+e=λ4,l2+e=3λ4,v=2f(l2−l1),e=l2−3l12≈0.3d

The end correction e accounts for the air just above the open end vibrating too; d is the tube’s inner diameter. Using the difference l₂ − l₁ removes e from v.

4. Electricity

Metre bridge
X = S l/(100 − l); swap X and S and average to cancel end resistance; best balance near the middle
Resistivity
ρ = XA/L = Xπd²/(4L); the diameter, squared, dominates the error
Ohm's law
V against I is a straight line, slope R; keep the current small so the wire does not heat
Galvanometer (half deflection)
G = RS/(R − S), with R in series and S the shunt that halves the deflection; for R much larger than S, G ≈ S
Physical meaning
Bridge methods measure resistance at balance, when no current flows through the detector, so the detector's own resistance and sensitivity drop out of the answer.

Diode and Zener characteristics. For a p-n junction diode, forward current stays tiny until about 0.7 V (silicon), then rises steeply; reverse current is microamperes. A Zener in reverse shows a sharp breakdown at V_z where the voltage stays nearly fixed. Use a milliammeter for the forward curve and a microammeter for the reverse curve.

“More readings always reduce every error.” Repeating a measurement reduces random errors only. A systematic error, such as a zero error, a wrong scale or a constant end correction, is the same every time; averaging cannot remove it. You must correct it, or design it away (two-point slopes, swapping positions).

5. Optics

  • Concave mirror and convex lens (u-v method): find v for several u; plot 1/v against 1/u (a straight line with both intercepts 1/f), or u + v against uv. Check with the u = v = 2f point.
  • Convex lens by parallax: move a pin until its image and the pin show no relative movement as you move your eye: no parallax means same position.
  • Prism (i-δ curve): deviation falls, reaches a minimum δ_m, then rises; at minimum the ray passes symmetrically and μ=sin⁡A+δm2sin⁡A2.
  • Refractive index of a slab (travelling microscope): read a mark directly (R₁), through the slab (R₂), and the slab’s top surface (R₃): μ=R3−R1R3−R2 = real thickness / apparent thickness.
1. Identify the formula. Every practical answer starts from one formula you already know from theory.
2. Make it straight. Choose the axes so the formula becomes y = mx + c: T² vs L, 1/v vs 1/u, V vs I.
3. Find the dominant error. The smallest measured quantity, or the one raised to the highest power.
4. Remove fixed errors. Zero errors, end corrections and end resistances by subtraction, two-point slopes or swapping.
5. Report sensibly. Round the result to match the least precise measurement and quote the error to one or two significant figures.

Worked example (level 4). In Searle’s experiment, L = 2.000 m, wire diameter 0.50 mm (least count 0.01 mm), load 4.0 kg, extension 2.00 mm (least count 0.01 mm). Y = (4 × 9.8 × 2)/(π × (0.25 × 10⁻³)² × 2.00 × 10⁻³) ≈ 2.0 × 10¹¹ Pa. Error: 2 × (0.01/0.50) + 0.01/2.00 = 4% + 0.5% = 4.5% (ignoring the small errors in M and L). The diameter, not the extension, is the weakest link.

  • Screw gauge LC = pitch/divisions; true reading = observed − zero error; zero below the line is positive.
  • Pendulum: T² vs L, slope 4π²/g. Searle: error dominated by 2Δr/r.
  • Capillary T = rhρg/(2 cos θ); viscosity η = 2r²(ρ − σ)g/(9v_t).
  • Resonance tube v = 2f(l₂ − l₁); end correction e = (l₂ − 3l₁)/2 ≈ 0.3d.
  • Metre bridge X = S l/(100 − l), swap to remove end errors; ρ = Xπd²/4L.
  • Half deflection G = RS/(R − S).
  • u-v graphs for f; i-δ curve for μ; travelling microscope μ = real/apparent thickness.
  • Averaging cuts random error only; correct systematic errors.

Check yourself

1A screw gauge has pitch 0.5 mm and 50 circular divisions. Its least count is:
2In the resonance tube experiment, the first two resonance lengths are 16 cm and 50 cm. The end correction is:
3To find g from a pendulum, the best graph to plot is:

Sources

  • National Medical Commission NEET (UG) syllabus and JEE Main / JEE Advanced 2026 syllabi: Experimental skills
  • Speed of sound in air about 343 m/s at 20 °C (rises about 0.6 m/s per °C): NPL (UK) acoustics guidance https://www.npl.co.uk

Your ticks stay in this browser. Save them as a file on the course home.

Updated 2026-11-22. Syllabus and exam pattern follow the official NMC and NTA notices checked on 2026-11-22; they can change every year, so check neet.nta.nic.in. All questions are original fibub work, not copied from past papers or books. Nothing you do here is sent anywhere.