Home / Learn / Exam prep / GATE Physics / Lesson 3.8
All lessons

Module 3: Electromagnetic theory · Lesson 3.8 · about 60 min

Waveguides

Guided waves in hollow metal pipes: TE and TM modes of a rectangular guide, cutoff frequencies and the dominant TE10 mode, guide wavelength, phase and group velocity, wave impedance, evanescent modes and power flow; the bouncing plane-wave picture; circular guides; TEM lines and transmission-line basics; cavity resonators; and step-index optical fibres.

Key points, meanings and formulas on one page: choose "Save as PDF" in the print box.

Module 3 · about 60 minutes. By the end you will be able to find the modes and cutoff frequencies of rectangular and circular guides, say which modes propagate at a given frequency, compute guide wavelength, phase and group velocities, wave impedance, attenuation below cutoff and carried power, picture modes as bouncing plane waves, and apply the same ideas to coaxial lines, cavity resonators and optical fibres. It builds on lesson 3.7: a guided mode is a wave reflected back and forth between walls.

Walls force the field into standing waves across the guide. Each standing pattern costs a fixed transverse wavenumber, so the wave can travel along the guide only if its frequency is high enough to pay that cost: every mode has a cutoff.

1. Guided waves: the general recipe

Take a perfectly conducting hollow pipe along z, filled with a medium of wave speed v=1/μϵ. Look for fields ∝ei(kzz−ωt). The longitudinal components Ez and Bz each obey the 2D Helmholtz equation in the cross-section,

(∂x2+∂y2+kc2){Ez,Bz}=0,kc2=ω2v2−kz2

and every transverse component follows from them by differentiation. The walls set the boundary conditions: Ez=0 (tangential E vanishes) and ∂Bz/∂n=0 (normal B vanishes). Three families:

  • TE (Ez=0, Bz≠0) and TM (Bz=0, Ez≠0). Each has a discrete set of kc values.
  • TEM (Ez=Bz=0): needs kc=0, and then the transverse field is a 2D electrostatic field. Inside one closed conductor that field is zero, so hollow guides have no TEM mode. Two conductors (coax, parallel plates, a twisted pair) allow it, with no cutoff.

From kc2=ω2/v2−kz2, a mode propagates only above its cutoff ωc=vkc:

ω2=ωc2+v2kz2

the same form as the cold plasma of lesson 3.6. Hence, with s=1−(fc/f)2:

λg=λs,vp=vs>v,vg=vs<v,vpvg=v2

Below cutoff kz=iα with α=kc2−k2: an evanescent mode, decaying without travelling.

2. The rectangular guide

For a guide 0≤x≤a, 0≤y≤b with a>b, separation of variables gives

Bz∝cos⁡mπxacos⁡nπyb (TEmn),Ez∝sin⁡mπxasin⁡nπyb (TMmn)
fc,mn=v2(ma)2+(nb)2

TE allows one index to be zero; TM needs both at least 1 (otherwise Ez≡0 and nothing is left). So:

  • The dominant mode is TE₁₀, with fc=v/2a and cutoff wavelength 2a: half a wavelength must fit across the broad side.
  • Its field: Ey∝sin⁡(πx/a), uniform in y, largest in the middle and zero at the side walls; Bx∝sin⁡(πx/a) and Bz∝cos⁡(πx/a).
  • The next modes are TE₂₀ (v/a) and TE₀₁ (v/2b). Choosing a≈2b makes them coincide and gives a single-mode band of a full factor 2 in frequency. TE and TM with the same m,n≥1 always share a cutoff.

Worked example. An air guide 2.5 cm × 1.0 cm: TE₁₀ at 6.0 GHz, TE₂₀ at 12.0, TE₀₁ at 15.0, TE₁₁/TM₁₁ at 16.2 GHz. Single-mode operation runs from 6 to 12 GHz. At 9.0 GHz, s=1−(6/9)2=0.745: λg=3.33/0.745=4.47 cm, vg=0.745c and vp=1.34c. At 20 GHz eight modes propagate.

Top: the cutoff ladder for a guide of aspect ratio b/a; modes to the left of the operating frequency propagate. Bottom: the transverse electric field of the chosen mode in the cross-section.

Wave impedance and power. The ratio of transverse E to transverse H is

ZTE=ηs,ZTM=ηs

ZTE rises without limit and ZTM falls to zero at cutoff; both tend to η far above it. For TE₁₀ with peak field E0, integrating the Poynting vector over the cross-section gives P=E02ab4ZTE. With air breaking down near 3 MV/m, the 2.5 × 1.0 cm guide at 9 GHz carries at most about 1.1 MW.

Below cutoff. At 3 GHz in the same guide, α=(π/a)2−k2=109 Np/m: 47 dB over 5 cm. Far below cutoff α≈π/a hardly depends on frequency, which makes below-cutoff attenuators precise, and is why a microwave oven door’s small holes block 2.45 GHz while letting light through.

3. The bouncing plane-wave picture

TE₁₀ is two plane waves zigzagging between the side walls at angle θ to the axis. Their sum must vanish at x=0 and x=a, so ksin⁡θ=π/a:

sin⁡θ=λ2a=fcf,kz=kcos⁡θ,vg=ccos⁡θ,vp=ccos⁡θ

At cutoff θ=90∘: the waves bounce straight across and get nowhere. Far above cutoff they travel almost along the axis. Energy moves along the zigzag at c, so its axial speed is ccos⁡θ; the phase velocity is just how fast the crossing point of a slanted wavefront slides along the wall.

“The phase velocity in a waveguide exceeds c, so signals do too.” Signals and energy travel at the group velocity, c1−(fc/f)2, always below c. The phase velocity is the speed of a pattern, like the point where a wave breaks along a beach, which can run faster than any water. A 9 GHz pulse needs 44.7 ns for 10 m of the guide above, against 33.4 ns in free space.

4. Circular guides, TEM lines and transmission lines

Circular guide (radius R): the modes involve Bessel functions. TM modes use zeros of Jn, TE modes zeros of Jn′: fc=vx2πR with x = 1.841 (TE₁₁, dominant), 2.405 (TM₀₁), 3.054 (TE₂₁), 3.832 (TE₀₁ and TM₁₁, degenerate because J0′=−J1). The single-mode band is only a factor 1.31 wide. A 1.0 cm radius air guide has TE₁₁ cutoff 8.78 GHz.

Coaxial line (radii a<b): TEM with v=c/ϵr at every frequency (no dispersion) and

Z0=L′C′=η02πϵrln⁡ba

b/a=3.6 with polyethylene gives 51 Ω. Above roughly λc≈π(a+b)ϵr a TE₁₁ mode appears, which sets a cable’s upper frequency.

Transmission-line basics. A load ZL on a line of impedance Z0 reflects Γ=ZL−Z0ZL+Z0, making a standing wave with VSWR=1+|Γ|1−|Γ| (75 Ω on 50 Ω: Γ=0.2, VSWR 1.5, 4% of the power back). A line a quarter wavelength long transforms ZL into Z02/ZL; that is how a quarter-wave section matches two impedances, the same physics as an antireflection coating.

5. Cavities and optical fibres

Cavity resonators. Close a rectangular guide at both ends (length d) and the field must form a standing wave along z too:

fmnp=v2(ma)2+(nb)2+(pd)2

Index sets with all three non-zero carry two modes (TE and TM), those with one zero carry one. A 2.5 × 1.0 × 5.0 cm box has its TE₁₀₁ resonance at 6.70 GHz. The quality factor from wall loss is roughly Q∼V/(Sδ) (stored volume over lossy skin volume), around 104 for copper at microwave frequencies; better conductors and smoother walls raise it.

Step-index optical fibres are dielectric waveguides that guide by total internal reflection. Core n1, cladding n2:

NA=n12−n22=sin⁡θa,V=2πaλNA

The fibre is single-mode for V<2.405 (the first zero of J0, again); for large V it carries about V2/2 modes. Worked example. Core radius 4.0 μm, NA 0.12, at 1.31 μm: V=2.30, single-mode. In a multimode step-index fibre, ray optics gives an intermodal delay spread Δt=Ln1c(n1n2−1): 68 ns per km for n1=1.50, n2=1.48, which limits the bit rate. Single-mode fibre removes it and leaves only material and waveguide dispersion.

f_c = (v/2)√((m/a)² + (n/b)²)
cutoff of the TE or TM (m, n) mode of a rectangular guide
s = √(1 − (f_c/f)²)
the one factor behind λ_g = λ/s, v_p = v/s, v_g = vs, Z_TE = η/s, Z_TM = ηs
α = √(k_c² − k²)
decay constant of a mode below cutoff
V = (2πa/λ)NA
normalised frequency of a fibre; single-mode below 2.405
Physical meaning
A guide trades frequency for a transverse pattern. The pattern's wavenumber k_c is fixed by the walls, and only the remainder √(k² − k_c²) is left to travel along the guide.
  • Modes: TE (Ez=0), TM (Bz=0); TEM only with two or more conductors. ω2=ωc2+v2kz2.
  • Rectangular: fc=v2(m/a)2+(n/b)2; TE allows one zero index, TM none; dominant TE₁₀, λc=2a, Ey∝sin⁡(πx/a).
  • λg=λ/s, vp=v/s, vg=vs, vpvg=v2; ZTE=η/s, ZTM=ηs; TE₁₀ power E02ab/4ZTE.
  • Below cutoff: α=kc2−k2, about π/a far below.
  • Bouncing waves: sin⁡θ=fc/f, vg=ccos⁡θ.
  • Circular: TE₁₁ dominant (1.841), then TM₀₁ (2.405); fc=vx/2πR.
  • Coax: TEM, Z0=η02πϵrln⁡ba. Lines: Γ=ZL−Z0ZL+Z0, quarter-wave gives Z02/ZL.
  • Cavity: fmnp=v2(m/a)2+(n/b)2+(p/d)2; Q∼V/Sδ.
  • Fibre: NA =n12−n22, single-mode for V<2.405, about V2/2 modes, intermodal spread Ln1c(n1n2−1).

Practise: exam questions on this lesson

From warm-up to top-rank level, with full solutions. More on the practice page.

Before this: lesson 3.7, the Fresnel equations. Next: lesson 3.9, radiation, where waves are launched rather than guided. Back to the GATE Physics course home.

Check yourself

1Why can a hollow rectangular metal pipe not carry a TEM wave?
2A guide's TE10 cutoff is 6 GHz. What happens to a 4 GHz signal?
3In a hollow guide, which quantity is below c for a propagating mode?

Sources

  • D. J. Griffiths, Introduction to Electrodynamics, 4th ed. (2017), chapter 9.5
  • J. D. Jackson, Classical Electrodynamics, 3rd ed. (1999), chapter 8
  • D. M. Pozar, Microwave Engineering, 4th ed. (2012), chapters 2 and 3
  • J. M. Senior, Optical Fiber Communications, 3rd ed. (2009), chapter 2
  • GATE Physics (PH) syllabus, Electromagnetic Theory section, published by the organising institute each year

Your ticks stay in this browser. Save them as a file on the course home.

Updated 2026-11-22. Not affiliated with the IITs, IISc or the GATE organising institute. The general aptitude part of GATE is not covered here. Check the official GATE website for the current pattern. All questions are original.