Home / Learn / Exam prep / GATE Physics / Lesson 9.4
All lessons

Module 9: Electronics · Lesson 9.4 · about 40 min

Oscillators

Sinusoidal and relaxation oscillators at GATE depth: the Barkhausen criterion as a pole pair on the imaginary axis, the RC phase-shift oscillator (gain 29), the Wien bridge (gain 3, unequal parts), LC oscillators (Colpitts, Hartley, Clapp), quartz crystals with series and parallel resonance and huge Q, amplitude stabilisation, and relaxation oscillators.

Key points, meanings and formulas on one page: choose "Save as PDF" in the print box.

Module 9 · about 40 minutes. Lesson 9.2 warned that a feedback loop whose phase reaches −180° with gain above 1 oscillates. An oscillator is that loop built on purpose, with a frequency-selective network that makes it happen at exactly one frequency. The relaxation oscillators of lesson 9.3 are the other family.

A sinusoidal oscillator is an amplifier A and a filter β in a loop. It oscillates at the frequency where the loop phase is a whole number of turns, provided the loop gain there is at least 1. Starting needs a little more than 1; a steady amplitude needs exactly 1, so every real oscillator has some non-linearity that lowers the gain as the amplitude grows.

1. The Barkhausen criterion

With positive feedback the closed-loop gain is A/(1−Aβ). It becomes infinite, an output with no input, when

A(jω0)β(jω0)=1⟺|Aβ|=1  and  ∠Aβ=0∘ (or 360∘n)

Phase picks the frequency. The filter network's phase changes with ω; only at ω₀ does the loop phase come back to zero. A sharper phase change (higher Q) means a more stable frequency.

Gain decides whether it runs. Seen as a differential equation, the loop has a pair of complex poles at σ ± jω₀ with σ ∝ (Aβ − 1). Loop gain above 1 puts them in the right half-plane: the oscillation grows as e^{σt}. Below 1, it dies.

Non-linearity fixes the amplitude. As the amplitude grows, the amplifier begins to saturate and its average gain falls, until the poles sit exactly on the imaginary axis. Gentle limiting gives a cleaner sine than hard clipping.

Start-up comes from noise. No input is needed: thermal noise and the switch-on transient contain every frequency, and the one that satisfies the criterion grows.

2. RC oscillators

RC phase shift. An inverting amplifier (180°) drives three identical RC sections, which must supply the other 180°. Solving the ladder:

VoutVin=11−5/x2−j(6/x−1/x3),x=ωRC⇒ω0=16RC,|β|=129

so the amplifier needs a gain of at least 29. (With low-pass sections, series R and shunt C, the frequency is 6/RC and the gain is still 29.) With R=10 kΩ and C=10 nF: f0=650 Hz.

Wien bridge. A series RC and a parallel RC form a band-pass divider with zero phase at its peak; a non-inverting amplifier closes the loop. For equal parts:

β(jω)=13+j(ωRC−1/ωRC),ω0=1RC,|β(ω0)|=13

The amplifier needs gain 3, usually 1+Rf/R1 with Rf=2R1. With R=10 kΩ and C=16 nF: f0=995 Hz. Tuning both capacitors together (a ganged capacitor) sweeps the frequency over a decade with constant amplitude, which made the Wien bridge the classic audio oscillator. With unequal parts, ω0=1/R1R2C1C2 and the gain needed is 1+R1/R2+C2/C1.

Top: phase and magnitude of the Wien loop gain Kβ; the phase crosses zero only at ω₀, where |Kβ| = K/3. Bottom: the output after a tiny kick, integrated numerically. With an ideal amplifier it grows for K > 3 and decays for K < 3; with soft limiting it settles to a fixed amplitude that grows with the excess gain.

3. LC oscillators

For radio frequencies an LC tank replaces the RC network. In the general three-reactance circuit, the tank is X1 from input to ground, X2 from output to ground and X3 between them; oscillation needs X1+X2+X3=0, with X1,X2 of the same kind and X3 of the other.

Oscillator Tank Frequency Gain condition
Colpitts two capacitors, one inductor 12πLC1C2/(C1+C2) gmR≥C2/C1
Hartley two inductors (mutual M), one capacitor 12π(L1+L2+2M)C gmR≥(L1+M)/(L2+M)
Clapp Colpitts with a small C3 in series with L ≈12πLC3 when C3≪C1,C2 as Colpitts

Worked example. L=100 µH with C1=C2=2 nF: series capacitance 1 nF, f0=503 kHz. A Hartley tank with L1=L2=50 µH (no coupling) and C=1 nF gives the same frequency. The Clapp version is less sensitive to the transistor’s own capacitances, which sit across C1 and C2 and are swamped there.

4. Crystal oscillators

A quartz crystal is a piezoelectric resonator. Its electrical equivalent is a series L, C, R (the mechanical resonance) in parallel with the holder capacitance C0:

fs=12πLC,fp=fs1+CC0≈fs(1+C2C0),Q=1RLC
`$f_s$`
series resonance: the impedance is a minimum, just `$R$`
`$f_p$`
parallel (anti-)resonance: the impedance is a maximum; between `$f_s$` and `$f_p$` the crystal is inductive, and a Pierce or Colpitts circuit uses it as the inductor there
`$C/C_0$`
tiny (around 10⁻³), so `$f_p$` is only a fraction of a percent above `$f_s$` and the crystal fixes the frequency whatever the rest of the circuit does
`$Q$`
10⁴ to 10⁶, compared with about 100 for an LC tank: the phase changes so steeply with frequency that the oscillator cannot drift far

Worked example. L=0.5 H, C=0.05 pF, R=50 Ω, C0=5 pF: fs=1.0066 MHz, fp−fs=5.0 kHz, and Q=63000. Watch crystals use 32 768 Hz = 2¹⁵ Hz, so a chain of 15 flip-flops (lesson 9.6) divides it to exactly 1 Hz.

Relaxation oscillators (astable multivibrators, 555 timers, the UJT oscillator) charge a capacitor until a threshold switches the circuit, then discharge it. They give square or triangle waves, and their frequency depends on an RC time constant and two thresholds rather than on a resonance; their frequency stability is much worse than a crystal’s. A voltage-controlled oscillator makes the charging current proportional to an input voltage, so the frequency follows the voltage.

“Set the loop gain to exactly 1 and the oscillator will run with a steady amplitude.” A linear loop with gain exactly 1 is marginal: any drift in the components makes the amplitude grow without limit or die away. Real oscillators start with gain above 1 and rely on a non-linearity (saturation, a thermistor, a lamp, diodes, or an automatic gain control loop) to bring the average gain down to 1 at the operating amplitude. The figure shows both cases.

  • Barkhausen: Aβ=1; phase sets ω0, gain at least 1 to start, exactly 1 (by non-linearity) to run steadily.
  • RC phase shift: ω0=1/6RC (high-pass ladder), gain 29.
  • Wien: ω0=1/RC, gain 3; unequal parts 1/R1R2C1C2 and 1+R1/R2+C2/C1.
  • Colpitts: C=C1C2/(C1+C2); Hartley: L=L1+L2+2M; Clapp: ≈1/2πLC3.
  • Crystal: fp≈fs(1+C/2C0), Q=L/C/R∼104–106; inductive between fs and fp.

Practise: exam questions on this lesson

Next: lesson 9.5 leaves analogue circuits for logic: Boolean algebra, Karnaugh maps, adders and multiplexers.

Check yourself

1A three-section RC phase-shift oscillator (equal R and C, high-pass ladder) oscillates at
2A Colpitts oscillator has L = 100 µH and C₁ = C₂ = 2 nF. Its frequency is about
3Why does a practical Wien bridge oscillator need an amplitude-control element (a lamp, thermistor, diodes or an AGC loop)?

Sources

  • A. S. Sedra and K. C. Smith, Microelectronic Circuits, 7th ed. (2015), chapter 18
  • P. Horowitz and W. Hill, The Art of Electronics, 3rd ed. (2015), chapter 7
  • J. Millman and C. C. Halkias, Integrated Electronics (1972), chapter 14
  • GATE Physics (PH) syllabus, Electronics section, published by the organising IIT each year

Your ticks stay in this browser. Save them as a file on the course home.

Updated 2026-11-22. Not affiliated with the IITs, IISc or the GATE organising institute. The general aptitude part of GATE is not covered here. Check the official GATE website for the current pattern. All questions are original.