DIY workshop safety: PPE, ladders, clamping and cutting safely at home

Stay safe doing DIY at home: the right glasses, ear and dust protection, when not to wear gloves, clamping, cutting away from you, the 1 in 4 ladder rule, dust and fumes, small cuts and when to stop. Spot seven hazards in a workshop picture and test yourself.

Keep it one tap away for everyday use.

Bookmark Workshop safety?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Gear up
  2. Spot hazards
  3. Quiz
Nothing is uploadedWorks offline once open

Stay safe

  • Safety glasses on for anything that cuts, drills, grinds or hammers. Eyes do not heal like skin.
  • Never wear gloves, loose sleeves, a tie, jewellery or loose long hair near a drill or any spinning tool. They get caught and pull your hand in.
  • Unplug a power tool, or take its battery out, before you change a bit or blade or clear a jam.
  • If you are tired, rushed or unsure, stop. Most accidents happen at the end of the day.

What you need

  • Safety glasses
  • Ear defenders or plugs
  • Dust mask (FFP2 or N95)
  • Work gloves (hand tools only)
  • Sturdy closed shoes
  • Two G-clamps
  • First aid kit
  • Good light

Step by step

  1. Protect your eyes and ears

    Safety glasses (marked to a standard such as EN 166 or ANSI Z87.1) for cutting, drilling, hammering and any job that makes chips or dust. Ordinary glasses are not enough. Ear defenders for loud tools such as a hammer drill, circular saw or grinder.

    If you have to raise your voice to be heard an arm's length away, it is loud enough to need ear protection.

  2. Gloves: yes for rough work, no near spinning tools

    Wear gloves to carry rough timber, sheet metal or rubble. Take them off to use a drill, a lathe, a grinder or any tool that spins: the glove can be caught and wind your hand in.

    The same goes for loose sleeves, rings, watches, ties and long hair. Roll, remove or tie them back.

  3. Keep the space tidy

    Clear off-cuts and tools off the floor as you go. Run extension leads along the wall, not across where you walk, and unwind a cable reel fully so it does not overheat. Keep children and pets out while you work.

    Good light matters: you cannot cut to a line you cannot see.

  4. Clamp the work

    Hold the work in a vice or with two clamps, so it cannot spin or slide and both your hands are free. Never hold a small piece in your fingers while you drill it.

    A drill bit that catches can spin a loose piece round like a blade.

  5. Cut away from your body, keep blades sharp

    Push or pull a blade so that if it slips, it goes away from you and your other hand. Keep the hand that holds the work behind the blade, never in front of it. A sharp blade is safer than a blunt one: it needs less force, so it slips less.

    Retract or cover the blade every time you put a knife down.

  6. 14

    Ladders: 1 in 4, three points of contact

    Set a leaning ladder at about 75°: 1 unit out at the foot for every 4 units up. On firm, level ground, with the top resting on something solid. Keep three points of contact (two feet and a hand) and your belt buckle between the stiles.

    Move the ladder rather than leaning out. Do not stand on the top three rungs.

  7. Dust and fumes

    Sanding, cutting MDF and sweeping make fine dust. Wear a dust mask rated FFP2 or N95 (a thin paper mask does little), vacuum rather than sweep, and work with a window open or outdoors. Paints, glues and solvents need fresh air too: read the tin.

    In an older house, sanding or scraping old paint can release lead. Test first and check your local advice.

  8. First aid for small cuts

    Rinse a small cut under clean running water, press on it with a clean cloth until it stops bleeding, then cover it with a plaster. Keep a first aid kit where you work.

    Get medical help for a deep cut, one that will not stop bleeding after 10 minutes of firm pressure, anything in the eye, or a cut from a dirty or rusty object if your tetanus jabs are not up to date.

  9. STOP

    Know when to stop

    Stop when you are tired, rushed, cold, or have had a drink. Stop when a tool behaves oddly: smoke, a burning smell, a damaged lead or a blade that binds. Stop and ask when you are not sure how to do the next step.

    A job left until tomorrow is better than a trip to hospital tonight.

Spot the hazards

This workshop has seven things wrong with it. Tap each one to see what is wrong and how to fix it, then press Test me.

Before you start a job: put it in order

Call a professional when

  • The job needs electrical wiring, gas or more than a simple plumbing fix: call an electrician, gas engineer or plumber.
  • You need to work at height beyond a short stepladder, or on a roof.
  • You suspect asbestos (some older boards, floor tiles and textured ceilings): do not drill, cut or sand it; get it tested.
  • Someone is badly hurt: call emergency services (999, 911, 112 or your local number).

Check yourself

What it does

This lesson covers the safety habits that prevent most DIY injuries at home: protecting your eyes, ears and lungs, knowing when gloves help and when they are dangerous, keeping the floor clear, clamping work, cutting away from your body, setting up a ladder, and dealing with a small cut. There are nine illustrated steps you can tick, a spot the hazards workshop picture with seven things wrong in it, a put-in-order activity for the routine before a job, and a short quiz.

It is the second lesson of the free Hand tools and safety course. If you are new to the tools themselves, start with know your hand tools; next, learn to measure accurately in measure and mark, then plan your cuts with the cut list.

How to use it

  1. Read the Stay safe box and the steps. Tick each step as you understand it, or as you set it up in your own space. Ticks are only kept if you tick Remember my ticks on this device, and then only in this browser.
  2. In Spot the hazards, tap anything in the picture that looks wrong. Each hazard explains the danger and the fix. Press Test me to be asked for each hazard in turn.
  3. Put the before-you-start routine in order, then take the quiz.
  4. Print checklist gives you a one-page reminder to pin up in your shed or garage.

What each piece of protection does

  • Safety glasses: stop chips and dust hitting your eyes. Look for a standard mark such as EN 166 (Europe, UK) or ANSI Z87.1 (US).
  • Ear defenders or plugs: for hammer drills, saws, grinders and long spells of loud work. Hearing damage builds up and does not come back.
  • Dust mask (FFP2 or N95): for sanding, cutting MDF and sweeping up. A thin paper mask does very little.
  • Gloves: for carrying rough or sharp material. Never near a spinning tool.
  • Sturdy closed shoes: protect your feet from dropped tools and timber.

Worked example

You are about to drill holes for a shelf in the garage. Before you start you clear the off-cuts from the floor, run the extension lead along the wall and send the dog indoors. You check the drill’s lead for damage, roll up your sleeves and take off your watch, then put on safety glasses and a dust mask. The shelf bracket hole is above head height, so you set the stepladder fully open on level ground rather than stretching. You clamp the shelf board to the bench to drill it, unplug the drill to change bits, and tidy up when you finish.

FAQs

Are normal glasses good enough? No. They are not made to stop impacts and leave the sides open. Wear safety glasses over them, or get prescription safety glasses.

Why not wear gloves when drilling? A glove can catch on the spinning chuck or bit and wind your hand in faster than you can let go. Bare, dry hands are safer with spinning tools.

What is the 1 in 4 rule? For a leaning ladder, the foot should be 1 unit out from the wall for every 4 units of height up to where it rests. That makes an angle of about 75°.

When does a cut need a doctor? If it is deep or gaping, will not stop bleeding after 10 minutes of firm pressure, has something stuck in it, or came from a dirty or rusty object and your tetanus jabs are not up to date. Anything in the eye needs medical help. In an emergency call your local emergency number.

Where the numbers come from

  • Advice follows general guidance from workplace safety bodies (such as the UK HSE's ladder and PPE guidance and US OSHA's hand and power tool guidance) and first aid charities. The 1 in 4 ladder angle (about 75°) is the common rule for leaning ladders. Check the instructions for your own tools and ladder. Drawings are fibub's own.
  • Mask ratings: FFP2 (Europe, UK) and N95 (US) are both rated to filter at least 94 to 95 percent of fine particles when well fitted.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-16.

Change log for Workshop safety

  1. Home skills: link hand tools lessons and cut list with carpentry Details on GitHub
  2. Hand tools and safety course: #L373 know your hand tools, #L374 workshop safety, #L375 measure and mark, #T1011 cut list Details on GitHub

Every change to fibub

Related tools

Know your hand tools #L373 Learn the 13 tools in a basic home tool kit: what each one is for, how to hold it and the common mistake to avoid. Tap the tool wall to name them, tick the ones you have, and test yourself on which tool fits the job. Measure and mark #L375 Read a tape measure in millimetres and in inch fractions, use the sliding hook, mark with a V, draw square lines, check a corner with the 3-4-5 rule and check a level. Practise on a drawn tape with endless random readings. Cut list #T1011 Type the length of the boards you can buy, the saw kerf and the pieces you need. The cut list packs them onto the fewest boards, draws each board with its cuts and offcut, and gives the waste and a list to copy or print. Millimetres or inches. Saw a straight cut #L376 Saw a straight, square cut in wood with a handsaw in seven illustrated steps: mark a square line, clamp the work, cut on the waste side of the line, start with short strokes and let the saw do the work. Try the kerf sim to see why the side of the line matters. Change a flat tyre #L370 Change a flat car tyre onto the spare in eight illustrated steps: get safe, loosen the nuts, jack at the right point, swap the wheel and tighten in a star pattern. Tick each step, name the parts, and print the checklist for your glovebox. Plug a tyre puncture #L371 Plug a nail or screw hole in a tubeless car tyre with a string plug kit in eight illustrated steps, check first whether the hole can be repaired at all, and learn why most tyre makers treat an outside plug as a temporary fix.