Basic hand tools and their uses: a home tool kit with names, pictures and how to hold them

Learn the 13 tools in a basic home tool kit: what each one is for, how to hold it and the common mistake to avoid. Tap the tool wall to name them, tick the ones you have, and test yourself on which tool fits the job.

Keep it one tap away for everyday use.

Bookmark Know your hand tools?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Tool cards
  2. Name them
  3. Pick a tool
Nothing is uploadedWorks offline once open

Stay safe

  • Wear safety glasses for anything that cuts, drills or hammers. Bits of metal and wood fly further than you think.
  • Keep blades sharp and covered when not in use, and store tools out of reach of children.
  • Hold the work in a clamp or vice, not in your hand, when you saw, drill or chisel.
  • No tool in this kit is for electrical wiring. Leave that to an electrician.

A basic home tool kit

  • Claw hammer
  • Flat screwdriver
  • Phillips and Pozidriv screwdrivers
  • Tape measure
  • Combination square
  • Spirit level
  • Utility knife
  • Combination pliers
  • Adjustable spanner
  • Hand saw
  • Two G-clamps
  • Cordless drill
  • Stud finder
  • Safety glasses

You do not need it all at once. A hammer, two screwdrivers, a tape measure and a knife cover most small jobs.

Tool cards

Each card says what the tool is for, how to hold it, and one common mistake. Tick a card when you have the tool or know how to use it.

  1. Claw hammer

    For: driving nails and pulling them out with the claw. Hold: near the end of the handle and let the weight of the head do the work. Start a nail with light taps, fingers holding it low down.

    Common mistake: holding the hammer by the neck. You lose power and hit your fingers more.

  2. FlatPhillipsPozidriv

    Screwdrivers

    For: turning screws. Match the tip to the head: flat, Phillips (a plain cross) or Pozidriv (a cross with four small extra lines, common in Europe and the UK). Hold: push in hard and turn; most of the effort is the push.

    Common mistake: a Phillips driver in a Pozidriv screw. It slips out and chews the head.

  3. Tape measure

    For: measuring lengths. A 5 m (16 ft) tape is a good size. Hold: hook the end over the edge, pull the blade straight and read where it meets the mark.

    Common mistake: letting the blade sag or bend round a corner. It reads long. The Measure and mark lesson shows how to read it.

  4. Combination square and spirit level

    Square: press its stock against a straight edge and draw along the blade for a line at exactly 90° (it also does 45°). Level: the bubble sits between the lines when a surface is level (or plumb, held upright).

    Common mistake: trusting a cheap level. Check it: read it, turn it end for end, read again. Both should match.

  5. Utility knife

    For: scoring plasterboard, cutting carpet, card and string, and marking wood. Hold: like a pen for light cuts, firm in the fist for heavy ones; cut along a straight edge with your other hand behind the blade.

    Common mistake: pushing hard with a blunt blade. Snap off or change the blade; a sharp blade needs less force and slips less.

  6. Pliers and adjustable spanner

    Pliers: grip, bend and cut wire or hold small parts. Spanner: turns nuts and bolts. Close the jaws tight on the flats and pull so the fixed jaw takes the load.

    Common mistake: using pliers on a nut. They round its corners. Use a spanner that fits.

  7. Hand saw

    For: cutting wood to length. Hold: index finger pointing along the handle, arm, shoulder and saw in one line. Start with a few short pull strokes, then use the full blade at about 45°.

    Common mistake: forcing it. Let the saw's weight cut; pushing hard makes it wander off the line.

  8. G-clamps

    For: holding work still while you saw, drill or glue, so both hands are free and safe. Use: two clamps, with scraps of wood under the pads so they do not dent the work.

    Common mistake: holding the work with one hand and sawing with the other. That is how most cuts to the hand happen.

  9. Cordless drill and stud finder

    Drill: makes holes and drives screws. Set the clutch (the numbered ring) low for screws so it slips before the screw head breaks. Stud finder: finds the wooden or metal studs behind a hollow wall. Many also warn of live cables, but none is a guarantee.

    Common mistake: changing a bit with the battery on. Take the battery out first.

Name the tools

Call a professional when

  • The job involves electrical wiring, sockets or lights: call an electrician.
  • It involves gas or water pipes beyond a simple tap washer: call a gas engineer or plumber.
  • You need a tool you have never used that could hurt you badly, such as a chainsaw or a table saw, and nobody can show you how.
  • The job is structural, such as removing a wall or cutting a joist.

Check yourself: which tool for the job?

What it does

This lesson is a tour of a basic home tool kit: the thirteen hand tools that cover most small jobs around the house, from hanging a picture to building a simple shelf. Each tool card has a drawing and says three things: what the tool is for, how to hold it, and the one mistake almost everyone makes at first. Tick a card when you have the tool or feel sure you know how to use it.

Then tap the tool wall to learn each tool’s name, press Test me to see if you remember them, and finish with a short quiz that asks which tool fits a job. It is the first lesson of the free Hand tools and safety course. Next, learn to keep yourself safe in workshop safety, then measure accurately in measure and mark, and when you plan a project, let the cut list work out how many boards to buy.

How to use it

  1. Read the Stay safe box first.
  2. Work through the tool cards. Tick each one you have or know. Ticks stay on this page only, unless you tick Remember my ticks on this device; then they are kept in this browser and never sent anywhere. Print checklist gives you a shopping list to take to the shop.
  3. On the tool wall, tap any tool to see its name and what it does. Press Test me and the page asks you to find each tool in turn, with a score at the end.
  4. Take the quiz. Each time you press for new questions you get a different mix.

What each tool does

  • Claw hammer: drives nails and pulls them out. A 16 oz (450 g) head suits most people.
  • Screwdrivers: flat for slotted screws, Phillips and Pozidriv for cross-head screws. They look alike but are different shapes; Pozidriv heads have four small extra lines.
  • Tape measure: a 5 m (16 ft) tape with both metric and inch markings is handy.
  • Combination square: marks and checks 90° and 45° lines.
  • Spirit level: checks level (horizontal) and plumb (upright).
  • Utility knife: cuts card, carpet and plasterboard, and marks wood more finely than a pencil.
  • Combination pliers: grip, bend and cut wire.
  • Adjustable spanner: turns nuts and bolts of many sizes.
  • Hand saw: cuts wood to length.
  • G-clamps: hold the work so your hands stay clear of the blade.
  • Cordless drill: drills holes and drives screws; the clutch stops it over-tightening.
  • Stud finder: finds the timber or metal studs behind a hollow wall.

Worked example

You want to put up a small shelf on a plasterboard wall. You use the stud finder to find a stud and mark it, the tape measure to set the height, and the spirit level to draw a level line. The cordless drill makes pilot holes and drives the screws, with the clutch set low. If the shelf board is too long, you mark a square line with the combination square, clamp the board with two G-clamps and cut it with the hand saw. Safety glasses go on before the first hole.

FAQs

What should I buy first? A claw hammer, a flat and a cross-head screwdriver, a tape measure and a utility knife. Add a drill, level and saw when a job needs them.

Are cheap tools worth it? For a hammer or a tape, a mid-priced one lasts for years. Cheap screwdrivers and spanners often have soft tips that round off and slip, which is when hands get hurt.

Can a stud finder find live cables? Many have a cable mode, but none is a guarantee. Read the wall-fixings lessons for safe zones, and never drill where you are unsure. If you hit a cable, stop and call an electrician.

What is the difference between Phillips and Pozidriv? Both are cross-head drives. Pozidriv has straighter sides and extra small lines on the screw head, so it grips better. Use the matching driver, or the tip will slip and damage the head.

Where the numbers come from

  • Tool uses and handling follow general advice from tool makers' instructions and home-improvement guides. Pozidriv and Phillips are trade names for two different cross-head drive shapes. Drawings are fibub's own.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-16.

Change log for Know your hand tools

  1. Hand tools and safety course: #L373 know your hand tools, #L374 workshop safety, #L375 measure and mark, #T1011 cut list Details on GitHub

Every change to fibub

Related tools

Workshop safety #L374 Stay safe doing DIY at home: the right glasses, ear and dust protection, when not to wear gloves, clamping, cutting away from you, the 1 in 4 ladder rule, dust and fumes, small cuts and when to stop. Spot seven hazards in a workshop picture and test yourself. Measure and mark #L375 Read a tape measure in millimetres and in inch fractions, use the sliding hook, mark with a V, draw square lines, check a corner with the 3-4-5 rule and check a level. Practise on a drawn tape with endless random readings. Cut list #T1011 Type the length of the boards you can buy, the saw kerf and the pieces you need. The cut list packs them onto the fewest boards, draws each board with its cuts and offcut, and gives the waste and a list to copy or print. Millimetres or inches. Change a flat tyre #L370 Change a flat car tyre onto the spare in eight illustrated steps: get safe, loosen the nuts, jack at the right point, swap the wheel and tighten in a star pattern. Tick each step, name the parts, and print the checklist for your glovebox. Plug a tyre puncture #L371 Plug a nail or screw hole in a tubeless car tyre with a string plug kit in eight illustrated steps, check first whether the hole can be repaired at all, and learn why most tyre makers treat an outside plug as a temporary fix. Fix a bike puncture #L372 Patch a bicycle inner tube in nine illustrated steps: take the wheel off, lever the tyre off, find the hole and the thorn, roughen, glue, patch and refit without pinching. Name the parts of a bike wheel and test yourself.