How to plug a tyre puncture: tubeless plug kit steps, where it is safe and when to see a tyre shop

Plug a nail or screw hole in a tubeless car tyre with a string plug kit in eight illustrated steps, check first whether the hole can be repaired at all, and learn why most tyre makers treat an outside plug as a temporary fix.

Keep it one tap away for everyday use.

Bookmark Plug a tyre puncture?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Find hole
  2. Plug it
  3. Test seal
Nothing is uploadedWorks offline once open

Stay safe

  • Work well away from traffic, on firm, flat ground, with the parking brake on and the engine off. Never reach under a car held up only by a jack.
  • Wear safety glasses and gloves. The reamer and needle are sharp, and wire from a steel belt can stick out of the hole.
  • A string plug from outside is a temporary repair in most tyre makers' eyes. Drive gently and get a tyre shop to check the tyre and fit a proper repair from the inside soon.
  • Never plug the sidewall or shoulder, a cut or slit, or a hole bigger than about 6 mm (1/4 in). Fit the spare instead.

What you need

  • Tubeless plug kit (reamer, insertion needle, string plugs)
  • Pliers
  • Knife or scissors
  • Chalk or a marker
  • Soapy water in a spray bottle
  • Pump or compressor
  • Pressure gauge
  • Safety glasses and gloves

Step by step

  1. Find the hole

    Look round the tread for a nail, screw or stone. No luck? Pump the tyre up a little and spray soapy water on the tread: bubbles grow where air comes out. Draw a chalk ring round the hole.

    Roll the car forward a little, or take the wheel off, to see the part of the tyre that was on the ground.

  2. Check it can be plugged

    Only plug a round hole in the middle part of the tread, up to about 6 mm (1/4 in) across. Not the shoulder, not the sidewall, not a cut. If the tyre was driven flat, or it is a run-flat tyre, a tyre shop needs to look inside.

    Use the "Can this be plugged?" checker below.

  3. Pull the object out

    Note the angle it went in at, then pull it straight out with pliers. The tyre will go down, which is fine: you will pump it up again.

    If it is a long bolt or something wide, stop and use the spare.

  4. Ream the hole

    Push the reamer (the rough, file-like spike) into the hole along the same angle as the object, and work it in and out several times. This cleans and roughens the hole so the plug grips.

    It takes a firm push. Hold the handle with both hands and keep your face out of line.

  5. Load a plug

    Peel a string plug off its backing and push it through the eye of the insertion needle until the same length sticks out each side. If your kit has rubber cement, coat the plug with it.

    Plugs are sticky: keep them clean and off the ground.

  6. Push the plug in

    Push the needle into the hole until about a third of the plug (1 to 2 cm) is still outside. Then pull the needle straight out in one quick, steady move. The plug stays in, folded in two.

    Do not twist the needle as you pull it out, or the plug can come with it.

  7. Trim the ends

    Cut the loose ends off level with the tread (leave a stub of a couple of millimetres rather than cutting into the tyre). Do not pull on the plug while you cut.

  8. Pump up and check

    Pump to the pressure on the door-jamb label or in the handbook. Spray soapy water on the plug: no bubbles means it is sealed. Check the pressure again after a short drive and the next morning.

    Book a tyre shop to check it and fit a plug-patch from inside. Until then, drive gently.

Can this be plugged?

A guide only, based on common tyre-repair rules (such as the UK standard BS AU 159 and US tyre industry guidance). Rules differ by country and tyre maker: check your local rules and ask a tyre shop.

Where on the tyre?

A tyre cut through, as if sliced across. Tap a part to see what it is and whether a hole there can be repaired.

Put the steps in order

Call a professional when

  • The hole is in the shoulder or sidewall, is a cut or slit, or is bigger than about 6 mm (1/4 in).
  • The tyre was driven flat or very low, has a bulge, or it is a run-flat tyre.
  • The plug still leaks after a second try, or the tyre keeps losing pressure.
  • Always, soon after a roadside plug: a tyre shop can take the tyre off, check the inside and fit a plug-patch.

Check yourself

What it does

This lesson shows you how to plug a small puncture in a tubeless car tyre with a string plug kit, the kind sold in car shops for a few pounds or dollars. A nail or screw in the tread is the most common puncture, and a plug can get you home or to a tyre shop without fitting the spare. Each of the eight steps has a drawing and a Done tick. Before you start, the Can this be plugged? checker asks where the hole is, how big it is and what happened, and tells you whether a plug is sensible. The cut-through tyre picture shows which parts can be repaired and which cannot, then a put-in-order activity and a quiz check that it has stuck.

Be honest with yourself about what a plug is. Many tyre makers, and the UK repair standard BS AU 159, treat a string plug pushed in from outside as a temporary fix. A proper repair is a plug-patch fitted from inside, by a tyre shop, after they have taken the tyre off the rim and checked the inside for hidden damage.

It is the second lesson of the free Tyres and punctures course. If the hole cannot be plugged, fit the spare with the change a flat tyre lesson, then set the pressure with tyre pressure.

How to use it

  1. Read Stay safe. Work away from traffic, with the car on firm, flat ground.
  2. Use the Can this be plugged? checker. If it says no, stop and fit the spare.
  3. Follow the steps and tick each one. Ticks are kept only if you tick Remember my ticks on this device.
  4. Tap the parts of the cut-through tyre, then press Test me. Put the steps in order and take the quiz.

What each part means

  • Middle of the tread: the repair zone. A round hole up to about 6 mm (1/4 in) can be plugged here.
  • Shoulder: the curved edge where tread meets side. It flexes too much: no repairs.
  • Sidewall: the side of the tyre. A hole, cut or bulge here means a new tyre.
  • Bead: the stiff edge that seals on the rim. Damage here means a new tyre.
  • Inner liner: the airtight skin inside, where a tyre shop fits a plug-patch.
  • Reamer and needle: the reamer cleans and roughens the hole; the needle carries the plug in.

Worked example

You find a screw in the middle of the front-right tread. The checker says: middle of the tread, about 4 mm, not driven flat, not a run-flat, so yes. You pull the screw out at the angle it went in, ream the hole six times, thread a plug halfway through the needle and push it in until about a third is still showing. You pull the needle out in one quick move, trim the ends, and pump the tyre to the 2.3 bar (33 psi) on the door label. Soapy water shows no bubbles. Next morning the pressure is still 2.3 bar, and you book a tyre shop to check it and fit a plug-patch.

FAQs

Is it legal to drive on a plugged tyre? Rules differ by country. In the UK, repairs to car tyres are expected to meet BS AU 159, which an outside string plug alone does not. Treat it as a way to get to a tyre shop and check your local rules.

Can I plug a tyre with an inner tube? No. Plug kits are for tubeless tyres only. A tube needs a patch (see the bike puncture lesson for how patching works).

How fast can I drive on a plug? Gently and at normal speeds until it is checked. Avoid long, fast motorway runs.

Can a tyre have more than one repair? Sometimes, if the holes are far enough apart. A tyre shop decides; the rules set a minimum gap.

Where the numbers come from

  • Repair limits (central part of the tread only, no shoulder or sidewall repairs, holes up to about 6 mm in car tyres, inspection inside after running flat) follow the UK standard BS AU 159 for tyre repairs and published US tyre industry guidance (USTMA and the Tire Industry Association), which call for a combined plug and patch fitted from inside. Summarised in fibub's own words; checked 2026-11-16. Rules differ by country and tyre maker: check your local rules.
  • Plug kit steps follow the general instructions printed with string plug kits. Always read your own kit's instructions. Drawings are fibub's own.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-16.

Change log for Plug a tyre puncture

  1. Tyres and punctures: #L371 plug a tyre puncture, #L372 fix a bike puncture, #T1010 wheel nut torque Details on GitHub

Every change to fibub

Related tools