How to saw wood straight by hand: mark, clamp, start the cut and cut on the waste side

Saw a straight, square cut in wood with a handsaw in seven illustrated steps: mark a square line, clamp the work, cut on the waste side of the line, start with short strokes and let the saw do the work. Try the kerf sim to see why the side of the line matters.

Keep it one tap away for everyday use.

Bookmark Saw a straight cut?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Mark
  2. Saw
  3. Check
Nothing is uploadedWorks offline once open

Stay safe

  • Wear safety glasses. Sawdust and splinters fly up towards your face.
  • Clamp the wood to a bench or trestle. Never hold it on your knee or in your hand while you saw.
  • Keep your free hand behind the saw and out of its path, and use your thumb as a guide only for the first few slow strokes.
  • Hang a saw up or put a guard on the teeth when you finish, and keep children away from the bench.

What you need

  • Handsaw (cross-cut or pull saw)
  • Tape measure
  • Pencil
  • Try square or speed square
  • Clamps
  • Bench or trestles
  • Safety glasses
  • Sandpaper

Step by step

  1. 600

    Measure and mark

    Check one end is square first. Hook the tape on that end, measure your length and make a small V mark with the point exactly at the length.

    A V mark is easier to find again than a dot or a dash.

  2. Square a line across

    Hold the square's thick stock tight against the edge, slide it to the V and draw the line along the blade. Carry the line onto the edge too, so you can see the saw from the side.

    Use a sharp pencil. A fat line is hard to cut to.

  3. keepwaste

    Mark the waste side

    Put a cross on the side of the line you will throw away. You will saw on that side, with the line just left showing on your piece.

    The saw cuts a slot (the kerf). Cut on the waste side and the slot comes out of the waste, not your piece.

  4. Clamp the work

    Clamp the board to the bench with the line just past the end, about 2 to 5 cm out, on the waste side. The wood should not move or bounce when you push on it.

    Too far out and the end vibrates. Too close and you saw into the bench.

  5. Start the cut

    Rest the blade on the waste side of the line, against the side of your thumb knuckle. Make two or three short, light pull strokes to cut a small notch. Then move your thumb well away.

    Do not push to start. The teeth bounce and jump out.

  6. 45°

    Saw with long, light strokes

    Hold a cross-cut handsaw at about 45 degrees to the wood. Use the whole length of the blade and let its weight do the cutting. Keep your eye, arm and the saw in one straight line.

    If it drifts, twist the blade very gently back towards the line over a few strokes.

  7. Support the offcut

    Near the end, slow down and hold up the waste piece (or have a helper hold it). If it drops, it tears a splinter off the bottom edge of your piece.

    Short, gentle strokes for the last 1 cm.

  8. Check it is square

    Hold the square against the face and then the edge of the cut end. No light under the blade means it is square. Sand off the fuzzy edges (the arris) with a sanding block.

    A little out? Sand or plane the high side. A lot out? Cut again a little further along.

Kerf sim: which side of the line?

A saw cuts a slot, the kerf, as wide as its teeth are set. Pick which side of your pencil line the saw runs and see what you get.

How many pieces from one board?

Name the parts

Put the steps in order

Call a professional when

  • You need many long, dead straight cuts in sheets (plywood, worktops): a timber yard or DIY store can often cut boards to size for you.
  • The wood has nails, screws or old paint that may contain lead: remove metal first, and ask about safe handling of old painted wood.
  • You want to use a power saw for the first time: get someone experienced to show you, and read the manual and its guard rules.
  • The job is structural (stairs, floor joists, roof timbers): talk to a carpenter or builder.

Check yourself

What it does

This lesson shows you how to saw a piece of wood straight and square with an ordinary handsaw, the kind of cut you need for a shelf, a frame or a box. Each of the seven steps has a drawing and a Done tick, so you can follow along at the bench. The kerf sim shows why it matters which side of the pencil line you cut on: pick a side and see the piece come out the right length or a little short. A put-in-order list and a short quiz check what you learned, and you can print the steps.

It is the first lesson of the free Light carpentry course. Next, join your cut pieces with drilling and screwing, then put both skills together to build a simple shelf.

How to use it

  1. Read the Stay safe box. Wear safety glasses and clamp the wood before you start.
  2. Work down the steps with a scrap piece of wood first. Tick each step as you do it. Ticks are not saved unless you tick Remember my ticks on this device.
  3. Try the kerf sim: set where you marked, how wide your saw cuts and which side you cut on.
  4. Put the steps in order and take the quiz.

What each part means

  • Square line: a pencil line at exactly 90 degrees to the edge, drawn against a try square or speed square. Carry it round onto the edge so you can see if the saw drifts.
  • Waste side: the side of the line you will throw away. Mark it with a cross so you never forget.
  • Kerf: the slot the saw cuts. It has width, so it eats some wood. Cut on the waste side and the kerf comes out of the waste, not your piece.
  • Cross-cut: a cut across the grain, the most common cut at home. A cross-cut handsaw works best held at about 45 degrees to the wood.

Worked example

You need a shelf 600 mm (about 23⅝ in) long. You measure 600 mm from the square end, make a small V mark, square a line across and put a cross on the waste side. Your saw cuts a kerf about 2 mm wide. If you saw right down the middle of the line, the piece comes out 599 mm. If you saw on the wrong side, it is 598 mm, and two shelves cut that way will not match. Saw on the waste side with the line just showing and the piece is 600 mm. From a 2400 mm board with a 3 mm kerf you get only three 600 mm pieces, not four: each cut eats 3 mm.

FAQs

Why does my saw wander off the line? Usually you are pushing too hard or twisting the handle. Use long, light strokes, keep your arm, shoulder and the saw in one line, and look down on the saw so you can see both sides of the blade.

Why does the wood split at the end of the cut? The offcut drops and tears the last fibres. Hold or support the offcut for the last few strokes and slow down.

Pull saw or push saw? Both work. Japanese-style pull saws cut on the pull stroke, have a thin kerf and are easy to start. Western handsaws cut on the push. Hold either one lightly.

How do I check the cut is square? Hold a try square against the face and the edge of the cut end. If light shows under the blade, plane or sand the high side.

Where the numbers come from

  • Steps follow general woodworking practice for hand sawing (mark with a square, cut on the waste side, start with the thumb as a guide, about 45 degrees for a cross-cut handsaw, support the offcut). Drawings are fibub's own.
  • Kerf (the width of wood a blade removes) is roughly 1 to 2 mm for a fine handsaw and 2.5 to 3.5 mm for a circular saw blade; check your own saw.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-16.

Change log for Saw a straight cut

  1. Home skills: link hand tools lessons and cut list with carpentry Details on GitHub
  2. Light carpentry course: saw a straight cut (#L376), drill and screw wood (#L377), build a simple shelf (#L378), shelf load (#T1012) Details on GitHub

Every change to fibub

Related tools

Workshop safety #L374 Stay safe doing DIY at home: the right glasses, ear and dust protection, when not to wear gloves, clamping, cutting away from you, the 1 in 4 ladder rule, dust and fumes, small cuts and when to stop. Spot seven hazards in a workshop picture and test yourself. Measure and mark #L375 Read a tape measure in millimetres and in inch fractions, use the sliding hook, mark with a V, draw square lines, check a corner with the 3-4-5 rule and check a level. Practise on a drawn tape with endless random readings. Drill and screw wood #L377 Join two pieces of wood with screws that pull tight and do not split the wood: pick the screw length, drill a clearance hole and a pilot hole, countersink, set the drill's clutch and drive straight. The screw picker suggests length, gauge and drill sizes. Build a simple shelf #L378 Make a wooden wall shelf from one board and two brackets in nine illustrated steps: plan the size and load, cut and sand the board, screw on the brackets, finish it and hang it level. Label the parts, put the steps in order and check yourself. Shelf load #T1012 Work out how hard a wall shelf pulls on each screw. Type what goes on it (or pick books, plates or plants), the shelf depth and the bracket size, and see the pull-out and downward load per screw in kg and newtons, compared with your wall fixing's rating, with a side-view drawing of the forces. Change a flat tyre #L370 Change a flat car tyre onto the spare in eight illustrated steps: get safe, loosen the nuts, jack at the right point, swap the wheel and tighten in a star pattern. Tick each step, name the parts, and print the checklist for your glovebox.