Cut list calculator: fit your pieces onto the fewest boards, with saw kerf

Type the length of the boards you can buy, the saw kerf and the pieces you need. The cut list packs them onto the fewest boards, draws each board with its cuts and offcut, and gives the waste and a list to copy or print. Millimetres or inches.

Keep it one tap away for everyday use.

Bookmark Cut list?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Board size
  2. Pieces
  3. Cut plan
Nothing is uploadedWorks offline once open

Boards you can buy

Kerf is the width of wood the saw blade turns to dust in each cut: about 3 mm (1/8 in) for most hand saws and circular saws. Width is only used to label your shopping list.

Pieces you need

Cut plan

 

Everything is worked out on this page. Nothing you type is stored or sent anywhere.

What it does

Before you go to the timber yard, you need to know how many boards to buy. The cut list takes the length of the boards you can buy, the width of your saw cut (the kerf) and the list of pieces you need, and fits the pieces onto the fewest boards. Each board is drawn as a bar with its pieces and the offcut left at the end, and you get the total boards to buy, how much is wasted, and a list to copy or print and take to the saw.

It packs pieces longest first, and for jobs of up to 24 pieces it also searches every arrangement to prove the board count is the lowest possible. It works in millimetres or inches, with fractions. To mark the pieces accurately, see measure and mark; for the tools you will cut them with, see know your hand tools; and for a whole deck, use the deck calculator.

How to use it

  1. Choose Millimetres or Inches.
  2. Type the board length you can buy, for example 2400 mm or 96 in (8 ft). Width is optional and only labels the shopping list.
  3. Set the saw kerf. 3 mm (1/8 in) suits most saws. Thin Japanese pull saws cut about 1 mm wide.
  4. Add each piece: a name, its finished length and how many. Press Add a piece for more rows, or × to remove one.
  5. Read the cut plan. Copy cut list puts it on your clipboard; Print prints just the plan.

What each setting does

  • Board length: the stock length. If the board ends are split or rough, type the length after trimming them off.
  • Kerf: each saw cut turns this width into dust. Three pieces on a board need two cuts between them, plus one more if there is an offcut.
  • Pieces: finished lengths. The plan cuts across the board only, so it assumes every piece is the board’s width. For pieces of different widths, make a separate list per width.

Worked example

A small bookcase needs two sides of 1200 mm, four shelves of 764 mm and a top of 800 mm, cut from 2400 mm boards with a 3 mm kerf. Without the kerf, two sides would fit exactly on one board, but the cut between them needs 3 mm, so they cannot. The cut list puts three shelves on one board (764 × 3 + 2 cuts = 2298 mm, plus a final cut, leaving a 99 mm offcut), a side and the top on the second (394 mm offcut) and a side and a shelf on the third (430 mm offcut). That is 3 boards, the fewest possible, with 6256 mm of 7200 mm used: 13.1% waste.

FAQs

Why does it want more boards than I expected? Usually the kerf. Pieces that add up to exactly a board’s length never fit on it, because each cut eats a few millimetres.

Is it always the best plan? For up to 24 pieces it proves the fewest boards. For bigger lists it packs longest first, which is usually within one board of the best, and says so.

Can it plan sheets like plywood? No, it plans lengths only. For sheets, plan rips (cuts along the length) by hand first, then use this for the cross-cuts.

Does it save my list? No. Nothing is stored or sent. Copy or print the list before you close the page.

Where the numbers come from

  • The packing is fibub's own: first-fit decreasing (each piece, longest first, goes on the first board with room), then an exact search for the fewest boards when the job is small. Each cut removes one kerf of wood; a 3 mm (1/8 in) kerf is typical of hand saws and circular saw blades, but check your own blade.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-16.

Change log for Cut list

  1. Hand tools and safety course: #L373 know your hand tools, #L374 workshop safety, #L375 measure and mark, #T1011 cut list Details on GitHub

Every change to fibub

Related tools

Deck calculator #T872 Count the deck boards, joists and screws or hidden clips for a deck from its size, board width, gap, the board lengths you can buy and joist spacing. Stair calculator #T873 Work out the number of risers and treads, riser height, total run, stringer length and angle for a straight stair, and check them against editable code limits. Know your hand tools #L373 Learn the 13 tools in a basic home tool kit: what each one is for, how to hold it and the common mistake to avoid. Tap the tool wall to name them, tick the ones you have, and test yourself on which tool fits the job. Workshop safety #L374 Stay safe doing DIY at home: the right glasses, ear and dust protection, when not to wear gloves, clamping, cutting away from you, the 1 in 4 ladder rule, dust and fumes, small cuts and when to stop. Spot seven hazards in a workshop picture and test yourself. Measure and mark #L375 Read a tape measure in millimetres and in inch fractions, use the sliding hook, mark with a V, draw square lines, check a corner with the 3-4-5 rule and check a level. Practise on a drawn tape with endless random readings. Build a simple shelf #L378 Make a wooden wall shelf from one board and two brackets in nine illustrated steps: plan the size and load, cut and sand the board, screw on the brackets, finish it and hang it level. Label the parts, put the steps in order and check yourself. Shelf load #T1012 Work out how hard a wall shelf pulls on each screw. Type what goes on it (or pick books, plates or plants), the shelf depth and the bracket size, and see the pull-out and downward load per screw in kg and newtons, compared with your wall fixing's rating, with a side-view drawing of the forces.