How to read a tape measure (mm and inch fractions) and mark wood accurately

Read a tape measure in millimetres and in inch fractions, use the sliding hook, mark with a V, draw square lines, check a corner with the 3-4-5 rule and check a level. Practise on a drawn tape with endless random readings.

Keep it one tap away for everyday use.

Bookmark Measure and mark?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Read tape
  2. Mark a V
  3. Check square
Nothing is uploadedWorks offline once open

Stay safe

  • Let a tape blade wind back slowly with your hand on it. A fast tape can snap back and cut fingers.
  • Keep pencils and knives sharp, and cover the knife blade when you put it down.
  • Before you mark a wall for drilling, check for hidden cables and pipes. If unsure, call an electrician or plumber.

What you need

  • Tape measure
  • Sharp pencil
  • Combination square
  • Spirit level
  • Utility knife (for fine marks)
  • Straight edge or long level

Step by step

  1. 121314 127 mm

    Read a metric tape

    The big numbers are centimetres. Each small mark is 1 millimetre, and the longer mark halfway is 5 mm. Read the last number, times 10, then count the small marks past it: 12 cm and 7 marks is 127 mm.

    Work in millimetres for woodwork. "1270 mm" is clearer than "1.27 m" or "127 cm".

  2. 561/21/43/41/8 marks1/16 marks

    Read inch fractions

    Each inch is cut in half, then quarters, eighths and sixteenths. The longer the mark, the bigger the fraction: the longest is 1/2, then 1/4 and 3/4, then the eighths, and the shortest are sixteenths. Count sixteenths past the last inch and simplify: 6/16 is 3/8.

    Halve the top and bottom while both are even: 12/16 = 6/8 = 3/4.

  3. hooked: pulls outpushed: slides in

    The loose hook is meant to move

    The hook on the end slides by exactly its own thickness (about 1 mm). Hooked over an edge it pulls out; pushed against a wall it slides in. That way both readings start at true zero.

    Never bend the hook to "tighten" it. Keep it clean so it slides freely.

  4. 650650

    Measure twice, cut once

    Measure, mark, then measure again from the same end before you cut. Say the number out loud or write it on the wood. Where you can, hold the piece in place and mark it straight from the job instead of using numbers at all.

    Use the same tape for the whole job. Two tapes can differ by a millimetre or two.

  5. waste

    Mark with a V

    A single dash is hard to find again and can be read from either side. Draw a small V (a "crow's foot") with its point exactly on the measurement. Use a sharp pencil, or a knife for fine work.

    Put a cross on the waste side, then cut on the waste side of the line so the piece keeps its full length.

  6. Draw a square line

    Press the square's stock (the heavy part) firmly against a straight, smooth edge of the board. Put the pencil point on your V, slide the blade up to touch it, and draw along the blade.

    Carry the line round all the faces you will see, so the saw has a guide on every side.

  7. 345

    Check a corner with 3-4-5

    For a big corner (a frame, a deck, a shed base), measure 3 units along one side and 4 along the other, and mark both. If the corner is square, the diagonal between the marks is exactly 5. Use 300, 400, 500 mm or 3, 4, 5 ft, or double it for more accuracy.

    On a rectangle, the two diagonals should also be equal. Try the checker below.

  8. Use and check a level

    The bubble between the two lines means level (or plumb, held upright). To check the level itself, read it, turn it end for end on the same spot and read again. If the bubble moves, the level is out: do not trust it.

    For long runs, rest the level on a straight board to span bumps.

Read the tape

mm

Type the reading in whole millimetres, for example 127.

3-4-5 square checker

Measure along both sides of the corner, mark, then measure the diagonal between the marks. Use any one unit for all three.

Call a professional when

  • You are marking holes in a wall and are not sure where cables or pipes run: call an electrician or plumber to check.
  • You are setting out foundations, a building or anything that needs planning permission: a surveyor or builder sets it out.
  • Floors, walls or door frames are far out of square or level, which can point to movement in the building.

Check yourself

What it does

Accurate work starts with accurate marks. This lesson teaches you to read a tape measure in millimetres and in inch fractions, why the hook on the end is loose on purpose, how to mark with a V, how to draw a line square across a board, how to check a big corner with the 3-4-5 rule, and how to check that a spirit level is telling the truth. Eight illustrated steps can be ticked as you go.

Two activities let you practise. Read the tape draws a piece of tape with a pencil mark at a random length: type the reading in millimetres, or switch to inches and type it as a fraction such as 5 3/8. Each answer shows how to read it. The 3-4-5 square checker takes the two sides and the diagonal you measured and tells you whether the corner is square, and which way to push it if not.

It is the third lesson of the free Hand tools and safety course, after know your hand tools and workshop safety. With your measurements in hand, plan your boards with the cut list, or size a whole deck with the deck calculator.

How to use it

  1. Read the steps with a tape measure in your hand if you have one. Tick each step when you can do it.
  2. In Read the tape, choose metric or imperial, read where the pencil mark is and press Check. New length gives you another. Your score counts first answers only and is not saved.
  3. In the 3-4-5 square checker, type side A, side B and the diagonal, all in the same unit. The answer updates as you type.
  4. Take the quiz.

What the tape markings mean

  • Metric tape: the large numbers are centimetres. Every small mark is 1 mm and the mid mark is 5 mm. Many tapes also print a metre marker every 100 cm.
  • Inch tape: the numbers are inches. Between them, the longest mark is 1/2, then 1/4 and 3/4, then eighths, then the shortest sixteenths. Many tapes mark every 16 inches (a common stud spacing) in a different way.
  • The hook: slides by its own thickness, so readings hooked over an edge and pushed against a wall both start at true zero.

Worked example

You are building a frame with sides of 1200 mm and 900 mm and want the corner square. You measure 600 mm along one side and 800 mm along the other (3-4-5 times 200) and mark both with a V. The diagonal between the marks reads 1004 mm. The checker says it should be 1000 mm: yours is 4 mm longer, so the corner is open at about 90.5°. You push the far ends of the frame a little closer together until the diagonal reads 1000 mm, then fix it.

On an inch tape, a mark that sits 6 small marks past 5 is 5 and 6/16 inches, which simplifies to 5 3/8 in.

FAQs

Why is my tape’s hook loose? It is designed to be. It moves by its own thickness so that both inside and outside measurements are right. Do not bend it.

What is the 3-4-5 rule? Pythagoras’ theorem in practice. A triangle with sides 3, 4 and 5 always has a right angle between the 3 and 4 sides. Any multiple works: 30-40-50 cm, 6-8-10 ft.

Should I use metric or imperial? Whichever your materials are sold in. Do not mix them in one job. Millimetres avoid fractions, which is why many woodworkers prefer them.

How accurate do I need to be? For rough framing, within 2 to 3 mm (1/8 in). For furniture and shelves that must fit, within 1 mm (1/32 in). Marking with a knife instead of a pencil helps.

Where the numbers come from

  • The 3-4-5 rule is Pythagoras' theorem: 3² + 4² = 5². The diagonal and angle in the checker are worked out with Pythagoras and the cosine rule. Tape markings follow common metric (centimetre numbers, millimetre marks) and imperial (sixteenth of an inch) tapes; some tapes differ. Drawings are fibub's own.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-16.

Change log for Measure and mark

  1. Hand tools and safety course: #L373 know your hand tools, #L374 workshop safety, #L375 measure and mark, #T1011 cut list Details on GitHub

Every change to fibub

Related tools

Deck calculator #T872 Count the deck boards, joists and screws or hidden clips for a deck from its size, board width, gap, the board lengths you can buy and joist spacing. Know your hand tools #L373 Learn the 13 tools in a basic home tool kit: what each one is for, how to hold it and the common mistake to avoid. Tap the tool wall to name them, tick the ones you have, and test yourself on which tool fits the job. Workshop safety #L374 Stay safe doing DIY at home: the right glasses, ear and dust protection, when not to wear gloves, clamping, cutting away from you, the 1 in 4 ladder rule, dust and fumes, small cuts and when to stop. Spot seven hazards in a workshop picture and test yourself. Cut list #T1011 Type the length of the boards you can buy, the saw kerf and the pieces you need. The cut list packs them onto the fewest boards, draws each board with its cuts and offcut, and gives the waste and a list to copy or print. Millimetres or inches. Saw a straight cut #L376 Saw a straight, square cut in wood with a handsaw in seven illustrated steps: mark a square line, clamp the work, cut on the waste side of the line, start with short strokes and let the saw do the work. Try the kerf sim to see why the side of the line matters. Change a flat tyre #L370 Change a flat car tyre onto the spare in eight illustrated steps: get safe, loosen the nuts, jack at the right point, swap the wheel and tighten in a star pattern. Tick each step, name the parts, and print the checklist for your glovebox.