How to fix a bike puncture: patch an inner tube step by step with pictures

Patch a bicycle inner tube in nine illustrated steps: take the wheel off, lever the tyre off, find the hole and the thorn, roughen, glue, patch and refit without pinching. Name the parts of a bike wheel and test yourself.

Keep it one tap away for everyday use.

Bookmark Fix a bike puncture?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Find hole
  2. Patch
  3. Refit
Nothing is uploadedWorks offline once open

Stay safe

  • Get off the road or cycle path first. Turn the bike upside down on its saddle and bars, or hang it up, somewhere out of the way.
  • Feel inside the tyre slowly with your fingertips: the thorn or glass that caused the puncture may still be there and is sharp.
  • Before you ride again, check the wheel is done up tight and the brakes work. A loose quick release can let a wheel fall out.
  • Puncture glue gives off fumes: use it in fresh air, put the lid back on and keep it away from flames.

What you need

  • Puncture repair kit (patches, glue, sandpaper)
  • 2 or 3 tyre levers
  • Pump that fits your valve
  • Spanner (15 mm) if the wheel has nuts
  • Chalk or a pen
  • Bowl of water (helpful)
  • Spare inner tube (optional)

Step by step

  1. Take the wheel off

    For a back wheel, change to the smallest rear sprocket first. Open the rim brake if it has a quick release. Then open the wheel's quick release lever (or undo the axle nuts, or unscrew a thru-axle) and lift the wheel out.

    Back wheel: pull the derailleur back a little so the chain lets go of the sprocket.

  2. PrestaSchrader

    Let the rest of the air out

    Presta (thin) valve: unscrew the little tip, then press it. Schrader (car-type) valve: press the pin in the middle. Squeeze the tyre all round so its edges drop into the dip in the middle of the rim.

  3. Lever one side off

    Opposite the valve, hook a tyre lever under the tyre's edge and pull it down; clip it to a spoke. Put a second lever in about 10 cm (4 in) away and pull. Then slide it round the rim until one side of the tyre is off.

    Never use a screwdriver: it can cut the tube and scratch the rim.

  4. Find the hole

    Pull the tube out, leaving the valve till last. Pump a little air in and listen and feel for a hiss, or pass it slowly through a bowl of water and look for bubbles. Mark the hole with chalk or pen.

    Two small holes side by side (a "snake bite") mean the tube was pinched: pump harder next time.

  5. Find what caused it

    Hold the tube against the tyre, with the valve at the valve hole, to see where the hole lines up. Feel slowly round the inside of the tyre there and pull out any thorn, glass or wire. Check the outside too.

    Skip this and the new patch will be punctured again within minutes.

  6. Roughen and glue

    Rub the tube round the hole with the sandpaper, over an area a bit bigger than the patch, until it looks dull. Spread a thin layer of glue over that area. Wait until the glue goes from shiny to dull and tacky, usually 3 to 5 minutes.

    Self-adhesive (glueless) patches skip the glue but still need the roughening.

  7. Stick the patch on

    Peel the foil off the patch without touching its sticky side. Press it onto the glue, centred on the hole, and squeeze hard from the middle outwards for a minute. Leave the thin clear film on top if your kit says so.

  8. Put it back without pinching

    Pump just enough air in to give the tube its shape. Push the valve through the rim, tuck the tube into the tyre all round, then push the tyre's edge back on with your thumbs, finishing at the valve. Try not to use levers here.

    Push the valve up into the tyre and back out, and look all round: no tube should show under the tyre edge.

  9. 50-85 PSI

    Pump up and refit

    Pump to a pressure inside the range printed on the tyre's side. Refit the wheel, close the quick release firmly (or tighten the nuts), close the brake and spin the wheel to check it runs straight and the brakes work.

Name the parts

Put the steps in order

Call a professional when

  • The hole is next to the valve, is a long split, or the valve itself leaks: fit a new tube instead.
  • The tyre has a cut you can see the tube through, or the tyre edge or rim is damaged: a bike shop can advise.
  • The bike has hydraulic disc brakes and you squeezed the lever with the wheel out, or the gears or brakes do not work properly after refitting.
  • It is a tubeless or e-bike hub-motor wheel and you are not sure how it comes out.

Check yourself

What it does

This lesson shows you how to mend a punctured bicycle inner tube with a patch, the job every rider needs sooner or later. A puncture kit costs very little, fits in a saddle bag, and a patched tube is as good as new. The nine steps each have a drawing and a Done tick, so you can follow along with the bike in front of you. The wheel picture teaches the names of the parts (tyre, inner tube, valve, rim, spokes, hub, quick release, patch and tyre lever), and you can press Test me to check you remember them. A put-in-order activity and a short quiz make sure the order sticks, and Print checklist gives you a paper copy for the shed.

It is the third lesson of the free Tyres and punctures course. For a car, see plugging a tubeless car tyre or changing a flat car tyre, and use tyre pressure to convert psi and bar.

How to use it

  1. Read Stay safe and get the bike out of the way of traffic.
  2. Work down the steps and tick each one when it is done. Ticks are kept only if you tick Remember my ticks on this device, and Clear ticks removes them.
  3. Tap the parts of the wheel picture to learn their names, then press Test me.
  4. Put the steps in order, then take the quiz.

What each part does

  • Tyre: the outer rubber case that grips the road. Its side shows the size and the pressure range.
  • Inner tube: the rubber ring inside that holds the air. This is what you patch.
  • Valve: Presta is thin, with a small tip you unscrew before pumping; Schrader is the wider car-type valve. Your pump must fit yours (many pumps fit both).
  • Rim: the metal hoop the tyre sits on. Spokes hold it true; the hub turns on bearings in the middle.
  • Quick release: a lever that clamps the wheel in the frame. Some bikes have axle nuts or a thru-axle instead.
  • Tyre lever: a flat plastic lever that lifts the tyre edge off the rim.

Worked example

Your back tyre goes soft on the way home. You change to the smallest sprocket, open the quick release and lift the wheel out. You let the rest of the air out, hook two levers under the tyre opposite the valve, and run one round the rim. Pumping the tube a little, you hear a hiss and mark the hole. Lining the tube up with the tyre, you find a small thorn in the tread and pull it out. You sand round the hole, spread thin glue, wait four minutes until it goes dull, and press the patch on hard for a minute. With a little air in the tube you tuck it in and thumb the tyre back on, finishing at the valve. You pump to 60 psi, inside the 50 to 85 psi printed on the tyre, refit the wheel, and check the brakes.

FAQs

Can I ride on it straight away? Yes, once the patch has been pressed on firmly. Glued patches bond more fully over the next hour.

Should I just fit a new tube? On the roadside it is quicker. Patch the old one at home and carry it as your spare.

Why does my tyre keep going flat? Usually something is still stuck in the tyre, a spoke end is poking through the rim tape, or the tube was pinched while refitting.

What about tubeless bike tyres? They are sealed with liquid sealant and mended with plugs, more like a car tyre. Follow the tyre maker’s instructions.

Where the numbers come from

  • Steps follow the general instructions printed in bicycle puncture repair kits and the advice of cycling organisations and bike makers' manuals (find and remove the cause, roughen, let the glue go tacky, refit without pinching, pump within the range printed on the tyre). Always follow your own kit's instructions. Drawings are fibub's own.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-16.

Change log for Fix a bike puncture

  1. Tyres and punctures: #L371 plug a tyre puncture, #L372 fix a bike puncture, #T1010 wheel nut torque Details on GitHub

Every change to fibub

Related tools