How to build and put up a simple wall shelf: plan, cut, sand, fix brackets and hang it level

Make a wooden wall shelf from one board and two brackets in nine illustrated steps: plan the size and load, cut and sand the board, screw on the brackets, finish it and hang it level. Label the parts, put the steps in order and check yourself.

Keep it one tap away for everyday use.

Bookmark Build a simple shelf?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Plan
  2. Make
  3. Hang
Nothing is uploadedWorks offline once open

Stay safe

  • Before you drill a wall, check for hidden cables and pipes with a detector, and never drill straight above, below or beside a switch or socket. If you hit a cable or pipe, stop and call an electrician or plumber.
  • Wear safety glasses for sawing, drilling and sanding, and a dust mask for sanding and drilling masonry.
  • Use a stable step ladder, not a chair, and have a helper hold the shelf while you mark.
  • Do not put a heavy shelf above a bed, cot or seat, and keep heavy things low.

What you need

  • Shelf board
  • 2 shelf brackets
  • Short screws for the board
  • Wall screws and plugs for your wall
  • Tape measure and pencil
  • Saw and square
  • Drill and bits
  • Sandpaper (120 and 180)
  • Spirit level
  • Cable and pipe detector
  • Oil, wax or paint
  • Safety glasses

Step by step

  1. length depth

    Plan it

    Decide the length, the depth and what will go on it. Books need about 200 to 250 mm (8 to 10 in) depth and weigh roughly 20 to 25 kg per metre of shelf. Find where on the wall it will go.

    Check the weight on each wall screw with the shelf load tool.

  2. Make a cut list and buy

    Write down each part and its size: one board, two brackets, short screws for the board, and wall screws and plugs that suit your wall. Buy the board a little longer than you need.

    Many timber yards will cut the board to length for you.

  3. Cut to length

    Square a line across, mark the waste side and cut on it, as in the Saw a straight cut lesson. Support the offcut at the end.

    Measure twice, cut once.

  4. Sand it

    Sand the faces and edges with 120 grit, then 180, always along the grain. Round off the sharp corners a little so they do not chip.

    Wrap the paper round a block to keep surfaces flat.

  5. ⅙⅙

    Mark the brackets

    Turn the board upside down. Set each bracket the same distance in from its end, about a sixth of the length, with its upright arm flush with the back edge. Mark the holes and drill small pilot holes.

    Set in from the ends, the board sags less in the middle.

  6. 18

    Screw on the brackets

    Screw the brackets to the underside. These screws must be shorter than the board is thick: for an 18 mm board, use 12 to 16 mm screws so the tips never poke through the top.

    Check the brackets are square to the back edge before the last screw.

  7. Finish it

    Wipe off the dust, then oil, wax, varnish or paint the board. Follow the tin for drying time and give it two thin coats rather than one thick one.

    Work in a ventilated room and lay oily rags flat outside to dry: they can catch fire if bundled up.

  8. Check the wall and mark a level line

    Scan the area with a cable and pipe detector. On a hollow wall, find a stud for at least one bracket. Hold the shelf in place, put a spirit level on it and mark the holes through the brackets.

    See What's in your wall in the Wall fixings course.

  9. Drill, plug and hang

    Drill the holes with the right bit for your wall, push in plugs that suit it (none into a stud), and screw the shelf up. Check level again, then load it a little at a time.

    Which plug? See Pick the right wall plug.

Name the parts

Put the steps in order

Call a professional when

  • The detector finds a cable or pipe where you want to drill, or you drill into one: stop and call an electrician or plumber.
  • The shelf will carry a lot of weight (a full bookcase run, a TV, a fish tank) or hang over a bed, cot or seat.
  • The wall crumbles, the plugs spin, or you cannot tell what the wall is made of.
  • You rent your home: check with the landlord before drilling.

Check yourself

What it does

This is a project lesson: you build one real wooden shelf from a single board and two metal brackets, and put it up on a wall. It brings together the two skills from earlier in the course. Nine illustrated steps take you from planning to a level, loaded shelf, each with a Done tick so you can follow along over an afternoon. Tap the picture to learn the parts of a shelf, put the steps in order, and take the short quiz before you start drilling.

It is the last lesson of the free Light carpentry course. Cut the board with a straight saw cut, fix the brackets as in drilling and screwing wood, and check the screws in the wall can take the weight with shelf load.

How to use it

  1. Read the Stay safe box. Before you drill any wall, check for hidden cables and pipes.
  2. Work down the steps and tick each one. Ticks stay only on this page unless you tick Remember my ticks on this device.
  3. Tap the parts in the picture, then press Test me to see if you know them.
  4. Put the steps in order, take the quiz, and print the checklist to take to the wall.

What each part does

  • Shelf board: solid pine or oak, or a faced board such as plywood or MDF, usually 18 to 22 mm (about ¾ to ⅞ in) thick. Thicker and shorter spans sag less under books.
  • Brackets: carry the board and pass its weight to the wall. Longer vertical arms grip the wall better, because the top screw has a longer lever.
  • Screws: short ones up into the board (shorter than the board is thick, so they do not poke through), and longer ones into the wall.
  • Wall plug: a plastic or metal sleeve that lets a screw grip brick, block or plasterboard. Into a timber stud you use a wood screw with no plug.
  • Stud: an upright timber or metal post inside a hollow wall. Screwing into a stud is the strongest fixing on a hollow wall.
  • Spirit level: the bubble sits between the lines when the shelf is level.

Worked example

You want a 800 mm (about 31½ in) shelf, 200 mm (8 in) deep, for paperbacks. Books weigh roughly 20 to 25 kg per metre of shelf, so about 20 kg here. You buy an 18 mm pine board, two 200 mm brackets with 150 mm upright arms and a pack of 16 mm screws for the board. You cut the board to 800 mm on the waste side of the line and sand it. You set the brackets 130 mm in from each end (about a sixth of the length), drill 2 mm pilots and screw them on. After two coats of oil you mark a level line, check for cables and pipes, find a stud for one bracket, use the right plugs for the other, and screw it up. With about 21.5 kg on it (books plus the board) and the wall screws 120 mm apart on each upright arm, the shelf load tool shows each top screw is pulled out with about 9 kg, well within a good fixing.

FAQs

How far apart should brackets be? For an 18 mm board with books, about 400 to 600 mm (16 to 24 in) apart, set in from each end by about a sixth of the length. Heavier loads or thinner boards need them closer.

Can I use the screws that came with the brackets? For the board, often yes. For the wall, packet screws and plugs are often too short or too weak: pick the fixing for your wall type.

Why fix the brackets to the board first? It is easier to get them square and in line on the bench. Then you only need to level one thing on the wall. Some people fix the brackets to the wall first and screw the board down after; both work.

What wall fixings should I use? That depends on the wall. The Wall fixings lessons what's in your wall and pick the right wall plug cover it.

Where the numbers come from

  • Steps follow general woodworking and DIY practice (brackets set in from the ends, screws into the board shorter than its thickness, fixings chosen for the wall, level checked with a spirit level). Drawings are fibub's own.
  • Bracket spacing and load figures are rough guides; the bracket and wall-fixing makers' ratings come first.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-16.

Change log for Build a simple shelf

  1. Home skills: link hand tools lessons and cut list with carpentry Details on GitHub
  2. Home skills: cross-link carpentry, wall fixings and machines lessons Details on GitHub
  3. Light carpentry course: saw a straight cut (#L376), drill and screw wood (#L377), build a simple shelf (#L378), shelf load (#T1012) Details on GitHub

Every change to fibub

Related tools

Cut list #T1011 Type the length of the boards you can buy, the saw kerf and the pieces you need. The cut list packs them onto the fewest boards, draws each board with its cuts and offcut, and gives the waste and a list to copy or print. Millimetres or inches. Saw a straight cut #L376 Saw a straight, square cut in wood with a handsaw in seven illustrated steps: mark a square line, clamp the work, cut on the waste side of the line, start with short strokes and let the saw do the work. Try the kerf sim to see why the side of the line matters. Drill and screw wood #L377 Join two pieces of wood with screws that pull tight and do not split the wood: pick the screw length, drill a clearance hole and a pilot hole, countersink, set the drill's clutch and drive straight. The screw picker suggests length, gauge and drill sizes. Shelf load #T1012 Work out how hard a wall shelf pulls on each screw. Type what goes on it (or pick books, plates or plants), the shelf depth and the bracket size, and see the pull-out and downward load per screw in kg and newtons, compared with your wall fixing's rating, with a side-view drawing of the forces. What's in your wall #L379 Learn to tell drywall, lath and plaster, brick, block and concrete apart, find studs, and spot where hidden cables and pipes run before you drill. Tap drill spots on a wall to test yourself. Pick the right wall plug #L380 Choose between plastic plugs, hollow-wall anchors, toggles, masonry screws and resin for drywall, plaster, brick, block or concrete. A picker gives the fixing and drill bit for your wall and weight, plus the steps to fit a plug.