What's in my wall? Find studs, tell wall types apart and avoid hidden cables and pipes

Learn to tell drywall, lath and plaster, brick, block and concrete apart, find studs, and spot where hidden cables and pipes run before you drill. Tap drill spots on a wall to test yourself.

Keep it one tap away for everyday use.

Bookmark What's in your wall?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Wall type
  2. Find studs
  3. Safe spot
Nothing is uploadedWorks offline once open

Stay safe

  • Never drill straight above, below or beside a light switch or socket: cables run from them in straight lines.
  • Check for cables and pipes with a detector before every hole, and still drill with care: detectors miss things.
  • If you hit a cable or pipe, stop. Switch off the power at the main switch or the water at the stop tap, and call an electrician or plumber. Never try to repair it yourself.
  • Wear safety glasses when you drill, and keep children and pets away.

What you need

  • Stud, cable and pipe detector
  • Small strong magnet
  • Tape measure
  • Pencil
  • Masking tape
  • Torch
  • Thin drill bit (3 mm)
  • Safety glasses

Wall types at a glance

WallKnockTest-hole dustFound in
Drywall or plasterboard on wood studsHollow, solid over studsWhite, then wood shavings on a studMost North American homes, newer UK inside walls
Drywall on metal studsHollow, ringing over studsWhite, bit skids on thin metalFlats, offices, newer builds
Lath and plasterDull, a bit hollowWhite or grey plaster, then woodOlder houses (before about 1950)
Solid brickSolid, dead soundRed or orangeUK, India, Gulf and older homes
ConcreteSolid, very hard to drillGrey, fineFlats, towers, newer homes in India and the Gulf
Breeze, cinder or aircrete blockSolid (dense) or softGrey (dense) or white and powdery (aircrete)Modern UK houses, basements, garages

Tiles can cover any of these. Look at an edge, a switch plate or the inside of a cupboard to see what is under them.

Step by step

  1. Knock on the wall

    Knock with a knuckle as you move along. A hollow, drum-like sound means a stud wall (drywall, plasterboard or lath). A dull, solid sound everywhere means brick, block or concrete.

    On a hollow wall the sound goes solid every 400 mm (16 in) or so: those are the studs.

  2. Look at the dust

    In a spot you have already checked for cables, drill a tiny 3 mm test hole with tape-stuck paper below it. White dust then nothing means hollow board. Red or orange means brick. Fine grey means concrete or dense block. Wood shavings mean you hit a stud.

    Choose a spot that a picture or shelf will hide later.

  3. 400 mm

    Find the studs

    Slide a stud finder slowly across the wall and mark each edge it finds. Studs are usually 400 mm (16 in) apart, sometimes 600 mm (24 in). A small magnet sticks to the screws or nails that hold the board to each stud.

    Nail heads in the skirting board (baseboard) usually line up with the studs.

  4. Picture the cables

    Cables usually run straight up or down from switches, sockets and lights, and sometimes straight across between them. Treat those lines as no-drill zones, all the way to the ceiling and floor.

    In the UK, cables should be within 150 mm of the ceiling or a corner, or in line with a switch or socket ("safe zones"). North American codes differ. Either way, cables can be anywhere in old or DIY wiring: check your local rules and always use a detector.

  5. Picture the pipes

    Water and heating pipes run to radiators, sinks, baths, toilets and boilers, often straight up from the floor or down from the ceiling. Keep clear of the lines above and below them, and of any wall behind a kitchen or bathroom.

    Gas pipes run to the cooker, boiler or fire. Never drill near them; for any gas pipe work call a registered gas engineer.

  6. Scan, then mark the spot

    Run a cable and pipe detector over the spot and about 30 cm (12 in) around it, both up and down and side to side. When it is clear, mark the hole with a small pencil cross on masking tape.

    Detectors find live cables better than dead ones. They can miss cables deep in a wall, so the "no drill" lines still apply.

  7. Drill only as deep as you need

    Wrap tape round the bit to show the depth: the plug's length plus a few millimetres. In a hollow wall, stop as soon as the bit goes through the board. If the bit suddenly hits something hard or soft and odd, stop and check.

    Hit a cable or pipe? Stop, switch off at the main switch or stop tap, and call an electrician or plumber.

Safe to drill here?

This wall is shown as a detector might see it: dashed lines are studs, cables and a pipe. Tap each numbered spot to see if it is safe, then press Test me.

switch socket radiator 1 2 3 4 5 6

Call a professional when

  • You hit, nick or see a cable: switch off at the main switch and call an electrician. Never tape or mend it yourself.
  • Water appears from the hole: turn off the stop tap and call a plumber. Leave the bit or a screw in the hole for now, as it can slow the leak.
  • You smell gas: leave, do not use switches, and call the gas emergency number from outside.
  • You cannot tell what the wall is, or it is a fire-rated, party or structural wall in a flat: ask the building manager.

Check yourself

What it does

Before you hang anything, you need to know two things: what the wall is made of, and what is hidden inside it. This lesson shows you how to tell the common wall types apart with a knock, a magnet and a tiny test hole, how to find the wooden or metal studs in a hollow wall, and where electric cables and water pipes usually run so you can keep your drill well away from them. The wall picture lets you tap six drill spots and find out which are safe, then test yourself.

It is the first lesson of the free Wall fixings course. Once you know your wall, choose the fixing with Pick the right wall plug, then put it to use in Hang a picture or mirror.

How to use it

  1. Read the Stay safe box. The most important rule: never drill straight above, below or beside a switch or socket.
  2. Look at the wall types table, then work down the steps with the real wall in front of you. Tick each one when it is done. Ticks are not saved unless you tick Remember my ticks on this device.
  3. In Safe to drill here?, tap each numbered spot to see why it is safe or dangerous. Press Test me to be asked for each one.
  4. Take the quiz. Press Print checklist for a paper copy to keep with your drill.

What each wall type means for you

  • Drywall or plasterboard on studs: a thin board on a frame of wood or metal studs. Light things can go in the board with a hollow-wall fixing; heavy things should screw into a stud.
  • Lath and plaster: older houses. Plaster over thin wooden strips. It can crack and crumble, so drill gently with the hammer off.
  • Solid brick: strong. Plastic plugs hold well. Drill into the brick, not the soft mortar between bricks.
  • Concrete: very strong but hard to drill. You need a hammer drill. Stop if you hit steel reinforcing bar.
  • Block: dense breeze or cinder block behaves like brick, though some have hollow cores. Lightweight aircrete is soft and needs special plugs.
  • Tiles: a layer over any of the above. Drill the tile with a tile bit first, then the wall behind.

Worked example

You want to hang a mirror on a living room wall. You knock along it: hollow, with a solid patch every 40 cm or so. A magnet sticks to a line of screw heads 40 cm from the corner, and your stud finder agrees. So it is plasterboard on studs. There is a light switch by the door, 1 m from the corner, so you keep clear of the line straight above and below it and the line straight across at its height. The detector shows nothing around your spot 20 cm left of the second stud. You mark it on masking tape and choose a hollow-wall fixing, or move the mirror so its fixings hit the stud.

FAQs

Can I trust a stud finder? Mostly, on plain drywall. Lath, foil-backed board and tiles can confuse them. Check with a magnet or a tiny test hole hidden behind where the item will go.

Do cables really always run straight? They should, but old or DIY wiring can go anywhere. Treat the straight lines as a minimum and scan every spot with a detector.

What about the UK safe zones in other countries? The 150 mm and in-line zones are a UK rule. The US and Canadian codes protect cables differently, for example with steel plates where cables pass close to the face of a stud. Check your local rules.

How deep can cables be? Some are just under the surface. A depth stop on the bit and a detector both help, but nothing replaces keeping away from the danger lines.

Where the numbers come from

  • Wall types and test methods follow common DIY guidance from building-product makers and home-improvement guides. Drawings are fibub's own.
  • UK cable safe zones: BS 7671 (IET Wiring Regulations), regulation 522.6, as summarised in IET and electrical-safety charity guidance; checked 2026-11-16. Rules differ in other countries (for example the US and Canadian electrical codes); check your local rules.
  • Stud spacing: 400 mm (16 in) or 600 mm (24 in) centres are the common spacings in UK and North American timber framing.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-16.

Change log for What's in your wall

  1. Learn: Wall fixings course (#L379 What's in your wall, #L380 Pick the right wall plug, #L381 Hang a picture or mirror) Details on GitHub

Every change to fibub

Related tools