Shelf load calculator: how much pull and weight each wall screw takes on a bracket shelf

Work out how hard a wall shelf pulls on each screw. Type what goes on it (or pick books, plates or plants), the shelf depth and the bracket size, and see the pull-out and downward load per screw in kg and newtons, compared with your wall fixing's rating, with a side-view drawing of the forces.

Keep it one tap away for everyday use.

Bookmark Shelf load?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Load
  2. Brackets
  3. Per screw
Nothing is uploadedWorks offline once open

What's on it

Shelf and brackets

Measure the height between the centres of the top and bottom screw holes on the bracket's upright arm.

Your fixing

Per screw

    A rough guide from simple statics: it ignores the bracket bending, screws at an angle and how sound the wall is. The fixing maker's rating always wins. Put heavy loads into studs or solid masonry, never plasterboard alone, and check for cables and pipes before you drill. Nothing you type leaves this page.

    What it does

    This shelf load calculator shows how hard a shelf on two or more brackets pulls on each screw in the wall. Most people think only about the weight pressing down, but the real job of the top screw on each bracket is to stop the bracket tipping forward: the deeper the shelf and the shorter the bracket, the harder it is pulled straight out of the wall. Type what goes on the shelf, its depth and the bracket size, and you get the pull-out and downward load per screw in kilograms and newtons, a check against your wall fixing’s rating with a safety factor, and a side-view drawing of the forces.

    To make and hang the shelf, follow the build a simple shelf lesson; for screwing the brackets to the board, see drill and screw wood.

    How to use it

    1. What’s on it: pick books, plates, plants or ornaments and type the shelf length, or choose “Type a weight” and enter the kilograms. Add the board and brackets.
    2. Where the weight sits: “spread evenly” puts it halfway back (half the depth). Choose “at the front edge” for things that overhang or get leaned on.
    3. Shelf and brackets: the depth from the wall, how many brackets, the height between the top and bottom wall screw of one bracket, and the screws per bracket.
    4. Your fixing: type the load per fixing from the packet or the maker’s table, and say whether it is a safe working load or a failure (ultimate) load. For a failure load, pick a safety factor.

    What each result means

    • Pull-out per top screw: the force pulling the top screw straight out of the wall. This is usually the one that fails, so it is the main result.
    • Down (shear) per screw: the weight shared by every wall screw, pushing down across it.
    • Combined on a top screw: the two together, because the top screw carries both.
    • Safety factor: how many times stronger than the load the fixing should be. Use 2 for light, well-known loads into solid masonry or studs, 3 for everyday shelves, and 4 for anything over people, things that get pulled on, or walls you are unsure about.

    Worked example

    An 800 mm shelf of paperbacks at about 25 kg per metre is 20 kg, plus 2 kg for the board and brackets: 22 kg, which is W = 22 × 9.81 = 216 N. The shelf is 250 mm deep, so the load acts 125 mm from the wall. Each of the two brackets has its two wall screws 200 mm apart. The top screws must hold 216 × 125 ÷ 200 = 135 N between them, so each top screw is pulled out with about 67 N, about 6.9 kg. Each of the four screws also carries 216 ÷ 4 = 54 N (5.5 kg) down. Your plugs are rated 25 kg at failure; with a safety factor of 3 that allows 8.3 kg per screw, so 6.9 kg is within it. Make the brackets taller (screws 300 mm apart) and the pull drops to 4.6 kg.

    FAQs

    Why does bracket height matter so much? The load’s turning effect is shared between the top screw and the bottom edge of the bracket, which pushes into the wall. Double the gap between them and the pull on the top screw halves.

    Which number on the fixing packet do I use? Packets for plasterboard fixings often give a recommended (safe) load, which already has a margin built in. Engineering tables often give the failure load, which needs a safety factor.

    Is this exact? No. It is a rough guide that ignores the bracket bending, screws at an angle and how good the wall is. Fixing makers’ ratings win, and heavy loads belong in studs or solid masonry.

    What about the shelf sagging? That is the board bending between the brackets, a different question; the beam deflection calculator can work it out.

    Where the numbers come from

    • Physics: a bracket tips about its bottom edge, so the top screws resist the turning effect of the load, F = W × lever arm ÷ the height between the top and bottom screws; every screw also carries its share of the weight downwards (shear). fibub's own working of standard statics; a rough guide that ignores the bracket bending and the screw's angle.
    • Weights per metre of shelf (books about 25 kg, plates and dishes about 30 kg, plants in pots about 15 kg, light ornaments about 8 kg) are fibub's rough estimates; weigh yours if in doubt.
    • Safety factors of 2 to 4 on a fixing's failure load are common rules of thumb in DIY and fixing makers' guidance. Fixing makers' published safe loads always come first.

    Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

    Last updated 2026-11-16.

    Change log for Shelf load

    1. Home skills: link hand tools lessons and cut list with carpentry Details on GitHub
    2. Light carpentry course: saw a straight cut (#L376), drill and screw wood (#L377), build a simple shelf (#L378), shelf load (#T1012) Details on GitHub

    Every change to fibub

    Related tools

    Beam deflection calculator #T438 Solve a simply supported, cantilever, fixed-fixed, propped, overhanging or continuous beam under any mix of point loads, uniform or sloping distributed loads and applied moments. Get the support reactions, shear force and bending moment diagrams, the deflected shape and largest deflection, and the bending and shear stress for a rectangle, round bar or tube, I-beam built from plates, or your own I and c. Cut list #T1011 Type the length of the boards you can buy, the saw kerf and the pieces you need. The cut list packs them onto the fewest boards, draws each board with its cuts and offcut, and gives the waste and a list to copy or print. Millimetres or inches. Saw a straight cut #L376 Saw a straight, square cut in wood with a handsaw in seven illustrated steps: mark a square line, clamp the work, cut on the waste side of the line, start with short strokes and let the saw do the work. Try the kerf sim to see why the side of the line matters. Drill and screw wood #L377 Join two pieces of wood with screws that pull tight and do not split the wood: pick the screw length, drill a clearance hole and a pilot hole, countersink, set the drill's clutch and drive straight. The screw picker suggests length, gauge and drill sizes. Build a simple shelf #L378 Make a wooden wall shelf from one board and two brackets in nine illustrated steps: plan the size and load, cut and sand the board, screw on the brackets, finish it and hang it level. Label the parts, put the steps in order and check yourself. Pick the right wall plug #L380 Choose between plastic plugs, hollow-wall anchors, toggles, masonry screws and resin for drywall, plaster, brick, block or concrete. A picker gives the fixing and drill bit for your wall and weight, plus the steps to fit a plug.