Home / Learn / Home skills / Pick the right wall plugTool #L380 (formerly #3014)

Which wall plug do I need? Pick the right plug, anchor or screw for your wall and weight

Choose between plastic plugs, hollow-wall anchors, toggles, masonry screws and resin for drywall, plaster, brick, block or concrete. A picker gives the fixing and drill bit for your wall and weight, plus the steps to fit a plug.

Keep it one tap away for everyday use.

Bookmark Pick the right wall plug?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Your wall
  2. Weight
  3. Fixing
Nothing is uploadedWorks offline once open

Stay safe

  • Check for hidden cables and pipes before every hole, and never drill in line with a switch or socket.
  • Wear safety glasses. Masonry dust and bits of plaster fly out of the hole.
  • Anything people pull on or lean on (grab rails, handrails, stair gates) or that could fall on someone (TVs, wall cupboards, heavy mirrors) must follow the maker's fixing instructions.
  • Unplug or remove the battery before changing a drill bit.

What you need

  • Drill (hammer setting for masonry)
  • Masonry, wood and tile bits
  • The right plugs or anchors
  • Screws to suit
  • Screwdriver
  • Pencil and masking tape
  • Cable and pipe detector
  • Bathroom scales
  • Safety glasses

Step by step

  1. Know your wall

    Find out if the wall is hollow (drywall, plasterboard, lath and plaster) or solid (brick, block, concrete), and where the studs are. The lesson before this one shows how.

  2. 78 − 70= 8 kg

    Weigh what you are hanging

    Stand on bathroom scales holding the item, then take away your own weight. For a shelf or cupboard, add what will go on it: books are heavy, about 20 kg (45 lb) per metre of shelf.

  3. Use a stud if you can

    A plain wood screw into a stud is stronger and simpler than any hollow-wall anchor. If the item can move a little to hit a stud, move it.

    For a shelf between studs, screw a timber batten across two studs, then fix the shelf to the batten.

  4. max 10 kg · 6 mm

    Choose the fixing, read the packet

    Use the picker below to see what usually fits your wall and weight. Then read the packet: it gives the drill bit size, the screw size and how much each fixing holds in each wall. The packet's rating wins.

    Use at least two fixings, so each one carries half or less.

  5. Drill the right hole

    Use the bit size on the packet. Mark the depth with tape: the plug's length plus about 5 mm. Hammer setting on only for brick, block and concrete; off for board, plaster and tiles. Keep the drill straight and level.

    Drilling through masking tape stops the bit skidding and the plaster chipping.

  6. Clean out and fit the plug

    Blow or vacuum the dust out of the hole. Push or tap the plug in until it sits flush with the wall. A plug sticking out will split; a plug pushed in too deep will not grip the surface.

  7. Screw in and test

    Drive the screw through the item or bracket into the plug until it is snug, then stop: too tight and the plug spins or the board crumbles. Give the item a firm pull down before you trust it.

    If a plug spins, take it out and use the next size up, or a different fixing.

Fixing picker

Drill bit
Why

    These are cautious rules of thumb, not product ratings. The weight limit printed on the packet, for your wall type, is the one to follow.

    Name the fixings

    Fit a plastic plug: put it in order

    Call a professional when

    • You are fixing a TV, large mirror or wall cupboard over a bed, sofa or where children play, and you are not sure the wall will hold it.
    • The item is very heavy (over 50 kg or 110 lb), or the wall crumbles, cracks or the plugs keep spinning.
    • You hit a cable or pipe: stop, switch off at the main switch or stop tap, and call an electrician or plumber.
    • You need a grab rail for someone who relies on it: a fitter or occupational therapist can advise.

    Check yourself

    What it does

    A wall plug only holds if it suits the wall and the weight. A plain plastic plug that grips tightly in brick does almost nothing in hollow plasterboard, and a small anchor that is fine for a clock will pull out under a loaded shelf. This lesson explains the main kinds of fixing and when to use each one, then gives you a picker: choose your wall, type the weight and say what you are hanging, and it suggests a fixing, the drill bit and a short reason why. You also put the steps for fitting a plastic plug in order, name six fixings from a picture and take a short quiz.

    It is the second lesson of the free Wall fixings course. Find out what your wall is made of first with What’s in your wall, then use what you pick here to hang a picture or mirror.

    How to use it

    1. Weigh the item (stand on bathroom scales holding it and take away your own weight). For shelves and cupboards, add what will go on them.
    2. In the Fixing picker, choose your wall, type the weight in kg or lb, and choose what kind of thing it is. Tick Tiles over the wall if there are tiles.
    3. Read the suggestion, then check the packet of the fixings you buy: its weight rating for your wall type wins.
    4. Follow the steps, tick them as you go, and try the order activity and quiz.

    What each fixing does

    • Plastic wall plug: for solid brick, dense block and concrete. The screw spreads the plug against the sides of the hole.
    • Self-drill drywall anchor: a wide-threaded plastic or zinc anchor that screws straight into plasterboard. Quick, for light things.
    • Metal hollow-wall anchor: a sleeve that squashes into wings behind the board as you tighten it. Good for medium loads in drywall.
    • Spring and gravity toggles: wings or a bar that open behind a hollow wall or lath and plaster.
    • Snap toggle: a steel bar on plastic straps that sits flat behind the board. One of the strongest hollow-wall fixings.
    • Wood screw into a stud: the best choice in any stud wall. No plug needed, just a pilot hole.
    • Masonry screws and frame fixings: grip brick and concrete much harder than plastic plugs, for heavier loads.
    • Resin (chemical) anchors: glue a threaded rod into the hole, for very heavy loads or soft block.

    Worked example

    You want to hang an 8 kg mirror on a plasterboard wall, and the spot is between two studs. In the picker you choose Drywall or plasterboard, between studs, type 8 kg and choose Hangs flat. It suggests a self-drill drywall anchor. You use two, so each carries about 4 kg, and the packet says each holds 10 kg in 12.5 mm board, so you are well inside the limit. Change the wall to Solid brick and it suggests a plastic plug with a 6 mm masonry bit, hammer on.

    FAQs

    Why does a shelf count as double? A shelf sticks out, so its weight levers the top fixings out of the wall. The picker counts it as twice its weight to allow for that.

    What do the plug colours mean? Many makers colour plugs by size (for example yellow, red, brown, blue), but the colours are not the same everywhere. Read the bit and screw size on the packet.

    Can I use a bigger screw to make a plug grip better? Only up to the size the packet says. Too big and the plug splits or the brick cracks.

    What if I hit the mortar joint in a brick wall? Mortar is soft and holds badly. Move the hole into the brick if you can, or use a longer plug or a masonry screw.

    Where the numbers come from

    • Fixing types, bit sizes and rough weight ranges follow common guidance from fixings makers' packets and catalogues; the picker's limits are cautious rules of thumb, fibub's own working, not product ratings. Always follow the rating on the packet for your wall type. Drawings are fibub's own.

    Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

    Last updated 2026-11-16.

    Change log for Pick the right wall plug

    1. Home skills: cross-link carpentry, wall fixings and machines lessons Details on GitHub
    2. Learn: Wall fixings course (#L379 What's in your wall, #L380 Pick the right wall plug, #L381 Hang a picture or mirror) Details on GitHub

    Every change to fibub

    Related tools

    Drywall calculator #T870 Count the drywall or plasterboard sheets for a room's walls and ceiling, with waste, plus rough amounts of screws, joint tape and compound. Build a simple shelf #L378 Make a wooden wall shelf from one board and two brackets in nine illustrated steps: plan the size and load, cut and sand the board, screw on the brackets, finish it and hang it level. Label the parts, put the steps in order and check yourself. Shelf load #T1012 Work out how hard a wall shelf pulls on each screw. Type what goes on it (or pick books, plates or plants), the shelf depth and the bracket size, and see the pull-out and downward load per screw in kg and newtons, compared with your wall fixing's rating, with a side-view drawing of the forces. What's in your wall #L379 Learn to tell drywall, lath and plaster, brick, block and concrete apart, find studs, and spot where hidden cables and pipes run before you drill. Tap drill spots on a wall to test yourself. Hang a picture or mirror #L381 Hang a picture or mirror straight and at the right height: where the centre goes, picture hooks vs D-rings vs a French cleat, and a calculator that tells you exactly where to put the hook from the frame size and wire drop. Change a flat tyre #L370 Change a flat car tyre onto the spare in eight illustrated steps: get safe, loosen the nuts, jack at the right point, swap the wheel and tighten in a star pattern. Tick each step, name the parts, and print the checklist for your glovebox.