Home / Learn / Physics / Levers in everyday toolsTool #L382 (formerly #3016)

Levers in everyday tools: claw hammer, wheel brace, pliers and wheelbarrow; class 1, 2 and 3 levers and moments

See why a claw hammer pulls nails, a long wheel brace undoes tight nuts and a wheelbarrow carries 80 kg. Slide your hand along the handle and watch the push you need change, sort tools into class 1, 2 and 3 levers, and check the principle of moments.

Keep it one tap away for everyday use.

Bookmark Levers in everyday tools?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Move hand
  2. See push
  3. Sort levers
Nothing is uploadedWorks offline once open

Stay safe

  • This lesson explains the physics. Try things only with hand tools on scrap wood, never on a running machine.
  • A long bar multiplies your push. A bolt, nail or bar can snap or slip suddenly: keep your face and fingers out of the line it would fly in.
  • Never add a pipe to a spanner or wheel brace to "get more leverage" on a bolt with a set tightness. Use a torque wrench.
  • Lift a loaded wheelbarrow with your legs, back straight, and keep loads you cannot hold out of it.

Things to look at

  • Claw hammer
  • Old nail in scrap wood
  • Pliers
  • Scissors
  • Bottle opener
  • Wheel brace or spanner
  • Wheelbarrow
  • Tape measure

The big ideas

  1. bigsmall

    Force × distance

    A lever turns about a pivot called the fulcrum. Its turning effect, the moment, is force × distance from the fulcrum. A lever balances when the moments match: effort × effort arm = load × load arm.

    So a small push far from the fulcrum can hold a big load close to it.

  2. Class 1: fulcrum in the middle

    The fulcrum sits between the load and your effort. A claw hammer pulling a nail is one: the head rocks on the wood, the nail is a few centimetres one side, your hand is 30 cm the other side.

    Also class 1: crowbars, pliers, scissors, a seesaw.

  3. Class 2: load in the middle

    The fulcrum is at one end and the load sits between it and you. A wheelbarrow, a bottle opener and a nutcracker work this way. The effort arm is always longer than the load arm, so you always need less force than the load.

  4. Class 3: effort in the middle

    Your effort is between the fulcrum and the load, as with tweezers, a shovel, a broom or your own forearm. You push harder than the load, but the far end moves further and faster.

    Class 3 levers trade force for speed and reach.

  5. r

    Longer handle, less push

    Spanners and wheel braces are levers that turn. The turning effect on the nut, the torque, is your push × the distance from the nut to your hand. Hold the end, not the middle, and you need half the push of holding halfway.

    That is also why a long bar can over-tighten or snap a bolt so easily.

  6. No free work

    If the effort arm is 8 times the load arm, you push with an eighth of the force, but your hand moves 8 times as far. Work (force × distance) in equals work out, less a bit lost to friction.

Try it: how hard do you push?

  • Slide your hand to the end of the hammer handle, then halfway. How does the push change?
  • Wheel brace at 110 N·m: what length lets you do it with about 250 N, roughly a firm push with your body weight?
  • Wheelbarrow: why are the handles so long?

Name the parts of a lever

Which class of lever is it?

Find the fulcrum first. In the middle: class 1. Load in the middle: class 2. Your effort in the middle: class 3.

    Leave it to a qualified millwright or technician when

    • The lever is part of a machine: brake arms, clutch levers, tensioners, press linkages. These need lock-out and trade training.
    • A bolt has a set tightness (wheels, engines, structures): use a torque wrench to the maker's figure, not a longer bar.
    • A seized or rusted fastener will not move with normal force, or the tool starts to bend.
    • Lifting heavy machinery with bars or jacks: that is rigging work with its own rules.

    Check yourself

    What it does

    Most hand tools in a toolbox are levers. This lesson shows the physics behind them: a lever turns about a pivot, the fulcrum, and its turning effect (the moment) is force × distance. Put a small push far from the fulcrum and it can hold a big load close to it. Six illustrated idea cards explain the three classes of lever and why a longer handle needs less push. In the sim you pick a claw hammer, a wheel brace or a wheelbarrow, slide your hand along the handle and see the push you need, drawn to scale with arrows. Then you name the parts of a lever on a hammer pulling a nail, sort nine tools into class 1, 2 and 3, and take a short quiz.

    It is lesson 2 of the free How machines work course, after the simple machines lab. For balancing moments on a beam try the moments lab, and for how tight a real bolt should be see the bolt torque.

    How to use it

    1. Read the Stay safe box. The lesson explains physics; it is not training to repair machines.
    2. Work through the idea cards. Tick Done on each one as you go (ticks are not kept unless you tick Remember my ticks on this device).
    3. In Try it, choose a tool. Move the hand distance slider and the load slider, and read the push you need under the picture. The line below it shows the sum.
    4. Tap the parts of the hammer picture, then press Test me.
    5. Sort the tools into classes, then take the quiz. Press New questions for a fresh set.

    What each class of lever means

    • Class 1, fulcrum in the middle: the load is on one side and your effort on the other. Claw hammers, crowbars, pliers and scissors. They can give a big force (long handle side) or more speed (long load side).
    • Class 2, load in the middle: the fulcrum is at one end and the load sits between it and you. Wheelbarrows, bottle openers and nutcrackers. The effort is always less than the load.
    • Class 3, effort in the middle: your push is between the fulcrum and the load. Tweezers, shovels, brooms and your forearm. You push harder than the load, but the far end moves further and faster.
    • Turning tools: a spanner or wheel brace is a lever that turns about the nut. The torque on the nut is your push × the distance to your hand.

    Worked example

    A nail needs 1,200 N to pull out of a plank. The claw holds it 4 cm from where the hammer head rocks on the wood, and your hand is 30 cm from that point. Moments: effort × 0.30 = 1,200 × 0.04, so the effort is 48 ÷ 0.30 = 160 N, about the force to hold up 16 kg. The mechanical advantage is 30 ÷ 4 = 7.5, so your hand moves 7.5 times as far as the nail. Hold the handle halfway, at 15 cm, and you need 320 N: twice as much.

    A wheel nut needs 110 N·m. With a 40 cm wheel brace the push is 110 ÷ 0.40 = 275 N. A 25 cm spanner would need 440 N.

    FAQs

    Is a longer bar always better? For pulling nails or prying, a longer handle needs less force. For bolts with a set tightness it is risky: you cannot feel how hard you are pulling, and you can stretch or snap the bolt. Use a torque wrench.

    Why does the sim ignore friction? To show the moments rule clearly. Real tools lose a little to friction at the pivot, so you need slightly more push than the sim shows.

    Is my arm a lever? Yes, a class 3 one: the elbow is the fulcrum, your biceps pulls just below it, and your hand holds the load further out. That is why holding a weight with a straight arm is so hard.

    What comes next? Belts and pulleys, which pass turning from one shaft to another, then bearings and friction.

    Where the numbers come from

    • The principle of moments (effort × effort arm = load × load arm), the three classes of lever and torque = force × distance: standard school physics found in any textbook. g = 9.8 m/s² (rounded).
    • Nail pull-out forces, wheel nut torques and wheelbarrow loads in the sim are typical made-up examples; check your car's handbook for its real wheel nut torque. Drawings are fibub's own.

    Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

    Last updated 2026-11-16.

    Change log for Levers in everyday tools

    1. Home skills: cross-link carpentry, wall fixings and machines lessons Details on GitHub
    2. Learn: How machines work lessons #L382 levers in tools, #L383 belts and pulleys, #L384 bearings and friction Details on GitHub

    Every change to fibub

    Related tools

    Bolt torque #T439 Work out the tightening torque for a target bolt preload (or the preload a torque gives) with the nut factor T = K F d or the thread and under-head friction split, the tensile stress area of ISO metric or UNC/UNF threads from the pitch, the bolt and clamped-part stiffness, the joint constant, the separation load and safety factors, with a joint diagram. Friction ramp #L11 Tilt a ramp, pick the surfaces, set the mass and push, and see at once whether the block stays, slides down or moves up, with the gravity, support, friction and push arrows drawn on it and the numbers worked out. Simple machines lab #L13 Lift a load with a lever, a pulley system of 1 to 4 strands, a ramp or a wheel and axle; see the effort you need, the mechanical advantage, the velocity ratio and the efficiency, and check that work out is never more than work in. Moments lab #L327 Place weights on a beam, move the pivot and see the moments on each side. Find out when it balances, which way it turns and what the pivot pushes back with. Wheel nut torque #T1010 See a typical wheel nut torque for your kind of vehicle or stud size, or type your handbook figure; convert N·m, lbf·ft and kgf·m; work out how hard to push on a brace of any length; and see the star order to tighten 4, 5, 6 or 8 nuts. Belts and pulleys #L383 Learn how a belt drive changes speed and torque (n1 × d1 = n2 × d2), how long a belt must be, why the small pulley slips first and why alignment and tension matter. Spin two pulleys at the right speeds, change their sizes and spacing, and see chains and sprockets too. Bearings and friction #L384 See why a ball bearing lets a flywheel coast for hours while a dry bush stops it in two minutes. Learn sliding and rolling friction, plain, ball and roller bearings, what grease does, why bearings fail and the warning signs, then name the parts of a ball bearing.