Home / Learn / Physics / Bearings and frictionTool #L384 (formerly #3018)

Bearings and friction: plain, ball and roller bearings, lubrication and why bearings fail

See why a ball bearing lets a flywheel coast for hours while a dry bush stops it in two minutes. Learn sliding and rolling friction, plain, ball and roller bearings, what grease does, why bearings fail and the warning signs, then name the parts of a ball bearing.

Keep it one tap away for everyday use.

Bookmark Bearings and friction?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Pick bearing
  2. Spin, coast
  3. Name parts
Nothing is uploadedWorks offline once open

Stay safe

  • This lesson explains the physics. It is not training to work on machines.
  • Never touch a turning shaft, coupling or flywheel. A flywheel stores energy and keeps spinning long after the power is off.
  • Bearings on machines are checked or changed only with the machine stopped, isolated and locked out by a trained person.
  • A failing bearing can be hot enough to burn. Do not grab a housing to "feel" it.

Where you see them

  • Skateboard wheels
  • Bicycle hubs
  • Fidget spinner
  • Electric fan
  • Washing machine drum
  • Car wheel hubs
  • Door hinges (plain)

The big ideas

  1. Sliding versus rolling

    Friction is the force that resists one surface moving over another. Sliding friction is large; rolling friction is much smaller, because a rolling ball or roller barely rubs. That is the whole idea of a bearing: let a shaft turn with as little friction as possible.

  2. Plain bearings (bushes)

    A plain bearing is a sleeve, often bronze or plastic, that the shaft turns inside. Dry, it rubs and wears. With oil or grease a thin film separates the metal parts; at speed the oil film can lift the shaft completely, so friction drops a long way.

    Simple, quiet, cheap and good with shock loads: door hinges, engine crankshafts, pumps.

  3. Ball and roller bearings

    Rolling bearings have an inner ring on the shaft, an outer ring in the housing, and balls or rollers between them held apart by a cage. Balls touch at tiny points: low friction, high speeds. Rollers touch along lines: they carry heavier loads.

  4. What lubrication does

    Oil or grease keeps the surfaces apart so they do not touch, carries heat away, and keeps out dirt and water. The amount matters: too little and parts rub; too much grease churns, gets hot and can push seals out.

    Always the grease type and amount the maker gives.

  5. Why bearings fail

    Most bearings are killed, not worn out: by dirt or water getting in, the wrong amount of grease, misalignment (a shaft or pulley out of line), overload (such as an over-tight belt) and rough fitting (hammering on the wrong ring).

  6. Warning signs

    A bearing on its way out usually gets noisier (rumble, grinding, squeal), hotter and shakier long before it seizes. Maintenance teams listen with instruments, check temperatures and measure vibration so they can plan a change before it breaks.

    Makers rate rolling bearings by L10 life: the running time 90 % of them reach. Try the bearing life tool.

Try it: spin a flywheel and let it coast

A 40 cm steel disc on a 25 mm shaft, held by two bearings. Pick a bearing, press Spin, and watch how long it coasts. Only bearing friction slows it here (no air drag), with friction torque T = μ × F × r.

BearingμCoasts forHeat at start
  • Compare a dry bush with a ball bearing. How many times longer does the ball bearing coast?
  • Add 2,000 N of belt pull. Why does every bearing stop sooner and get hotter? (This is what an over-tight belt does.)
  • Double the start speed. The coast time doubles, but the heat made at the start doubles too.

Name the parts of a ball bearing

Leave it to a qualified millwright or technician when

  • A bearing on a machine is noisy, hot, shaking or leaking grease: report it, do not keep running it.
  • A bearing needs greasing, changing or fitting. Wrong grease, too much grease or hammering it on can wreck a new bearing within hours.
  • Shafts, couplings or pulleys need aligning, or a machine needs vibration or temperature checks.
  • Anything on a running machine, or any guard has to come off.

Check yourself

What it does

Every turning shaft sits in bearings, and bearings are among the parts a millwright checks and changes most. This lesson explains the physics: sliding friction versus rolling friction, how plain (bush) bearings and ball and roller bearings work, what lubrication does, why bearings fail and the warning signs before they do. Six illustrated idea cards cover the ideas. In the sim you spin a 40 cm steel flywheel on a 25 mm shaft, choose a dry bush, an oiled bush, a ball bearing or a roller bearing, and watch it coast to a stop. Friction torque T = μ × F × r slows it, and the spin energy becomes heat in the bearing, shown as a glow. A table compares all four bearing types. You can then tap the parts of a ball bearing and take a short quiz.

It is lesson 4 of the free How machines work course, after belts and pulleys. For a real bearing’s rated life use the bearing life tool, and for friction on a slope try the friction ramp.

How to use it

  1. Read the Stay safe box. The lesson explains physics; it is not training to work on machines.
  2. Work through the idea cards, ticking Done as you go (kept only if you tick Remember my ticks on this device).
  3. In Try it, pick a bearing and press Spin and let go. Time runs faster than real life so slow coasts fit in about 15 seconds; the line under the picture says how much faster.
  4. Change the start speed, the flywheel mass and the extra side load (like the pull of a belt). The table updates for all four bearings.
  5. Tap the parts of the ball bearing, press Test me, then take the quiz.

What each bearing type means

  • Dry plain bush (μ about 0.15): metal rubbing on metal or plastic. Cheap and simple, but it wears and makes heat.
  • Oiled plain bush (μ about 0.02): an oil film keeps the surfaces mostly apart. At high speed a full film can make friction even lower.
  • Ball bearing (μ about 0.0015): balls roll between two rings. Low friction, good for high speeds and moderate loads.
  • Roller bearing (μ about 0.0011): cylinders roll instead of balls. Line contact carries heavier loads.

Worked example

The 20 kg flywheel spins at 1,000 rpm on a dry bush. Its weight is 20 × 9.8 = 196 N. Friction torque: 0.15 × 196 × 0.0125 = 0.37 N·m. The disc’s moment of inertia is ½ × 20 × 0.2² = 0.4 kg·m², so it slows by 0.37 ÷ 0.4 = 0.92 rad/s every second. Its start speed is 2π × 1,000 ÷ 60 = 104.7 rad/s, so it stops after 104.7 ÷ 0.92 = 114 s, about two minutes. On ball bearings μ is 100 times smaller, so it would coast 100 times longer, over 3 hours, if nothing else slowed it. Either way all 2,190 J of spin energy ends up as heat. At the start the dry bush makes 0.37 × 104.7 = 38 W of heat in a small spot, which is why dry bushes get hot.

FAQs

Does a real flywheel on ball bearings coast for three hours? No. Air drag and rubbing seals slow it much sooner. The sim leaves them out so you can compare the bearings themselves.

Why does more side load make the bearing hotter? Friction torque is μ × F × r, so doubling the load F doubles the friction and the heat. An over-tight belt does exactly this to motor bearings.

Is more grease better? No. Too much grease churns and overheats the bearing. Makers say how much to use and how often.

What is L10 life? The number of hours (or turns) that 90 % of a batch of identical bearings will reach under a given load. The bearing life tool works it out from the catalogue rating.

Where the numbers come from

  • Friction torque T = μ F r, moment of inertia of a solid disc I = ½ m R², constant deceleration α = T ÷ I and kinetic energy ½ I ω²: standard physics found in any textbook. g = 9.8 m/s² (rounded).
  • Friction coefficients are typical values: dry and oiled plain bushes from engineering friction tables; ball (about 0.0015) and cylindrical roller (about 0.0011) from the constant-coefficient estimate in rolling bearing makers' catalogues. Real values change with speed, load, grease, seals and temperature. Drawings are fibub's own.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-16.

Change log for Bearings and friction

  1. Learn: How machines work lessons #L382 levers in tools, #L383 belts and pulleys, #L384 bearings and friction Details on GitHub

Every change to fibub

Related tools

Moment of inertia #T639 Build a body from simple uniform parts (rod, disc or cylinder, tube, ring, sphere, shell, box, point mass, and holes), place each one relative to the axis, and get the total moment of inertia with every step shown, the radius of gyration, the centre of mass, the moment about it and the spin energy at any rpm. Bearing life #T442 Work out a rolling bearing's L10 life in revolutions and hours from its rating C and the equivalent load P = X Fr + Y Fa (your catalogue values), adjusted for reliability and aISO, or the C you need for a target life. Size a solid round shaft for combined bending and torsion in fatigue (DE-Goodman with your endurance limit) and statically (von Mises and maximum shear), or check the safety factors of a given diameter. Friction ramp #L11 Tilt a ramp, pick the surfaces, set the mass and push, and see at once whether the block stays, slides down or moves up, with the gravity, support, friction and push arrows drawn on it and the numbers worked out. Simple machines lab #L13 Lift a load with a lever, a pulley system of 1 to 4 strands, a ramp or a wheel and axle; see the effort you need, the mechanical advantage, the velocity ratio and the efficiency, and check that work out is never more than work in. Levers in everyday tools #L382 See why a claw hammer pulls nails, a long wheel brace undoes tight nuts and a wheelbarrow carries 80 kg. Slide your hand along the handle and watch the push you need change, sort tools into class 1, 2 and 3 levers, and check the principle of moments. Belts and pulleys #L383 Learn how a belt drive changes speed and torque (n1 × d1 = n2 × d2), how long a belt must be, why the small pulley slips first and why alignment and tension matter. Spin two pulleys at the right speeds, change their sizes and spacing, and see chains and sprockets too.