Home / Courses / Engineering entrance / Practice / Alternating current

Alternating current

Class 12 · 270 questions and templates for Engineering entrance, in order from warm-up to top rank. Check each answer, then read the full solution.

New to this topic? Read the lesson first: Alternating current.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    The rms value of an alternating current i=I0sin⁡ωt is
    1. I0/2
    2. I0/2
    3. 2I0
    4. 2I0/π
    Answer and solution

    Answer: B

    The rms value is the steady current that gives the same heating as the AC. Averaging i2R over a cycle gives 12I02R, so Irms=I0/2≈0.707I0. 2I0/π is the mean over half a cycle.
  2. NATWarm-up

    The rms value of the mains voltage is 230 V. Find its peak value (in V, nearest whole number).
    Answer and solution

    Answer: 325 V (±1)

    V0=2Vrms=1.414×230=325 V.
  3. MCQWarm-up

    The average value of a sinusoidal alternating current over one full cycle is
    1. zero
    2. I0/2
    3. 2I0/π
    4. I0/2
    Answer and solution

    Answer: A

    The positive half cycle cancels the negative half cycle exactly, so the mean over a full cycle is zero. This is why we use the rms value, which does not cancel.
  4. MCQWarm-up

    The reading of an AC ammeter or voltmeter in a house circuit is the
    1. peak value
    2. average value over a full cycle
    3. peak-to-peak value
    4. rms value
    Answer and solution

    Answer: D

    AC meters are calibrated to show the rms value, because that is what decides heating and power. The mains "230 V" is an rms value.
  5. NATWarm-up

    Mains supply has a frequency of 50 Hz. Find its time period (in ms).
    Answer and solution

    Answer: 20 ms

    T=1/f=1/50=0.02 s =20 ms.
  6. MCQWarm-up

    The SI unit of inductive reactance is
    1. henry
    2. farad
    3. ohm
    4. ohm per metre
    Answer and solution

    Answer: C

    Reactance is a voltage-to-current ratio, so it is measured in ohm, like resistance. Henry is the unit of inductance and farad of capacitance.
  7. NATWarm-up

    Find the inductive reactance of a 0.2 H inductor at 50 Hz (in Ω, 1 decimal).
    Answer and solution

    Answer: 62.8 Ω (±0.1)

    XL=ωL=2πfL=2π×50×0.2=62.83 Ω.
  8. NATWarm-up

    Find the capacitive reactance of a 50 μF capacitor at 50 Hz (in Ω, 1 decimal).
    Answer and solution

    Answer: 63.7 Ω (±0.1)

    XC=1ωC=12π×50×50×10−6=63.66 Ω.

    Why people get this wrong: Convert microfarad to farad: 50 μF = 50 × 10^-6 F.

  9. MCQWarm-up

    In a purely inductive AC circuit, the current
    1. leads the voltage by π/2
    2. lags the voltage by π/2
    3. is in phase with the voltage
    4. lags the voltage by π
    Answer and solution

    Answer: B

    The inductor's emf opposes any change of current, so the current reaches its peak a quarter cycle after the voltage. Remember: in an inductor the voltage leads (ELI the ICE man: E before I in L).
  10. MCQWarm-up

    In a purely capacitive AC circuit, the current
    1. leads the voltage by π/2
    2. lags the voltage by π/2
    3. is in phase with the voltage
    4. is zero all the time
    Answer and solution

    Answer: A

    The current is dq/dt=CdV/dt. It is maximum when the voltage is changing fastest, which is when the voltage is zero: a quarter cycle before the voltage peak. In a capacitor, current leads (ICE).
  11. MCQWarm-up

    In an AC circuit with only a resistor, the phase difference between voltage and current is
    1. π/2
    2. π/4
    3. π
    4. zero
    Answer and solution

    Answer: D

    By Ohm's law i=v/R at every instant, so the two rise and fall together: they are in phase.
  12. MCQWarm-up

    The resonant frequency of a series LCR circuit is
    1. 12πLC
    2. 2πLC
    3. 12πLC
    4. 12πLC
    Answer and solution

    Answer: C

    At resonance XL=XC, so ωL=1/ωC and ω0=1/LC, giving f0=12πLC.
  13. NATWarm-up

    A series LCR circuit has L=10 mH and C=10 μF. Find its resonant frequency (in Hz, nearest whole number).
    Answer and solution

    Answer: 503 Hz (±1)

    f0=12πLC. LC=10−2×10−5=10−7, LC=3.162×10−4 s. f0=12π×3.162×10−4=503 Hz.
  14. MCQWarm-up

    A step-up transformer has
    1. more turns in the primary than in the secondary
    2. more turns in the secondary than in the primary
    3. an equal number of turns in both coils
    4. a permanent magnet as its core
    Answer and solution

    Answer: B

    Vs/Vp=Ns/Np. To raise the voltage, the secondary needs more turns. A step-up transformer lowers the current in the same ratio.
  15. NATWarm-up

    A transformer has 1000 turns in its primary and 100 turns in its secondary. The primary is connected to a 220 V AC supply. Find the secondary voltage (in V).
    Answer and solution

    Answer: 22 V

    Vs=VpNsNp=220×1001000=22 V. It is a step-down transformer.
  16. MCQWarm-up

    A capacitor is connected to a steady DC source in series with a lamp. After the capacitor has charged, the lamp
    1. does not glow
    2. glows steadily
    3. glows brighter and brighter
    4. flickers
    Answer and solution

    Answer: A

    For DC, f=0 and XC=1/ωC→∞: a capacitor blocks steady current once it is charged. It passes AC.
  17. NATWarm-up

    A series circuit has a resistance of 30 Ω and a net reactance of 40 Ω. Find its impedance (in Ω).
    Answer and solution

    Answer: 50 Ω

    Z=R2+X2=302+402=2500=50 Ω.

    Why people get this wrong: Resistance and reactance add at right angles, not directly.

  18. MCQWarm-up

    The average power consumed by an ideal inductor connected to an AC source over a full cycle is
    1. 12V0I0
    2. VrmsIrms
    3. Irms2ωL
    4. zero
    Answer and solution

    Answer: D

    Energy goes into the magnetic field in one quarter cycle and comes back in the next. Here ϕ=90∘, so cos⁡ϕ=0 and Pav=VrmsIrmscos⁡ϕ=0.
  19. MCQWarm-up

    Electric power is sent over long distances at very high voltage mainly because
    1. the resistance of wire falls at high voltage
    2. high voltage travels faster in the wire
    3. the current is then small and the I2R loss in the wires is small
    4. transformers work only at high voltage
    Answer and solution

    Answer: C

    For a given power P=VI, a higher V means a smaller I. The loss in the wires is I2R=(P/V)2R, so doubling the voltage cuts the loss to a quarter.
  20. NATWarm-up

    The current in a circuit is i=4sin⁡(314t) ampere. Find its rms value (in A, 2 decimals).
    Answer and solution

    Answer: 2.83 A (±0.01)

    The peak value is I0=4 A, so Irms=4/2=2.83 A. (The 314 is ω, giving f=50 Hz.)
  21. MCQWarm-up

    A transformer will not work with a DC supply because
    1. DC has too low a voltage
    2. a steady current gives a constant flux and no emf in the secondary
    3. DC cannot flow in a coil
    4. the core would melt at once
    Answer and solution

    Answer: B

    Induction needs a changing flux. A steady DC produces a constant flux, so dΦ/dt=0 and no emf is induced in the secondary.
  22. NATStandard

    A voltage is v=311sin⁡(100πt) volt. Find its frequency (in Hz).
    Answer and solution

    Answer: 50 Hz

    Compare with v=V0sin⁡ωt: ω=100π rads−1, so f=ω/2π=50 Hz.
  23. NATStandard

    A voltage is v=2002sin⁡(314t) volt. Find its rms value (in V).
    Answer and solution

    Answer: 200 V

    The peak value is 2002 V, so Vrms=V0/2=200 V.
  24. NATStandard

    A 50 Hz current i=I0sin⁡ωt starts from zero at t=0. How long does it take to reach its rms value for the first time (in ms, 1 decimal)?
    Answer and solution

    Answer: 2.5 ms (±0.05)

    I0sin⁡ωt=I0/2 gives ωt=π/4, so t=T/8=20/8=2.5 ms.

    Why people get this wrong: The rms value is reached at 45 degrees of phase, not 90.

  25. NATStandard

    A heater of resistance 55 Ω is connected to a 220 V rms supply. Find the average power it consumes (in W).
    Answer and solution

    Answer: 880 W

    P=Vrms2/R=2202/55=880 W. The current is 220/55=4 A rms.
  26. NATStandard

    A coil of resistance 30 Ω and inductive reactance 40 Ω at 50 Hz is connected to 220 V, 50 Hz mains. Find the rms current (in A, 1 decimal).
    Answer and solution

    Answer: 4.4 A (±0.05)

    Z=302+402=50 Ω. Irms=V/Z=220/50=4.4 A.
  27. NATStandard

    For the same coil (R=30 Ω, XL=40 Ω), find the angle by which the current lags the applied voltage (in degrees, 1 decimal).
    Answer and solution

    Answer: 53.1 ° (±0.1)

    tan⁡ϕ=XL/R=40/30=1.333, so ϕ=53.1∘. The current lags the voltage by this angle.
  28. NATStandard

    For the same coil on 220 V mains (current 4.4 A), find the average power consumed (in W, nearest whole number).
    Answer and solution

    Answer: 581 W (±1)

    Only the resistance dissipates power: P=I2R=4.42×30=581 W. Check: VIcos⁡ϕ=220×4.4×0.6=580.8 W.
  29. NATStandard

    A 60 Ω resistor is in series with a capacitor of reactance 80 Ω across a 100 V rms supply. Find the rms current (in A).
    Answer and solution

    Answer: 1 A (±0.005)

    Z=602+802=100 Ω and I=100/100=1.00 A. The current leads the voltage with tan⁡ϕ=80/60.
  30. NATStandard

    A 100 μF capacitor is connected to a 220 V, 50 Hz supply. Find the rms current (in A, 2 decimals).
    Answer and solution

    Answer: 6.91 A (±0.01)

    I=V/XC=VωC=220×314.16×10−4=6.91 A.

← All topics