Touch screen test: check multi-touch, dead zones, pressure and stylus

Check your touch screen: see every finger with its number, how many touches it handles at once, pressure and stylus tilt, and find dead spots with a coverage grid. Nothing is stored.

Keep it one tap away for everyday use.

Bookmark Touch Test?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Touch
  2. Swipe
  3. Coverage
Nothing is uploadedWorks offline once open

Draw and count shows each finger with its number. Dead zones splits the screen into squares that fill as you swipe over them; any square that stays empty may be a dead spot.

Touch the area above with one or more fingers or a stylus. The page cannot scroll while your finger is on it. Nothing is stored or sent.

Touching now
0
Most at once
0
Device says it supports
–
Input type
–
Pressure
–
Contact size
–
Pen tilt
–
Grid
–
Screen covered
–

Pressure: many screens report a fixed 0.5 while touched, or 0, because they cannot sense force. Only some styluses and phones give real values. Contact size is often 1 or the same every time; it is up to the device.

What it does

The Touch Test shows a touch area where every finger is drawn as a ring with its own number. It tells you how many touches are down now, the most you have used at once, and what the device says it supports. It also reads the pressure, the contact size and, for a stylus, the pen’s tilt, whatever the screen reports.

A second mode, Dead zones, splits the area into a grid of squares that fill in as you swipe. Any square you cannot fill may be a dead spot on a cracked, worn or badly calibrated screen, and a percentage shows how much of the screen you have covered. It runs in your browser; nothing is stored or sent. Check the picture itself with the screen Test, a pointer with the mouse Test, and the phone’s motion hardware with the sensor Test.

How to test your touch screen

  1. Touch the area with one finger and draw. Add fingers one at a time and watch the ring numbers and the Most at once figure.
  2. Switch to Dead zones and press Clear. Swipe slowly back and forth until every square is filled; leave nothing out.
  3. Look for squares that stay white however many times you swipe over them.
  4. Use Full screen to test the edges and corners (not available on iPhone). Press Clear to start again.

What each part shows

  • Touching now / Most at once: fingers down right now, and the highest number seen together.
  • Device says it supports: the touch points the device reports. Many phones say 5 or 10; the real limit can be lower.
  • Input type: touch, stylus (pen) or mouse.
  • Pressure: 0 to 1. Many screens give a fixed 0.5, or 0, because they cannot sense force.
  • Contact size: the touch width and height in pixels. Often fixed or 1 on some devices.
  • Pen tilt: stylus lean in degrees, only for pens that report it.
  • Screen covered: how much of the grid you touched.

Worked example

On a tall phone the grid is 8 by 12, so 96 squares. If you swipe everywhere except one corner square, the test reads 95 of 96, or 99%. If that same square stays white after many tries in different directions, the touch layer there may be dead. Five fingers down read “Most at once 5”.

Touch problems

  • Phantom touches or lag: clean the screen, remove a thick screen protector, and try without a case.
  • A dead strip at the edge: some phones ignore edge touches on purpose to avoid accidental taps. Test it with a flat finger.
  • Fewer touches than expected: some screens drop touches when palms rest on the edge; try fingertips only.
  • The page will not scroll: it is blocked only while a finger is on the test area. Touch outside it to scroll.

FAQs

Why is the pressure always 0.5? Most touch screens cannot measure force, so browsers report a placeholder. Real values mostly come from styluses and a few phones.

Does it work on a laptop with a touch screen? Yes. A mouse draws too, one point at a time.

Does the dead-zone test prove a screen is broken? It shows where the screen did not register a touch. Also swipe slowly, because very fast strokes can skip squares even on a good screen.

Is anything recorded? No. Touches are drawn and forgotten; nothing is saved or sent.

Where the numbers come from

  • Touches come from pointer events (pointerType touch or pen): pointerId, clientX/Y, pressure, width, height, tiltX and tiltY. The device's own limit is navigator.maxTouchPoints.
  • Dead-zone coverage is the share of grid squares (8 x 12 on tall screens, 12 x 8 on wide ones) you touched, counted in src/lib/device/core.ts and checked in tests/device.mjs. The grid size is fibub's own choice.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-19.

Change log for Touch Test

  1. Add 13 device testers (#T1051-#T1063) and allow the microphone on audio tools Details on GitHub

Every change to fibub

Related tools