Mic test: check your microphone online, with a live level meter and playback

Check your microphone in the browser: a live level meter, a sound spectrum, the settings your browser uses, and a short record-and-play-back to hear how you sound. Nothing is recorded or sent.

Keep it one tap away for everyday use.

Bookmark Mic Test?

Press Ctrl + D now. Your browser opens its own bookmark box, where you choose the name and folder.

Or install fibub as an app: every tool you open then works offline.

  1. Allow mic
  2. Watch level
  3. Play back
Nothing is uploadedWorks offline once open

Press Start microphone. Your browser will ask for permission. Nothing is recorded or sent anywhere.

Level now
–
Peak (last 2 s)
–
Sample rate
–
Channels
–

Record and play back

Hear how you sound to others. The clip stays in this tab and is gone when you leave.

What the browser reports

StatusNot started

What it does

The Mic Test checks that your microphone works and is set to a sensible level, right in the browser. Press Start microphone, allow access, and speak: a bar shows the level as you talk, a spectrum shows which pitches it hears, and a plain sentence tells you whether you are too quiet, about right or so loud that the sound clips. You can then record a few seconds and play them back to hear exactly what other people hear on a call.

It works on laptops, desktops, phones and tablets, with built-in microphones, headsets, USB and Bluetooth mics. Nothing is recorded to a server or sent anywhere: the sound stays in your browser tab and the clip is gone when you leave. To check the other direction, use the speaker Test; for your camera, the webcam Test; to keep a recording, the voice recorder.

How to test your microphone

  1. Pick the microphone in the list (it shows names after you allow access once; until then it uses your default).
  2. Press Start microphone and allow it when the browser asks.
  3. Speak at your normal volume, about an arm’s length away. Watch the bar and the sentence under the buttons.
  4. Press Record, talk for the chosen length, and listen to the playback.
  5. Press Stop when you are done. The browser’s microphone light goes off.

What each part shows

  • Level now: how loud the sound is at this moment, in decibels below the loudest a recording can hold (0 dB). Speech usually sits between -40 and -15 dB.
  • Peak (last 2 s): the loudest point in the last two seconds; the thin line on the bar marks it. Peaks between -12 and -6 dB are ideal.
  • Spectrum: bars from low pitches (left) to high (right). A voice shows a hump between about 100 Hz and 4 kHz; a flat line means silence.
  • Call clean-up: switches on the browser’s echo cancellation, noise suppression and automatic volume, as a video call would. Leave it off to hear the raw microphone.
  • Listen live: sends the microphone to your speakers as you talk. Use headphones, or it will howl.
  • What the browser reports: sample rate, channels and which clean-up the browser applied.

Worked example

A laptop’s built-in mic, speaking at arm’s length, shows a level around -30 dB and peaks near -14 dB: “Good level for calls and recordings.” Leaning in and shouting pushes the peak to 0 dB and the bar turns red: “Clipping”. A headset mic switched to mute shows “silent” and the sentence says no sound is reaching the browser.

Why does my microphone not work?

  • “Not allowed”: the browser or the system blocked it. Click the lock or camera icon by the address bar and allow the microphone. On Windows, check Settings > Privacy > Microphone; on a Mac, System Settings > Privacy & Security > Microphone; on a phone, the browser app’s permissions.
  • “Another app is using it”: close video calls, recorders or other tabs using the mic.
  • No sound but no error: check the mute switch on the headset or keyboard, the input volume in your sound settings, and that the right microphone is picked in the list.
  • Bluetooth headset sounds muffled: many headsets drop to “headset” (call) quality while the mic is in use. That is normal for Bluetooth.

FAQs

Is my voice recorded or uploaded? No. The sound is read in your browser to draw the meter. The playback clip is held in this tab only and is deleted when you close it.

Why is the list of microphones empty or unnamed? Browsers hide device names until you allow access once, so sites cannot fingerprint you. Press Start and the names appear.

Why do the readings differ from my recording app? Apps may apply their own gain and clean-up. Switch off Call clean-up here to see the raw level.

Does it work on iPhone? Yes, in Safari and other browsers on iOS 14.3 and later.

Where the numbers come from

  • Levels are in dB below full scale (dBFS): 20 × log10 of the RMS or peak sample value; a full-scale sine is -3.01 dBFS RMS. Checked in tests/device.mjs.
  • Level bands (quiet below -36 dB peak, good -36 to -6 dB, clipping at 0 dB) are fibub's own rule of thumb for speech, rounded from common recording advice to peak between -12 and -6 dB.
  • Microphone settings (sample rate, channels, echo cancellation, noise suppression, auto gain, latency) are what the browser reports through MediaStreamTrack.getSettings(); some browsers leave some out.

Standard scientific values, such as constants, atomic weights and melting points, are facts found in every textbook; we name where ours were checked. If you are an author or publisher and want a value, a credit or a table changed or removed, tell us and we will act quickly.

Last updated 2026-11-19.

Change log for Mic Test

  1. Add 13 device testers (#T1051-#T1063) and allow the microphone on audio tools Details on GitHub

Every change to fibub

Related tools