Elasticity of solids
Class 11 · 200 questions and templates for Medical entrance (NEET), in order from warm-up to top rank. Check each answer, then read the full solution.
New to this topic? Read the lesson first: Elasticity of solids.
Loading questions… (they need JavaScript; nothing you type is sent anywhere)
Written questions with solutions
The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.
-
NATWarm-up
A force of 500 N pulls along the length of a rod whose cross-section is . Find the stress in the rod (in kPa).Answer and solution
Answer: 2500 kPa
Stress Pa kPa. -
MCQWarm-up
Longitudinal strain is defined as- force per unit area
- change in length divided by original length
- original length divided by change in length
- change in volume divided by pressure
Answer and solution
Answer: B
Strain : a ratio of two lengths. It has no unit and no dimensions. The other options describe stress, an inverted ratio and the inverse of the bulk modulus. -
MCQWarm-up
The SI unit of Young's modulus is- (pascal)
- no unit
Answer and solution
Answer: A
. Strain has no unit, so has the unit of stress, = Pa. -
MCQWarm-up
Hooke's law says that, within the elastic limit,- strain is inversely proportional to stress
- stress is proportional to the square of strain
- stress is independent of strain
- stress is directly proportional to strain
Answer and solution
Answer: D
The straight part of the stress-strain graph from the origin is Hooke's law. The slope is the modulus of elasticity. -
NATWarm-up
A wire 2 m long stretches by 2 mm under a load. Find the strain in units of .Answer and solution
Answer: 1
Strain . In units of the answer is 1. -
MCQWarm-up
Which of these has the largest Young's modulus?- rubber
- lead
- steel
- human bone
Answer and solution
Answer: C
Steel is about Pa, bone about Pa, lead about Pa and rubber only about to Pa. A material with larger is stiffer. -
MCQWarm-up
Which modulus of elasticity is meaningful for a liquid?- Young's modulus
- bulk modulus
- modulus of rigidity
- Poisson's ratio
Answer and solution
Answer: B
A liquid takes the shape of its container, so it has no shear modulus. It resists a change of volume, so it has a bulk modulus. A liquid in a container is not stretched along a line, so does not apply either. -
MCQWarm-up
The dimensional formula of Young's modulus isAnswer and solution
Answer: A
Same as stress or pressure: force over area . -
MCQWarm-up
A body is perfectly elastic if it- never changes its shape
- breaks when a force is applied
- keeps the new shape after the force is removed
- regains its original size and shape completely when the deforming force is removed
Answer and solution
Answer: D
That is the definition. Quartz and phosphor bronze are close to perfectly elastic. A body that keeps the new shape is called plastic (putty is an example). -
NATWarm-up
A wire carries a stress of and shows a strain of . Find its Young's modulus (in units of ).Answer and solution
Answer: 2
Pa, so the answer is 2. -
MCQWarm-up
The bulk modulus is the ratio of- tangential force to area
- longitudinal stress to longitudinal strain
- the pressure change to the fractional change in volume (with a minus sign)
- lateral strain to longitudinal strain
Answer and solution
Answer: C
. The minus sign makes positive, because volume falls when pressure rises. Options 2 and 3 are and Poisson's ratio; the first is a shear stress. -
MCQWarm-up
Twisting a metal rod about its length is mainly opposed by its- bulk modulus
- modulus of rigidity (shear modulus)
- Young's modulus
- compressibility
Answer and solution
Answer: B
Twisting slides each layer over the next one. This is a shear, so the shear (rigidity) modulus matters. -
MCQWarm-up
The compressibility of a material is- the reciprocal of its bulk modulus
- equal to its bulk modulus
- equal to its Young's modulus
- the reciprocal of its density
Answer and solution
Answer: A
. A highly compressible material has a small bulk modulus. Gases are far more compressible than liquids. -
NATWarm-up
A steel wire of cross-section has . What load (in N) produces a strain of ?Answer and solution
Answer: 200 N
N. Remember . -
MCQWarm-up
The elastic limit of a wire is the stress beyond which- the wire breaks at once
- stress becomes proportional to strain
- the wire becomes perfectly elastic
- the wire does not return to its original length when the load is removed
Answer and solution
Answer: D
Beyond the elastic limit some permanent set remains (plastic deformation). The wire does not have to break there; breaking happens at a much larger stress. -
MCQWarm-up
Steel is more elastic than rubber because, for the same stress,- steel shows a larger strain
- steel shows no strain at all
- steel shows a smaller strain
- rubber has a larger Young's modulus
Answer and solution
Answer: C
In physics, "more elastic" means a larger modulus (a bigger restoring stress for the same strain). Steel has Pa and so a much smaller strain than rubber. -
MCQWarm-up
Poisson's ratio of a material is- measured in
- a pure number
- measured in
- measured in metre
Answer and solution
Answer: B
It is lateral strain divided by longitudinal strain: a ratio of two strains, so it has no unit. For most materials it lies between 0 and 0.5. -
MCQWarm-up
The elastic energy stored per unit volume in a stretched wire is- stress strain
- stressstrain
Answer and solution
Answer: A
Work done (the area under the force-extension line). Dividing by volume gives . -
MCQWarm-up
A wire stretches by 1 mm under a load of 2 kg. Within the elastic limit, a load of 6 kg (same wire) will stretch it by- 2 mm
- 6 mm
- 9 mm
- 3 mm
Answer and solution
Answer: D
Extension is proportional to load: . Tripling the load triples the extension: mm. -
MCQWarm-up
Stress produced in a wire depends on- the load and the length only
- the length and the material only
- the load and the area of cross-section, but not on the length
- the material only
Answer and solution
Answer: C
Stress is . The length of the wire does not enter. (Extension does depend on the length, strain does not.) -
NATStandard
A steel wire of length 2 m and diameter 1 mm carries a 20 kg load. Find its extension (in mm, 2 decimals). , .Answer and solution
Answer: 2.5 mm (±0.02)
N. . mm.Why people get this wrong: Use the area from the diameter: radius is half of 1 mm.
-
MCQStandard
A wire of diameter 2 mm supports a load of 150 N. The stress in it is- 191 MPa
- 47.7 MPa
- 23.9 MPa
- 95.5 MPa
Answer and solution
Answer: B
. MPa. Using the diameter as the radius would give a quarter of this, and using gives a quarter too.Why people get this wrong: Radius, not diameter, in .
-
NATStandard
A wire is stretched by 2 mm by a load of 100 N applied slowly within the elastic limit. How much elastic energy (in J) is stored in it?Answer and solution
Answer: 0.1 J (±0.001)
J. Using would give 0.2 J, which is the work done by a load that drops freely and falls through 2 mm. Half of that is lost as heat and sound.Why people get this wrong: The factor (the force grows from zero).
-
MCQStandard
A wire of Pa is stretched to a strain of . The elastic energy stored per unit volume is- 1 × 105 J m-3
- 2 × 105 J m-3
- 1 × 108 J m-3
- 50000 J m-3
Answer and solution
Answer: A
. -
NATStandard
Two steel wires of lengths 1.5 m and 0.5 m, both of cross-section , are joined end to end and a 100 N load is hung from the free end. Find the total extension (in mm). Pa.Answer and solution
Answer: 1 mm (±0.005)
In series, both wires carry the same force (100 N). Total extension m mm. -
MCQStandard
A steel wire and a brass wire have the same length and area. They hang side by side and together carry a 300 N load, both stretching equally. If Pa and Pa, the steel wire carries- 100 N
- 150 N
- 250 N
- 200 N
Answer and solution
Answer: D
Equal extension means is the same, so . Shares: steel : brass = 2 : 1. Steel carries N.Why people get this wrong: The stiffer wire takes the larger share.
-
NATStandard
A steel rod is clamped rigidly at both ends at 20 °C and then heated to 70 °C. Find the thermal stress in it (in MPa). Pa, .Answer and solution
Answer: 120 MPa
The rod tries to expand by a strain but cannot. Stress Pa MPa. -
MCQStandard
The bulk modulus of water is Pa. When the pressure on it rises by Pa, its volume decreases by (in percent)- 0.00909 %
- 9.09 %
- 0.909 %
- 11 %
Answer and solution
Answer: C
. -
NATStandard
A uniform steel wire 100 m long hangs from a support. Find its extension due to its own weight alone (in mm, 2 decimals). , Pa, .Answer and solution
Answer: 1.91 mm (±0.02)
The stress at distance from the free end is , so mm.Why people get this wrong: The factor 2: the weight acts like a load of half of the wire at the end.
-
NATStandard
A rod with Poisson's ratio 0.3 is stretched to a longitudinal strain of . Find the lateral (sideways) contraction strain, in units of .Answer and solution
Answer: 6
Lateral strain longitudinal strain .