Home / Courses / IIT JAM Physics / Practice / Transistors and amplifiers

Transistors and amplifiers

Electronics · 82 questions and templates for IIT JAM Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

New to this topic? Read the lesson first: Transistors and amplifiers.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    An npn transistor is used as an amplifier in its active region. The base-emitter (BE) and base-collector (BC) junctions are then
    1. BE forward biased, BC forward biased
    2. BE forward biased, BC reverse biased
    3. BE reverse biased, BC reverse biased
    4. BE reverse biased, BC forward biased
    Answer and solution

    Answer: B

    In the active region the emitter must inject electrons into the base, so the BE junction is forward biased. The collector must sweep those electrons out of the base, so the BC junction is reverse biased (its field pulls electrons from base to collector). Both forward is saturation, both reverse is cut-off, and BE reverse with BC forward is the little-used inverse-active mode.

    Why people get this wrong: Both junctions forward biased is saturation: the transistor is a closed switch there, not an amplifier.

  2. NATWarm-up

    The common-base current gain of a transistor is α=0.98. Its common-emitter current gain β is ______.
    Answer and solution

    Answer: 49 (±0.01)

    From IE=IB+IC and IC=αIE: IB=(1−α)IE, so β=IC/IB=α/(1−α)=0.98/0.02=49.

    Why people get this wrong: Writing β=1/(1−α)=50 gives IE/IB, which is β+1, not β.

  3. MCQWarm-up

    For a bipolar transistor in any mode, Kirchhoff's current law gives the emitter current IE as
    1. IB−IC
    2. IC−IB
    3. IB+IC
    4. IC/IB
    Answer and solution

    Answer: C

    Treat the transistor as one node: the current entering through the base and collector (npn) leaves through the emitter, so IE=IB+IC. For pnp all three directions reverse and the same relation holds.

    Why people get this wrong: IC/IB is the current gain β, a ratio, not a current.

  4. MCQWarm-up

    Why is the base of a bipolar junction transistor made thin and lightly doped?
    1. To make the base resistance as small as possible
    2. So that the collector junction breaks down at a low voltage
    3. To let the transistor carry a larger emitter current
    4. So that almost all carriers injected by the emitter reach the collector instead of recombining in the base
    Answer and solution

    Answer: D

    Electrons injected from the emitter into a p-type base can recombine with holes there. A thin base gives them little time to do so, and light doping gives them few holes to meet. So nearly all of them diffuse across to the BC junction and are swept into the collector: α is close to 1 and β is large.

    Why people get this wrong: Light doping actually raises the base resistance; that is a cost, not the purpose.

  5. NATWarm-up

    A transistor with β=150 works in its active region with a base current of 20 μA. Its collector current is ______ mA.
    Answer and solution

    Answer: 3 mA (±0.01)

    IC=βIB=150×20 μA=3000 μA=3 mA.

    Why people get this wrong: Forgetting to convert microamps to milliamps gives 3000.

  6. MCQWarm-up

    In a single-stage common-emitter amplifier at mid-band frequencies, the output voltage and the input voltage differ in phase by
    1. 180∘
    2. 0∘
    3. 90∘
    4. 45∘
    Answer and solution

    Answer: A

    A rise in input raises IB and so IC. The larger drop ICRC across the collector resistor lowers VC=VCC−ICRC. Output falls as input rises: a phase shift of 180∘ (the gain is negative).

    Why people get this wrong: The emitter follower (common collector) and common base give 0∘; only common emitter inverts.

  7. MCQWarm-up

    In the circuit symbol of an npn bipolar transistor, the arrow on the emitter points
    1. into the transistor
    2. out of the collector
    3. out of the transistor
    4. into the base
    Answer and solution

    Answer: C

    The arrow shows the direction of conventional current through the base-emitter junction when it is forward biased: from p (base) to n (emitter), i.e. out of the npn transistor at the emitter. In a pnp transistor it points in ("Pointing iN Proudly" is one memory aid).

    Why people get this wrong: Following the electron flow: in an npn device electrons enter at the emitter, opposite to the arrow.

  8. MCQStandard

    Which configuration has a current gain slightly less than 1 but can give a large voltage gain?
    1. Common emitter
    2. Common base
    3. Common collector
    4. None: a current gain below 1 means no voltage gain either
    Answer and solution

    Answer: B

    In common base the input current is IE and the output current is IC=αIE, so the current gain is α<1. But the input resistance is tiny (re=VT/IE, tens of ohms) while the output is taken across a large RC, so the voltage gain ≈RC/re can be in the hundreds. Common collector is the other way round: voltage gain just under 1, large current gain.

    Why people get this wrong: A gain below 1 in current does not forbid voltage gain, because the input and output resistances differ hugely.

  9. NATStandard

    A fixed-bias common-emitter stage has VCC=12 V, base resistor RB=470 kΩ from VCC to the base, RC=2.2 kΩ, β=100 and VBE=0.7 V. The quiescent collector-emitter voltage is ______ V (to two decimal places).
    Answer and solution

    Answer: 6.71 V (±0.03)

    IB=(VCC−VBE)/RB=11.3/470000=24.04 μA. IC=βIB=2.404 mA. VCE=VCC−ICRC=12−2.404×2.2=12−5.29=6.71 V. This is positive and well above about 0.2 V, so the transistor is indeed active.

    Why people get this wrong: Dropping VBE gives IB=25.5 μA and VCE=6.38 V.

  10. MSQStandard

    An npn transistor is driven into saturation. Which statements are correct?
    1. Both junctions are forward biased.
    2. The relation IC=βIB still holds.
    3. VCE is small, typically about 0.1 to 0.3 V.
    4. The collector current is set mainly by VCC and the collector resistor.
    Answer and solution

    Answer: A, C, D

    In saturation the base is driven so hard that the collector voltage falls below the base voltage, so the BC junction also becomes forward biased. VCE is then only a few tenths of a volt and IC≈(VCC−VCE,sat)/RC, fixed by the outside circuit. Extra base current no longer raises IC, so IC<βIB: the relation IC=βIB holds only in the active region.

    Why people get this wrong: Using IC=βIB without checking VCE gives a negative VCE, the sign that the transistor is saturated.

  11. MCQStandard

    A common-emitter stage has VCC=10 V and RC=2 kΩ (no emitter resistor). If the Q-point sits at VCE=4 V, the quiescent collector current is
    1. 2 mA
    2. 5 mA
    3. 7 mA
    4. 3 mA
    Answer and solution

    Answer: D

    The DC load line is VCE=VCC−ICRC. With VCE=4 V: IC=(10−4)/2000=3 mA. The line runs from IC=5 mA at VCE=0 to VCE=10 V at IC=0.

    Why people get this wrong: 5 mA is the end of the load line on the current axis (VCE=0), not the Q-point.

  12. MCQStandard

    A BJT is biased at IC=1 mA at room temperature, where the thermal voltage VT=kT/e=25 mV. Its transconductance gm is
    1. 25 mA/V
    2. 1 mA/V
    3. 40 mA/V
    4. 4 mA/V
    Answer and solution

    Answer: C

    In the active region IC=ISeVBE/VT, so gm=dIC/dVBE=IC/VT=1 mA/25 mV=0.04 A/V =40 mA/V.

    Why people get this wrong: 25 is VT in mV; gm is its inverse times IC.

  13. MCQStandard

    Which of the following is NOT true of an emitter follower (common-collector amplifier)?
    1. Its voltage gain is slightly less than 1.
    2. Its output is in phase with its input.
    3. Its output impedance is high.
    4. It is used as a buffer between a high-impedance source and a low-impedance load.
    Answer and solution

    Answer: C

    The emitter follows the base one VBE lower, so the gain is just under 1 and in phase. Looking back into the emitter you see re plus the source resistance divided by (β+1): a LOW output impedance. Looking into the base you see (β+1)RE: a high input impedance. That combination is what makes it a buffer. So the statement about high output impedance is the false one.

    Why people get this wrong: The high impedance is at the input (the base), not at the output.

  14. MCQStandard

    A transistor with β=99 carries an emitter current of 2 mA. Its base current is
    1. 19.8 μA
    2. 20.2 μA
    3. 2 μA
    4. 20 μA
    Answer and solution

    Answer: D

    IE=IB+IC=(β+1)IB, so IB=IE/(β+1)=2 mA/100=20 μA.

    Why people get this wrong: Dividing IE by β instead of β+1 gives 20.2 μA.

  15. MCQStandard

    In the active region of the common-emitter output characteristics, IC rises slowly as VCE increases at fixed IB. The main reason is
    1. the BC depletion layer widening into the base, which makes the effective base narrower
    2. avalanche multiplication in the emitter junction
    3. heating of the transistor by the collector current
    4. a rise in the base doping with voltage
    Answer and solution

    Answer: A

    A larger VCE reverse biases the BC junction more and its depletion layer eats further into the base. A narrower effective base means fewer carriers recombine there and the concentration gradient across it is steeper, so β and IC creep up. This base-width modulation is the Early effect; extending the sloping lines back meets the VCE axis near −VA, the Early voltage.

    Why people get this wrong: Avalanche breakdown happens at much higher VCE and makes IC shoot up, not creep.

  16. MSQStandard

    Compared with a BJT, which statements about a junction field-effect transistor (JFET) are correct?
    1. It is a voltage-controlled device.
    2. Its input (gate) impedance is very high.
    3. Its current is carried by both electrons and holes.
    4. Its gate-channel junction is forward biased in normal use.
    Answer and solution

    Answer: A, B

    The gate voltage widens or narrows the depletion layers that squeeze the channel, so the drain current is controlled by a voltage. The gate junction is kept reverse biased, so only a tiny leakage current flows into the gate: very high input impedance. Current flows through the channel by majority carriers only (electrons in an n-channel JFET), so the JFET is unipolar; the BJT is the bipolar one.

    Why people get this wrong: Forward biasing the gate would let gate current flow and destroy the high input impedance that is the point of a FET.

  17. NATStandard

    An n-channel JFET has IDSS=12 mA and pinch-off voltage VP=−4 V. With VGS=−2 V and the device in saturation, the drain current is ______ mA.
    Answer and solution

    Answer: 3 mA (±0.01)

    Shockley's equation: ID=IDSS(1−VGS/VP)2=12(1−0.5)2=12×0.25=3 mA.

    Why people get this wrong: Forgetting the square gives 6 mA: the transfer curve is a parabola, not a straight line.

  18. MCQStandard

    Two amplifier stages with voltage gains of 50 and 20 are connected in cascade (the second does not load the first). The overall gain in decibels is
    1. 70 dB
    2. 60 dB
    3. 34 dB
    4. 1000 dB
    Answer and solution

    Answer: B

    Gains multiply: 50×20=1000. In decibels, 20log10⁡1000=60 dB. Equivalently the stage gains are 20log10⁡50=34 dB and 20log10⁡20=26 dB, and decibels add: 34+26=60 dB.

    Why people get this wrong: Adding the plain gains (50+20=70) and calling it dB mixes the two scales.

  19. NATStandard

    A transistor in its active region carries IC=20 mA with VCE=4.5 V, and IB=0.20 mA with VBE=0.70 V. The power it dissipates is ______ mW (to the nearest whole number).
    Answer and solution

    Answer: 90 mW (±0.5)

    Power is voltage times current at each port: P=VCEIC+VBEIB=(4.5)(20)+(0.70)(0.20)=90+0.14=90.1 mW, almost all of it at the collector junction. That is the figure to compare with the device's power rating (and to use for heat-sink sizing).

    Why people get this wrong: Using VCCIC: the part of the supply dropped across the load resistor is dissipated there, not in the transistor.

  20. MCQStandard

    An n-channel enhancement MOSFET has threshold VT=1.0 V. With VGS=3.0 V and VDS=1.5 V it operates in
    1. the triode (linear) region
    2. saturation
    3. cut-off
    4. breakdown
    Answer and solution

    Answer: A

    The channel exists because VGS>VT. It is pinched off at the drain end only if VDS≥VGS−VT=2.0 V. Here VDS=1.5 V <2.0 V, so the channel is continuous and the device is in the triode region, acting like a voltage-controlled resistor.

    Why people get this wrong: Comparing VDS with VT instead of with the overdrive VGS−VT.

  21. NATExam level

    A voltage-divider biased common-emitter stage has VCC=15 V, R1=100 kΩ (top) and R2=20 kΩ (bottom), RE=1 kΩ, RC=4 kΩ and VBE=0.7 V. Treat β as very large (neglect the base current). The quiescent VCE is ______ V.
    Answer and solution

    Answer: 6 V (±0.03)

    With no base current the divider gives VB=15×20/120=2.5 V. Then VE=2.5−0.7=1.8 V and IE=1.8/1000=1.8 mA ≈IC. VCE=VCC−IC(RC+RE)=15−1.8×5=6 V.

    Why people get this wrong: Leaving out the drop across RE gives VCE=7.8 V.

  22. NATExam level

    A common-emitter amplifier with a fully bypassed emitter resistor is biased at IC=2 mA (VT=25 mV). RC=5 kΩ and the load RL=5 kΩ is capacitively coupled. Ignoring the Early effect, the magnitude of the mid-band voltage gain is ______.
    Answer and solution

    Answer: 200 (±1)

    gm=IC/VT=2/25=0.08 A/V. For the signal, RC and RL are in parallel: 2.5 kΩ. |Av|=gm(RC∥RL)=0.08×2500=200.

    Why people get this wrong: Using RC alone gives 400: the coupled load is in parallel with RC for AC.

  23. MCQExam level

    A common-emitter stage at IC=1 mA (VT=25 mV, β large) has RC=4 kΩ and an unbypassed emitter resistor RE=500 Ω, with no load. Taking the intrinsic emitter resistance into account, the voltage gain is closest to
    1. −7.6
    2. −160
    3. +7.6
    4. −8.0
    Answer and solution

    Answer: A

    The intrinsic emitter resistance is re=VT/IE≈25 Ω. The signal current in the emitter is vin/(re+RE) and almost all of it flows through RC, so Av=−RC/(re+RE)=−4000/525=−7.62.

    Why people get this wrong: −160 ignores RE (as if bypassed); −8.0 is the rough −RC/RE that leaves out re; the plus sign forgets the inversion.

  24. MSQExam level

    The bypass capacitor across RE in a common-emitter amplifier is removed. Which statements are correct?
    1. The magnitude of the voltage gain falls.
    2. The input resistance seen at the base rises.
    3. The gain becomes less sensitive to changes in β and temperature.
    4. The output is no longer inverted.
    Answer and solution

    Answer: A, B, C

    Without the bypass, RE carries the signal too, giving negative (series current) feedback. The gain drops from −RC/re to about −RC/(re+RE), which depends on resistors rather than on the transistor, so it is steadier. The input resistance at the base rises from (β+1)re to (β+1)(re+RE). The collector still swings opposite to the base, so the output stays inverted.

    Why people get this wrong: Feedback reduces the size of the gain, but its sign is set by where the output is taken (collector), which has not changed.

  25. NATExam level

    From a set of common-emitter output characteristics at VCE=5 V, a student reads IC=2.1 mA on the curve for IB=20 μA and IC=3.3 mA on the curve for IB=32 μA. The small-signal current gain βac is ______.
    Answer and solution

    Answer: 100 (±0.5)

    βac=ΔIC/ΔIB at constant VCE =(3.3−2.1) mA/(32−20) μA=1.2 mA/12 μA=100.

    Why people get this wrong: The DC ratio IC/IB at one point (e.g. 2.1/0.020=105) is βdc, which is not the same.

  26. MCQExam level

    For a transistor in the common-emitter configuration, the hybrid parameter hfe is
    1. ∂VBE/∂IB at constant VCE
    2. ∂IC/∂VCE at constant IB
    3. ∂IC/∂IB at constant VCE
    4. ∂VBE/∂VCE at constant IB
    Answer and solution

    Answer: C

    The h-parameters use IB and VCE as the independent variables. hfe ("forward", "emitter") is the forward current gain with the output short-circuited for signals: ∂IC/∂IB at constant VCE. The others are hie (input resistance), hoe (output conductance) and hre (reverse voltage ratio), in the order listed in the other options.

    Why people get this wrong: ∂IC/∂VCE is hoe, the slope of the output curves, which the Early effect makes non-zero.

  27. NATExam level

    A common-emitter stage has VCC=12 V, RC=3 kΩ, no emitter resistor and no external load, so the AC and DC load lines coincide. Treating saturation as VCE=0, the quiescent collector current that allows the largest undistorted symmetric output swing is ______ mA.
    Answer and solution

    Answer: 2 mA (±0.02)

    The load line runs from (VCE,IC)=(12 V,0) to (0,4 mA). For the largest symmetric swing the Q-point sits at its middle: VCE=6 V, IC=6/3000=2 mA. The output can then swing ±6 V before hitting cut-off or saturation.

    Why people get this wrong: When an external load is coupled in, the AC load line is steeper and the best Q-point moves; here there is no load.

  28. MSQExam level

    Which statements about MOSFETs are correct?
    1. An enhancement n-channel MOSFET conducts only when VGS exceeds a positive threshold voltage.
    2. A depletion n-channel MOSFET conducts at VGS=0.
    3. The gate draws essentially no DC current because it is insulated by an oxide layer.
    4. In the saturation region the drain current rises in proportion to VDS.
    Answer and solution

    Answer: A, B, C

    An enhancement device has no channel until VGS>VT pulls enough electrons under the gate. A depletion device is built with a channel, so it conducts at VGS=0 and a negative VGS turns it off. The gate is a capacitor plate on silicon dioxide, so no DC gate current flows. In saturation the channel is pinched off at the drain end and ID is nearly independent of VDS (it follows (VGS−VT)2); the linear rise with VDS belongs to the ohmic (triode) region.

    Why people get this wrong: MOSFET "saturation" means the current saturates; BJT "saturation" means the voltage VCE collapses. Same word, opposite regions.

  29. MCQExam level

    A transistor with β=200 is biased at IC=0.5 mA (VT=25 mV). Its small-signal input resistance rπ (looking into the base, emitter grounded) is
    1. 50 Ω
    2. 5 kΩ
    3. 40 kΩ
    4. 10 kΩ
    Answer and solution

    Answer: D

    gm=IC/VT=0.5/25=0.02 A/V. rπ=β/gm=200/0.02=10000 Ω=10 kΩ. Equivalently rπ=(β+1)re≈200×50 Ω.

    Why people get this wrong: 50 Ω is re=VT/IE, the resistance seen looking into the emitter, which is β times smaller.

  30. MCQExam level

    Arrange the three single-transistor configurations in order of increasing input impedance.
    1. CB < CE < CC
    2. CC < CE < CB
    3. CE < CB < CC
    4. CB < CC < CE
    Answer and solution

    Answer: A

    Common base: input at the emitter, about re (tens of ohms). Common emitter: input at the base, rπ=(β+1)re (kilohms). Common collector: input at the base with RE in the emitter, (β+1)(re+RE) (hundreds of kilohms). So CB < CE < CC.

    Why people get this wrong: The output impedances run nearly the other way: CC is the lowest.

← All topics · Timed mock test →