Home / Courses / IIT JAM Physics / Practice / The first law: work, heat and processes

The first law: work, heat and processes

Kinetic theory and thermodynamics · 78 questions and templates for IIT JAM Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

New to this topic? Read the lesson first: The first law: work, heat and processes.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    Let Q be the heat given to a gas and W the work done by the gas. The first law of thermodynamics reads
    1. ΔU=Q+W
    2. W=Q+ΔU
    3. Q=ΔU+W
    4. Q=ΔU−W
    Answer and solution

    Answer: C

    Energy is conserved: the heat put in either raises the internal energy or leaves as work done on the surroundings, Q=ΔU+W. (Chemists often use W for the work done on the system, and then write ΔU=Q+W; same physics, different sign of W.)

    Why people get this wrong: Option A is correct only in the other sign convention. Always check how the question defines W.

  2. NATWarm-up

    Two moles of an ideal gas are heated at constant pressure from 300 K to 350 K. The work done by the gas is ______ J (R=8.314 J mol−1 K−1).
    Answer and solution

    Answer: 831.4 J (±2)

    At constant pressure W=PΔV=nRΔT=2×8.314×50=831.4 J. The kind of gas does not matter for the work.
  3. MCQWarm-up

    In which process does a gas do no work on its surroundings?
    1. Isochoric (constant volume)
    2. Isobaric (constant pressure)
    3. Isothermal (constant temperature)
    4. Adiabatic (no heat exchange)
    Answer and solution

    Answer: A

    Work =∫PdV, which is zero when the volume does not change. All heat then goes into internal energy: Q=ΔU.
  4. MSQWarm-up

    Which of the following are state functions (depend only on the state, not on how it was reached)?
    1. Internal energy U
    2. Heat Q absorbed
    3. Enthalpy H
    4. Work W done
    Answer and solution

    Answer: A, C

    U and H=U+PV are properties of the state. Q and W describe a process: between the same two states they differ from path to path, only their difference Q−W=ΔU is fixed.

    Why people get this wrong: Heat and work are energy in transit, not something a system "contains".

  5. NATWarm-up

    The heat needed to raise the temperature of 1 mol of an ideal monatomic gas by 10 K at constant volume is ______ J.
    Answer and solution

    Answer: 124.7 J (±1)

    Q=nCVΔT=1×32×8.314×10≈124.7 J.
  6. MCQWarm-up

    An ideal gas in an insulated container expands suddenly into an evacuated region (free expansion). Then
    1. Q=0, W>0 and the gas cools
    2. Q>0, W=0 and the gas warms
    3. Q=0, W<0 and the gas warms
    4. Q=0, W=0, ΔU=0 and the temperature does not change
    Answer and solution

    Answer: D

    No heat crosses the insulation (Q=0) and nothing pushes back on the expanding gas (W=0). So ΔU=0, and for an ideal gas U depends only on T: the temperature is unchanged.

    Why people get this wrong: Expansion does not automatically mean cooling. Gas cools only if it does work (or, for real gases, against its own attractions).

  7. MCQWarm-up

    A gas absorbs 500 J of heat while 200 J of work is done on it by a piston. The change in its internal energy is
    1. +300 J
    2. +700 J
    3. −300 J
    4. −700 J
    Answer and solution

    Answer: B

    Energy enters the gas both ways: 500 J as heat and 200 J as work done on it. So ΔU=Q+Won=500+200=+700 J. In the form ΔU=Q−W with W the work done by the gas, W=−200 J and the result is the same.

    Why people get this wrong: +300 J comes from subtracting the work while reading it as work done by the gas.

  8. NATStandard

    One mole of an ideal gas expands reversibly and isothermally at 300 K from 10 L to 30 L. The work done by the gas is ______ kJ.
    Answer and solution

    Answer: 2.74 kJ (±0.02)

    W=∫PdV=nRT∫dV/V=nRTln⁡(V2/V1)=8.314×300×ln⁡3=2494×1.0986≈2740 J =2.74 kJ.

    Why people get this wrong: Using PΔV with a fixed pressure: in an isothermal process the pressure changes all the time.

  9. MCQStandard

    A monatomic ideal gas is compressed reversibly and adiabatically to one eighth of its volume. Its absolute temperature becomes
    1. 32 times the original
    2. 4 times the original
    3. 8 times the original
    4. 2 times the original
    Answer and solution

    Answer: B

    TVγ−1 is constant, with γ−1=2/3. So T2/T1=82/3=4.

    Why people get this wrong: 32=85/3 is the pressure ratio, from PVγ = constant.

  10. MCQStandard

    At a given point on a P–V diagram of an ideal gas, the slope of the adiabat divided by the slope of the isotherm is
    1. γ−1
    2. 1
    3. γ
    4. 1/γ
    Answer and solution

    Answer: C

    Isotherm: PV= const gives dP/dV=−P/V. Adiabat: PVγ= const gives dP/dV=−γP/V. The ratio is γ>1, so the adiabat is steeper.
  11. NATStandard

    For an ideal gas of molar mass 28 g/mol, the difference of specific heats cp−cv (per kilogram) is ______ J kg−1 K−1.
    Answer and solution

    Answer: 296.9 J kg$^{-1}$ K$^{-1}$ (±2)

    Per mole, CP−CV=R (Mayer's relation). Per kilogram divide by the molar mass: 8.314/0.028≈296.9 J kg−1 K−1.

    Why people get this wrong: Answering 8.314: the question asks per kilogram, not per mole.

  12. MSQStandard

    A gas is taken once round a closed cycle. Which statements are correct?
    1. ΔU=0 for the cycle
    2. The net heat absorbed equals the net work done
    3. No heat is exchanged over the cycle
    4. The net work done by the gas equals the area enclosed on the P–V diagram, positive if the cycle runs clockwise
    Answer and solution

    Answer: A, B, D

    U is a state function, so it returns to its starting value. Then Qnet=Wnet, which equals the enclosed area (positive when the expansion happens at the higher pressure, i.e. clockwise with P up and V to the right). C is false: an engine absorbs net heat each cycle.
  13. MCQStandard

    The adiabatic bulk modulus of air (γ=1.4) at a pressure of 1.0×105 Pa is
    1. 1.4×105 Pa
    2. 1.0×105 Pa
    3. 0.71×105 Pa
    4. 0.4×105 Pa
    Answer and solution

    Answer: A

    B=−VdP/dV. For an adiabat dP/dV=−γP/V, so BS=γP=1.4×105 Pa. The isothermal modulus is BT=P. (Newton used P for the speed of sound and got it 15% too low; Laplace corrected it with γP.)
  14. NATStandard

    Heat is supplied to a rigid diatomic ideal gas at constant pressure. The fraction of the heat that is converted into work done by the gas is ______ (to two decimal places).
    Answer and solution

    Answer: 0.29 (±0.01)

    W=nRΔT and Q=nCPΔT=72nRΔT. So W/Q=2/7≈0.29. The other 5/7 raises the internal energy.
  15. MCQStandard

    For an ideal gas the change in internal energy between temperatures T1 and T2 is ΔU=nCV(T2−T1). This holds
    1. only for constant-volume processes
    2. only for adiabatic processes
    3. only for reversible processes
    4. for any process between those temperatures
    Answer and solution

    Answer: D

    For an ideal gas U depends only on T. CV is just a convenient way to measure dU/dT (it was found at constant volume, where Q=ΔU), but the change in U is the same along any path between the two temperatures.

    Why people get this wrong: The "V" in CV tempts you to restrict the formula to isochoric processes.

  16. MCQStandard

    One mole of an ideal gas at 300 K expands along the path PV2= constant until its volume doubles. Its final temperature is
    1. 212 K
    2. 150 K
    3. 600 K
    4. 75 K
    Answer and solution

    Answer: B

    With P=RT/V: PV2=RTV is constant, so TV is constant. Doubling V halves T: 150 K.
  17. MCQStandard

    A gas is compressed adiabatically. With W the work done by the gas, which set is right?
    1. W<0, ΔU=0, temperature unchanged
    2. W=0, ΔU>0, temperature rises
    3. W<0, ΔU>0, temperature rises
    4. W>0, ΔU<0, temperature falls
    Answer and solution

    Answer: C

    In compression the surroundings push on the gas, so the gas does negative work. With Q=0, ΔU=−W>0, and the temperature rises (a bicycle pump gets warm).
  18. MCQStandard

    The molar heat capacity of an ideal gas is zero in one process and infinite in another. These are, respectively,
    1. isobaric and isochoric
    2. isothermal and adiabatic
    3. isochoric and isobaric
    4. adiabatic and isothermal
    Answer and solution

    Answer: D

    C=1ndQdT. In a reversible adiabatic process dQ=0 while T changes, so C=0. In an isothermal process heat flows while dT=0, so C is infinite (formally). Isochoric and isobaric give the finite CV and CP.

    Why people get this wrong: Swapping them: "isothermal" sounds like no heat, but it is the adiabatic process that has no heat.

  19. NATStandard

    A 1.0 kW heater runs for 2.0 s inside 0.50 mol of a rigid diatomic ideal gas held at constant pressure. Ignoring losses, the temperature of the gas rises by ______ K (R=8.314 J mol−1 K−1).
    Answer and solution

    Answer: 137 (±1.5)

    The heater supplies Q=1000×2.0=2000 J. At constant pressure Q=nCPΔT with CP=72R for a rigid diatomic gas, so ΔT=20000.50×3.5×8.314=137 K. Part of the heat (2/7 of it) goes into the work of expansion, which is why the rise is smaller than at constant volume.

    Why people get this wrong: Using CV=52R gives 192 K, which ignores the work done pushing the piston out.

  20. MCQStandard

    Water in a thermally insulated container is stirred by a paddle wheel driven by a falling weight, and its temperature rises. Taking the water as the system, which description is right?
    1. Heat flows into the water from the paddle, so Q>0 and W=0.
    2. No work is done, because the volume of the water does not change.
    3. The internal energy is unchanged, since the container is insulated.
    4. No heat enters (Q=0); work is done on the water, and its internal energy rises by that amount.
    Answer and solution

    Answer: D

    Heat is energy that crosses the boundary because of a temperature difference. Here the paddle and water start at the same temperature and the walls are insulating, so Q=0. The paddle does work on the water (shaft work, not PdV work), and by the first law ΔU=Won. The same final state could be reached by heating instead, which is the point of Joule's experiment: U is a state function, heat and work are not.

    Why people get this wrong: A temperature rise does not prove that heat flowed in; work can raise the temperature too.

  21. MSQStandard

    Which statements about the enthalpy H=U+PV are correct?
    1. In a process at constant pressure with only PdV work, the heat absorbed equals ΔH.
    2. For an ideal gas, H depends on temperature only.
    3. When an ideal gas expands freely into a vacuum inside an insulated box, ΔH=0.
    4. In a reversible isothermal expansion of an ideal gas, ΔH equals the heat absorbed.
    Answer and solution

    Answer: A, B, C

    At constant P, Q=ΔU+PΔV=Δ(U+PV)=ΔH. For an ideal gas U(T) and PV=nRT, so H=U+nRT depends on T alone. In a free expansion T is unchanged for an ideal gas, so ΔH=0. In a reversible isothermal expansion ΔH=0 too, but the gas absorbs Q=nRTln⁡(V2/V1)>0, so the last statement is false.

    Why people get this wrong: Q=ΔH needs constant pressure; an isothermal expansion is not at constant pressure.

  22. NATExam level

    1 g of water at 100∘C and 1.013×105 Pa turns into steam. The latent heat is 2256 J/g and the volume grows by 1.670×10−3 m3. The increase in internal energy is ______ J.
    Answer and solution

    Answer: 2086.8 J (±3)

    The steam pushes back the atmosphere: W=PΔV=1.013×105×1.670×10−3=169.2 J. ΔU=Q−W=2256−169.2≈2086.8 J.

    Why people get this wrong: Taking ΔU=2256 J forgets that about 7.5% of the latent heat is spent pushing the air away.

  23. NATExam level

    Two moles of a rigid diatomic ideal gas expand adiabatically and cool from 400 K to 300 K. The work done by the gas is ______ J.
    Answer and solution

    Answer: 4157 J (±20)

    Q=0, so W=−ΔU=nCV(T1−T2)=2×52×8.314×100=4157 J. This holds even for an irreversible adiabatic expansion, since only the end temperatures enter.
  24. NATExam level

    A rigid diatomic ideal gas follows the polytropic process PV1.2= constant. Its molar heat capacity for this process, in units of R, is ______.
    Answer and solution

    Answer: -2.5 (±0.01)

    For PVn= const, W=RΔT/(1−n) per mole, so C=CV+R1−n=CV−Rn−1. With CV=52R and n=1.2: C=2.5R−5R=−2.5R. Negative: the gas does more work than the heat it takes in, so it cools while absorbing heat.

    Why people get this wrong: Dropping the minus sign. A negative heat capacity is not an error here; it happens for every 1<n<γ.

  25. MCQExam level

    For an ideal gas following PVn= constant, the molar heat capacity of the process is negative when
    1. 1<n<γ
    2. n>γ
    3. 0<n<1
    4. n<0
    Answer and solution

    Answer: A

    C=R(1γ−1−1n−1)=R(n−γ)(γ−1)(n−1). The numerator is negative for n<γ and the denominator positive for n>1. So C<0 for 1<n<γ, between the isotherm and the adiabat.
  26. NATExam level

    A gas is taken round a rectangle on a P–V diagram with corners at P=1×105 and 3×105 Pa, V=1 L and 4 L. The cycle runs anticlockwise (P up, V to the right). The net work done by the gas per cycle is ______ J.
    Answer and solution

    Answer: -600 J

    Area =ΔPΔV=(2×105)(3×10−3)=600 J. Anticlockwise means the gas expands along the low-pressure side and is compressed along the high-pressure side, so the net work by the gas is −600 J (it works as a refrigerator, not an engine).

    Why people get this wrong: Giving +600: the direction of the cycle sets the sign.

  27. MSQExam level

    An ideal gas goes from state A to state B along two different paths. Which quantities must be the same for both paths?
    1. ΔU
    2. Q
    3. W
    4. Q−W
    Answer and solution

    Answer: A, D

    ΔU is a change of a state function, and Q−W=ΔU. Heat and work separately depend on the path (the areas under the two curves differ).
  28. MCQExam level

    An ideal gas doubles its volume from the same initial state by (i) an isobaric, (ii) an isothermal and (iii) an adiabatic reversible process. The work done by the gas satisfies
    1. Wadiabatic>Wisothermal>Wisobaric
    2. Wisothermal>Wisobaric>Wadiabatic
    3. All three are equal
    4. Wisobaric>Wisothermal>Wadiabatic
    Answer and solution

    Answer: D

    Work is the area under the curve. From the same point, the isobar stays level, the isotherm falls as 1/V and the adiabat falls fastest, as V−γ. So the areas are in the order isobaric > isothermal > adiabatic.
  29. NATExam level

    Air (γ=1.4) at 300 K is compressed reversibly and adiabatically to one tenth of its volume, as in a diesel engine. The final temperature is ______ K.
    Answer and solution

    Answer: 753.6 K (±4)

    T2=T1(V1/V2)γ−1=300×100.4=300×2.512≈754 K, hot enough to ignite diesel fuel without a spark.
  30. MCQExam level

    Two identical samples of an ideal gas at pressure P0 are compressed to half their volume, one isothermally and one adiabatically (both reversible). The ratio Padiabatic/Pisothermal of the final pressures is
    1. 21−γ
    2. 2γ−1
    3. 2γ
    4. γ
    Answer and solution

    Answer: B

    Isothermal: P=2P0. Adiabatic: P=2γP0. Ratio 2γ−1>1: the adiabatic sample is hotter, so its pressure is higher.

← All topics · Timed mock test →