Home / Courses / IIT JAM Physics / Practice / Amplifiers and feedback

Amplifiers and feedback

Electronics · 13 questions and templates for IIT JAM Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    An amplifier of gain A has a fraction β of its output fed back to subtract from the input. The closed-loop gain is
    1. A/(1−Aβ)
    2. A/(1+Aβ)
    3. A(1+Aβ)
    4. 1/(Aβ) exactly
    Answer and solution

    Answer: B

    The amplifier sees xi=xs−βxo and gives xo=Axi. So xo=A(xs−βxo) and xo/xs=A/(1+Aβ). When the loop gain Aβ≫1 this tends to 1/β, set by the feedback network alone.

    Why people get this wrong: A/(1−Aβ) is positive feedback; 1/β is only the limit for large loop gain.

  2. MCQWarm-up

    A voltage gain of 100 expressed in decibels is
    1. 20 dB
    2. 10 dB
    3. 40 dB
    4. 100 dB
    Answer and solution

    Answer: C

    For voltage (or current) ratios, gain in dB =20log10⁡(100)=40 dB. A power ratio of 100 would be 10log10⁡100=20 dB.

    Why people get this wrong: Using 10log⁡ (the power formula) for a voltage ratio.

  3. MCQWarm-up

    Well above the corner frequency of a single-pole low-pass amplifier, the magnitude of its gain falls at
    1. 20 dB per decade (6 dB per octave)
    2. 40 dB per decade
    3. 3 dB per decade
    4. 10 dB per octave
    Answer and solution

    Answer: A

    |A|=A0/1+(f/fH)2≈A0fH/f for f≫fH: ten times the frequency, one tenth of the gain, which is −20 dB. Doubling the frequency halves it: −6 dB per octave. Each extra pole adds another −20 dB/decade.

    Why people get this wrong: The 3 dB figure is the drop at the corner itself, not the slope.

  4. NATWarm-up

    An amplifier with open-loop gain 1000 has negative feedback with β=0.009. Its closed-loop gain is ______.
    Answer and solution

    Answer: 100

    Loop gain Aβ=9, so Af=1000/(1+9)=100.

    Why people get this wrong: Using 1/β=111 ignores that the loop gain here is not large.

  5. MCQWarm-up

    Which of these is reduced, rather than improved, when negative feedback is applied to an amplifier?
    1. Bandwidth
    2. Harmonic distortion
    3. Sensitivity of the gain to transistor changes
    4. The magnitude of the gain
    Answer and solution

    Answer: D

    Negative feedback trades gain for everything else: the gain falls by the factor 1+Aβ, while bandwidth grows by about that factor, and distortion and sensitivity to A fall by it.

    Why people get this wrong: Reading "bandwidth" as something feedback reduces: for a single-pole amplifier it rises.

  6. MCQWarm-up

    Three voltage amplifier stages with gains of 20 dB, 15 dB and −5 dB (an attenuating filter) are cascaded without loading. The overall voltage gain is a factor of about
    1. 31.6
    2. 30
    3. 1000
    4. 1500
    Answer and solution

    Answer: A

    Decibel gains add: 20+15−5=30 dB. As a voltage ratio, 1030/20=101.5=31.6.

    Why people get this wrong: 30 is the dB number itself; 1000 is what 30 dB means for a power ratio, not a voltage ratio.

  7. MCQStandard

    A 10μF coupling capacitor feeds an amplifier whose input resistance is 2 kΩ (ideal voltage source driving it). The lower 3 dB frequency it sets is about
    1. 50 Hz
    2. 8.0 Hz
    3. 0.8 Hz
    4. 80 Hz
    Answer and solution

    Answer: B

    The capacitor and the input resistance form a high-pass RC: fL=1/(2πRC)=1/(2π×2000×10−5)=7.96 Hz.

    Why people get this wrong: Forgetting the 2π gives 50 Hz.

  8. MCQStandard

    The highest possible collector efficiency of an ideal class B push-pull amplifier with sinusoidal output is
    1. 25%
    2. 50%
    3. 78.5%
    4. 100%
    Answer and solution

    Answer: C

    At full swing Vp=VCC: Pout=VCC2/2RL and the supply delivers Pdc=2VCC2/(πRL). The ratio is π/4=78.5%. Class A reaches 25% with a resistive load and 50% with a transformer.

    Why people get this wrong: 50% is class A with transformer coupling.

  9. MCQStandard

    An amplifier of gain A=10 has a fraction β=0.05 of its output added in phase to its input (positive feedback). The closed-loop gain is
    1. 6.67
    2. 10
    3. 20
    4. infinite (it oscillates)
    Answer and solution

    Answer: C

    With positive feedback Af=A/(1−Aβ)=10/(1−0.5)=20. The loop gain Aβ=0.5 is below 1, so the circuit is stable, but the gain now depends strongly on A: a 10% rise in A would raise Af to 11/0.45=24.4.

    Why people get this wrong: 6.67 is the negative-feedback answer A/(1+Aβ); oscillation needs Aβ=1.

  10. MSQExam level

    Which statements about power amplifier classes are correct?
    1. In class A the transistor conducts over the whole cycle (360°)
    2. In class B each transistor conducts for half the cycle (180°)
    3. Class C conducts for less than 180° and is used with tuned loads at radio frequency
    4. Class AB conducts for more than 360°
    Answer and solution

    Answer: A, B, C

    Conduction angles: A 360°, AB between 180° and 360°, B 180°, C below 180°. A class C collector current is a train of pulses; a tuned circuit picks out the fundamental, giving efficiencies above 78.5%. No class conducts for more than a full cycle.

    Why people get this wrong: AB sits between A and B; it cannot exceed the full cycle.

  11. MCQExam level

    Crossover distortion in a class B complementary push-pull output stage is caused by
    1. the dead band near zero input, where neither transistor is conducting until |vBE| reaches about 0.6 V
    2. saturation of both transistors at the peaks
    3. unequal current gains of the npn and pnp transistors
    4. the output coupling capacitor
    Answer and solution

    Answer: A

    Each transistor needs about 0.6-0.7 V of base-emitter drive before it conducts, so the output sticks at zero while the input crosses through that band. Biasing both transistors slightly on (two diodes or a VBE multiplier between the bases) gives class AB and removes the dead band; overall negative feedback reduces what is left.

    Why people get this wrong: Clipping at the peaks is a different distortion.

  12. NATExam level

    A series-fed class A stage has its collector resistor RC=20 Ω to VCC=20 V and is biased at VCE=10 V, IC=0.50 A. The load is RC itself. With a sine-wave collector swing of 5.0 V peak, its efficiency (signal power in RC over DC power from the supply) is ______ % (to two decimal places).
    Answer and solution

    Answer: 6.25 (±0.05)

    The supply current averages to the quiescent 0.50 A whatever the signal, so PDC=20×0.50=10 W. Signal power in RC: Vp2/2RC=25/40=0.625 W. Efficiency =0.625/10=6.25%. Even at the full 10 V swing it reaches only 100/40/10=25%.

    Why people get this wrong: Taking the DC power as only IC2RC (the resistor's share) ignores the power wasted in the transistor.

← All topics · Timed mock test →