Home / Courses / GATE Physics / Practice / Transistors and amplifiers

Transistors and amplifiers

Electronics · 41 questions and templates for GATE Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    In the circuit symbol of an npn bipolar transistor, the arrow on the emitter points
    1. into the transistor
    2. out of the collector
    3. out of the transistor
    4. into the base
    Answer and solution

    Answer: C

    The arrow shows the direction of conventional current through the base-emitter junction when it is forward biased: from p (base) to n (emitter), i.e. out of the npn transistor at the emitter. In a pnp transistor it points in ("Pointing iN Proudly" is one memory aid).

    Why people get this wrong: Following the electron flow: in an npn device electrons enter at the emitter, opposite to the arrow.

  2. MCQStandard

    A BJT is biased at IC=1 mA at room temperature, where the thermal voltage VT=kT/e=25 mV. Its transconductance gm is
    1. 25 mA/V
    2. 1 mA/V
    3. 40 mA/V
    4. 4 mA/V
    Answer and solution

    Answer: C

    In the active region IC=ISeVBE/VT, so gm=dIC/dVBE=IC/VT=1 mA/25 mV=0.04 A/V =40 mA/V.

    Why people get this wrong: 25 is VT in mV; gm is its inverse times IC.

  3. MCQStandard

    In the active region of the common-emitter output characteristics, IC rises slowly as VCE increases at fixed IB. The main reason is
    1. the BC depletion layer widening into the base, which makes the effective base narrower
    2. avalanche multiplication in the emitter junction
    3. heating of the transistor by the collector current
    4. a rise in the base doping with voltage
    Answer and solution

    Answer: A

    A larger VCE reverse biases the BC junction more and its depletion layer eats further into the base. A narrower effective base means fewer carriers recombine there and the concentration gradient across it is steeper, so β and IC creep up. This base-width modulation is the Early effect; extending the sloping lines back meets the VCE axis near −VA, the Early voltage.

    Why people get this wrong: Avalanche breakdown happens at much higher VCE and makes IC shoot up, not creep.

  4. NATStandard

    A transistor in its active region carries IC=20 mA with VCE=4.5 V, and IB=0.20 mA with VBE=0.70 V. The power it dissipates is ______ mW (to the nearest whole number).
    Answer and solution

    Answer: 90 mW (±0.5)

    Power is voltage times current at each port: P=VCEIC+VBEIB=(4.5)(20)+(0.70)(0.20)=90+0.14=90.1 mW, almost all of it at the collector junction. That is the figure to compare with the device's power rating (and to use for heat-sink sizing).

    Why people get this wrong: Using VCCIC: the part of the supply dropped across the load resistor is dissipated there, not in the transistor.

  5. MCQStandard

    An n-channel enhancement MOSFET has threshold VT=1.0 V. With VGS=3.0 V and VDS=1.5 V it operates in
    1. the triode (linear) region
    2. saturation
    3. cut-off
    4. breakdown
    Answer and solution

    Answer: A

    The channel exists because VGS>VT. It is pinched off at the drain end only if VDS≥VGS−VT=2.0 V. Here VDS=1.5 V <2.0 V, so the channel is continuous and the device is in the triode region, acting like a voltage-controlled resistor.

    Why people get this wrong: Comparing VDS with VT instead of with the overdrive VGS−VT.

  6. NATExam level

    A common-emitter amplifier with a fully bypassed emitter resistor is biased at IC=2 mA (VT=25 mV). RC=5 kΩ and the load RL=5 kΩ is capacitively coupled. Ignoring the Early effect, the magnitude of the mid-band voltage gain is ______.
    Answer and solution

    Answer: 200 (±1)

    gm=IC/VT=2/25=0.08 A/V. For the signal, RC and RL are in parallel: 2.5 kΩ. |Av|=gm(RC∥RL)=0.08×2500=200.

    Why people get this wrong: Using RC alone gives 400: the coupled load is in parallel with RC for AC.

  7. MCQExam level

    A common-emitter stage at IC=1 mA (VT=25 mV, β large) has RC=4 kΩ and an unbypassed emitter resistor RE=500 Ω, with no load. Taking the intrinsic emitter resistance into account, the voltage gain is closest to
    1. −7.6
    2. −160
    3. +7.6
    4. −8.0
    Answer and solution

    Answer: A

    The intrinsic emitter resistance is re=VT/IE≈25 Ω. The signal current in the emitter is vin/(re+RE) and almost all of it flows through RC, so Av=−RC/(re+RE)=−4000/525=−7.62.

    Why people get this wrong: −160 ignores RE (as if bypassed); −8.0 is the rough −RC/RE that leaves out re; the plus sign forgets the inversion.

  8. MSQExam level

    The bypass capacitor across RE in a common-emitter amplifier is removed. Which statements are correct?
    1. The magnitude of the voltage gain falls.
    2. The input resistance seen at the base rises.
    3. The gain becomes less sensitive to changes in β and temperature.
    4. The output is no longer inverted.
    Answer and solution

    Answer: A, B, C

    Without the bypass, RE carries the signal too, giving negative (series current) feedback. The gain drops from −RC/re to about −RC/(re+RE), which depends on resistors rather than on the transistor, so it is steadier. The input resistance at the base rises from (β+1)re to (β+1)(re+RE). The collector still swings opposite to the base, so the output stays inverted.

    Why people get this wrong: Feedback reduces the size of the gain, but its sign is set by where the output is taken (collector), which has not changed.

  9. MCQExam level

    For a transistor in the common-emitter configuration, the hybrid parameter hfe is
    1. ∂VBE/∂IB at constant VCE
    2. ∂IC/∂VCE at constant IB
    3. ∂IC/∂IB at constant VCE
    4. ∂VBE/∂VCE at constant IB
    Answer and solution

    Answer: C

    The h-parameters use IB and VCE as the independent variables. hfe ("forward", "emitter") is the forward current gain with the output short-circuited for signals: ∂IC/∂IB at constant VCE. The others are hie (input resistance), hoe (output conductance) and hre (reverse voltage ratio), in the order listed in the other options.

    Why people get this wrong: ∂IC/∂VCE is hoe, the slope of the output curves, which the Early effect makes non-zero.

  10. MSQExam level

    Which statements about MOSFETs are correct?
    1. An enhancement n-channel MOSFET conducts only when VGS exceeds a positive threshold voltage.
    2. A depletion n-channel MOSFET conducts at VGS=0.
    3. The gate draws essentially no DC current because it is insulated by an oxide layer.
    4. In the saturation region the drain current rises in proportion to VDS.
    Answer and solution

    Answer: A, B, C

    An enhancement device has no channel until VGS>VT pulls enough electrons under the gate. A depletion device is built with a channel, so it conducts at VGS=0 and a negative VGS turns it off. The gate is a capacitor plate on silicon dioxide, so no DC gate current flows. In saturation the channel is pinched off at the drain end and ID is nearly independent of VDS (it follows (VGS−VT)2); the linear rise with VDS belongs to the ohmic (triode) region.

    Why people get this wrong: MOSFET "saturation" means the current saturates; BJT "saturation" means the voltage VCE collapses. Same word, opposite regions.

  11. MCQExam level

    A transistor with β=200 is biased at IC=0.5 mA (VT=25 mV). Its small-signal input resistance rπ (looking into the base, emitter grounded) is
    1. 50 Ω
    2. 5 kΩ
    3. 40 kΩ
    4. 10 kΩ
    Answer and solution

    Answer: D

    gm=IC/VT=0.5/25=0.02 A/V. rπ=β/gm=200/0.02=10000 Ω=10 kΩ. Equivalently rπ=(β+1)re≈200×50 Ω.

    Why people get this wrong: 50 Ω is re=VT/IE, the resistance seen looking into the emitter, which is β times smaller.

  12. MCQExam level

    An n-channel JFET has IDSS=8 mA and VP=−4 V. At VGS=−1 V its transconductance gm is
    1. 4 mS
    2. 3 mS
    3. 2.25 mS
    4. 6 mS
    Answer and solution

    Answer: B

    Differentiate ID=IDSS(1−VGS/VP)2: gm=2IDSS|VP|(1−VGSVP). Here gm0=2×8/4=4 mS and (1−0.25)=0.75, so gm=3 mS.

    Why people get this wrong: 4 mS is gm0, the value at VGS=0; 2.25 mS uses the squared factor 0.752.

  13. NATExam level

    A common-emitter stage uses collector-feedback bias: RC=2.0 kΩ from VCC=12 V to the collector, and RB=200 kΩ from the collector to the base (emitter grounded). With β=100 and VBE=0.70 V, the collector current is ______ mA (to two decimal places).
    Answer and solution

    Answer: 2.81 mA (±0.03)

    RC carries both IC and IB, i.e. (β+1)IB. Round the loop VCC→RC→RB→ base-emitter: 12=(β+1)IBRC+IBRB+0.70. So IB=11.3(101)(2.0 k)+200 k=11.3402 k=28.1 μA and IC=100IB=2.81 mA. Then VCE=12−101×28.1 μA×2.0 k =6.3 V: active, and if β rises, VC falls and pulls IB down, which stabilises the bias.

    Why people get this wrong: Treating RB as going to VCC (fixed bias) gives 5.65 mA; the feedback comes from the collector voltage.

  14. MSQExam level

    Which statements about temperature effects in a silicon BJT amplifier are correct?
    1. At fixed VBE, the collector current rises as the transistor warms up.
    2. An emitter resistor provides negative feedback that reduces the drift of IC with temperature.
    3. At fixed collector current, VBE falls by roughly 2 mV per kelvin.
    4. Thermal runaway is more likely when the bias circuit has a large emitter resistor.
    Answer and solution

    Answer: A, B, C

    IC≈ISeVBE/VT and IS grows steeply with temperature, so at fixed VBE the current climbs; equivalently, at fixed current VBE falls by about 2 mV/K. If more current heats the junction further, the loop can run away. An emitter resistor turns a rise in IC into a rise in VE, which lowers VBE and opposes the change: a large RE makes runaway less likely, not more.

    Why people get this wrong: Mixing up the two descriptions ("VBE falls" and "IC rises") as if they contradicted each other; they are the same physics at different constraints.

  15. MCQExam level

    A cascode stage (a common-emitter transistor feeding a common-base transistor) is used instead of a single common-emitter stage mainly because it
    1. has a much lower output resistance
    2. keeps the voltage gain of the first transistor near −1, so its base-collector capacitance is hardly Miller-multiplied and the bandwidth is wider
    3. doubles the voltage gain by placing two transistors in parallel
    4. needs no biasing at all
    Answer and solution

    Answer: B

    In a plain CE stage Cμ appears at the input multiplied by (1+|Av|) (Miller effect), which kills the high-frequency response. In the cascode the first transistor's collector sees the low input resistance ≈re of the common-base transistor, so its own gain is about −1 and Cμ is only doubled. The full voltage gain appears at the second collector. A bonus is a very high output resistance.

    Why people get this wrong: Thinking the extra transistor adds gain: the gain is about the same as one CE stage; it is the bandwidth that improves.

  16. NATHard

    A voltage-divider bias circuit has VCC=12 V, R1=56 kΩ (top), R2=12 kΩ (bottom), RE=1 kΩ, β=100 and VBE=0.7 V. Without neglecting the base current, the collector current is ______ mA (to two decimal places).
    Answer and solution

    Answer: 1.28 mA (±0.01)

    Replace the divider by its Thevenin equivalent: Vth=12×12/68=2.118 V and Rth=56∥12=9.882 kΩ. Round the base-emitter loop: Vth=IBRth+VBE+(β+1)IBRE, so IB=(2.118−0.7)/(9.882+101×1) kΩ=1.418/110.9 kΩ=12.79 μA. IC=βIB=1.28 mA.

    Why people get this wrong: Neglecting IB gives IC≈(2.118−0.7)/1 kΩ=1.42 mA, about 10% too high, because Rth is not small compared with βRE.

  17. MCQHard

    The stability factor S=∂IC/∂ICBO measures how much the collector current drifts with leakage. Which bias arrangement gives S closest to its ideal value of 1?
    1. Fixed bias with a large RB
    2. Fixed bias with a small RB
    3. Collector-to-base feedback bias with a large RC
    4. Voltage-divider bias with Rth/RE much less than 1
    Answer and solution

    Answer: D

    Fixed bias has S=1+β whatever RB is (often above 100). Collector feedback does better, but not close to 1. Voltage-divider bias has S=(1+β)1+Rth/RE1+β+Rth/RE, which tends to 1 as Rth/RE→0: the emitter voltage is then pinned by the stiff divider.

    Why people get this wrong: Changing RB in fixed bias changes the Q-point, not the stability factor.

  18. NATHard

    A voltage-divider biased stage has β=99, Thevenin base resistance Rth=10 kΩ and RE=2 kΩ. Its stability factor S=∂IC/∂ICBO is ______ (to two decimal places).
    Answer and solution

    Answer: 5.71 (±0.02)

    S=(1+β)1+Rth/RE1+β+Rth/RE=100×1+5100+5=600/105=5.71. Compare fixed bias, S=100.

    Why people get this wrong: Inverting the resistor ratio (RE/Rth=0.2) gives 100×1.2/100.2=1.20, far too optimistic. Fixed-bias intuition (S=1+β=100) ignores the emitter feedback.

  19. MCQHard

    An emitter follower (β=100, IE=1 mA, VT=25 mV, RE very large) is driven from a source of internal resistance 10 kΩ. Its output resistance is about
    1. 10 kΩ
    2. 25 Ω
    3. 124 Ω
    4. 1 MΩ
    Answer and solution

    Answer: C

    Looking back into the emitter you see re in series with the base-side resistance divided by (β+1), because a base current change is (β+1) times smaller than the emitter current change. Rout≈re+Rs/(β+1)=25+10000/101=25+99=124 Ω.

    Why people get this wrong: 25 Ω forgets the source resistance, which matters when it is large.

  20. MSQHard

    For an RC-coupled common-emitter amplifier, which statements about the frequency response are correct?
    1. The coupling and bypass capacitors set the lower cut-off frequency.
    2. The transistor's junction capacitances set the upper cut-off frequency.
    3. The base-collector capacitance appears at the input multiplied by about (1+|Av|).
    4. The mid-band gain depends strongly on the values of the coupling capacitors.
    Answer and solution

    Answer: A, B, C

    At low frequencies the large coupling and bypass capacitors have high reactance and cut the gain. At high frequencies the small junction capacitances short the signal. The base-collector capacitance Cμ sits between input and an inverted, amplified output, so the input sees Cμ(1+|Av|): the Miller effect, usually the main limit on bandwidth. In mid-band the coupling capacitors are effectively short circuits, so their values do not set the gain.

    Why people get this wrong: Mid-band is defined as the range where neither set of capacitors matters.

  21. MCQHard

    A transistor has base-collector capacitance Cμ=2 pF and the stage has a voltage gain of −99 from base to collector. The Miller capacitance it adds at the input is
    1. 2 pF
    2. 198 pF
    3. 0.02 pF
    4. 200 pF
    Answer and solution

    Answer: D

    When the base rises by v the collector falls by 99v, so the voltage across Cμ changes by 100v and it draws 100 times the charge a grounded capacitor would. CM=Cμ(1−Av)=2×(1+99)=200 pF.

    Why people get this wrong: 198 pF uses |Av| instead of 1+|Av|.

  22. MSQHard

    A BJT differential pair (long-tailed pair) has collector resistors RC and a tail that sets the total emitter current. Which statements are correct?
    1. With an ideal current source in the tail, the common-mode gain is zero.
    2. The differential gain taken single-ended from one collector is gmRC/2, where gm is that of one transistor.
    3. Replacing a tail resistor by a better current source raises the common-mode rejection ratio.
    4. Being direct-coupled, a differential pair cannot amplify DC signals.
    Answer and solution

    Answer: A, B, C

    A: a common-mode input cannot change the fixed tail current, so the collector currents do not change. B: a differential input vd puts ±vd/2 on the two bases, changing each collector current by gmvd/2. C: the common-mode gain is about RC/2REE, so a higher tail resistance (a current source) lowers it. D is false: with no coupling capacitors, it amplifies down to DC, which is why op-amps start with one.

    Why people get this wrong: Confusing "direct-coupled" with "AC only"; it is coupling capacitors that block DC.

  23. MSQHard

    Which statements comparing MOSFET and BJT small-signal behaviour are correct?
    1. At the same bias current, a MOSFET usually has a larger transconductance than a BJT.
    2. For a MOSFET in saturation, gm=2ID/(VGS−VT).
    3. A BJT's gm is proportional to its collector current, a MOSFET's to the square root of its drain current.
    4. The gate of a MOSFET draws essentially no DC current.
    Answer and solution

    Answer: B, C, D

    B: ID=k2Vov2 and gm=kVov=2ID/Vov. C: gm=IC/VT for the BJT, 2kID for the MOSFET. D: the gate is insulated by oxide. A is false: comparing I/VT with 2I/Vov, the BJT wins whenever Vov>2VT≈50 mV, which is the usual case.

    Why people get this wrong: Thinking the MOSFET's huge input resistance also means a larger transconductance.

  24. NATHard

    A basic two-transistor current mirror has a reference current of 1.00 mA and matched transistors with β=50. Ignoring the Early effect, the output current is ______ mA (to three decimal places).
    Answer and solution

    Answer: 0.962 mA (±0.002)

    Both transistors carry the same collector current IC, and their two base currents 2IC/β are taken from the reference node: Iref=IC(1+2/β). So Iout=IC=1.001.04=0.962 mA.

    Why people get this wrong: Counting only one base current (1/1.02), or forgetting the base currents entirely.

  25. NATHard

    A common-emitter amplifier runs at IC=1.0 mA (VT=25 mV, β large). Its emitter resistance is split: 200 Ω unbypassed, the rest fully bypassed. RC=4.7 kΩ and the output drives a 4.7 kΩ load through a large capacitor. The magnitude of the mid-band voltage gain is ______ (to two decimal places).
    Answer and solution

    Answer: 10.44 (±0.05)

    re=VT/IC=25 Ω. The unbypassed part stays in the emitter for ac: |Av|=RC∥RLre+RE1=235025+200=10.44. The gain is lower than with full bypass (2350/25=94), but it now depends mainly on resistor values, not on the temperature-dependent re.

    Why people get this wrong: Forgetting the load (4700/225=20.9) or the unbypassed resistor (94).

  26. MCQHard

    A BJT differential pair (matched transistors, constant tail current, VT=25 mV) has a differential input voltage vd. To steer 99% of the tail current into one transistor, vd must be about
    1. 25 mV
    2. 58 mV
    3. 700 mV
    4. 115 mV
    Answer and solution

    Answer: D

    The two collector currents follow IC1/IC2=evd/VT (same IS, emitters joined). For 99:1, vd=VTln⁡99=25×4.60=115 mV. So the pair is linear only for |vd| well below VT, and a few hundred millivolts switch it fully, which is why it also serves as a fast current switch (ECL logic).

    Why people get this wrong: 58 mV is VTln⁡10 (a 10:1 split); 700 mV is the turn-on voltage of one junction, irrelevant to the difference.

  27. MSQHard

    Which statements about the maximum theoretical efficiency of power amplifier stages (sine-wave output) are correct?
    1. Class A with a transformer-coupled load: 50%.
    2. Class B push-pull: π/4≈78.5%.
    3. Class B push-pull has no crossover distortion, since one transistor always conducts.
    4. Class A with the load resistor in the collector circuit: 25%.
    Answer and solution

    Answer: A, B, D

    Class A draws its quiescent current all the time; with a series load resistor half the supply voltage sits across it at rest and the best efficiency is 25%; a transformer lets the collector swing to 2VCC, doubling it to 50%. Class B transistors conduct for half a cycle each and draw supply current only when delivering power, giving π/4. But each needs about 0.7 V of drive before it turns on, so near zero crossing neither conducts: crossover distortion, fixed in class AB by a small bias.

    Why people get this wrong: Assuming class B is free of distortion because it is push-pull: the dead band of ±0.7 V is exactly the crossover problem.

  28. NATTop rank

    A common-emitter amplifier has VCC=12 V, RC=2 kΩ, RE=1 kΩ (fully bypassed) and a load RL=2 kΩ coupled through a capacitor. Treating saturation as VCE=0 and taking IE≈IC, the quiescent collector current for the largest symmetric output swing is ______ mA.
    Answer and solution

    Answer: 3 mA (±0.02)

    DC load: Rdc=RC+RE=3 kΩ, so VCEQ=12−3ICQ (kΩ, mA). AC load: RE is bypassed and RL is in parallel with RC, so Rac=1 kΩ. Along the AC load line through Q, VCE can rise by ICQRac before IC reaches zero, and fall by VCEQ before saturation. Symmetric swing needs VCEQ=ICQRac: 12−3ICQ=ICQ, so ICQ=3 mA (=VCC/(Rdc+Rac)). The peak swing is then 3 V.

    Why people get this wrong: Putting Q at the middle of the DC load line (2 mA, VCE=6 V) clips at cut-off first, because the AC load line is steeper.

  29. MCQTop rank

    A silicon BJT is held at a fixed VBE. At fixed collector current, VBE would fall by about 2 mV per ∘C. Using IC∝eVBE/VT with VT≈26 mV (ignore its own small change), by roughly what factor does IC grow when the temperature rises by 30∘C?
    1. about 10
    2. about 2.3
    3. about 1.06
    4. about 60
    Answer and solution

    Answer: A

    A 30∘C rise lowers the VBE needed for the same current by 60 mV. Holding VBE fixed is therefore like raising it by 60 mV at the old temperature: IC grows by e60/26=e2.31≈10. This is why a BJT must never be biased by a fixed VBE, and why an emitter resistor is used.

    Why people get this wrong: 2.3 is the exponent, not the factor; 1.06 treats the change as linear in VBE.

  30. NATTop rank

    A common-emitter stage at IC=1 mA (VT=25 mV, β=100, take β+1=101) has RC=6 kΩ, load RL=3 kΩ, an unbypassed emitter resistor of 200 Ω (the rest of RE is bypassed) and a bias network of 30 kΩ (the divider resistors in parallel). It is driven from a source with internal resistance 10 kΩ. The magnitude of the overall gain vo/vs is ______ (to two decimal places).
    Answer and solution

    Answer: 5.01 (±0.03)

    re=25 Ω. Gain from base to collector: |Av|=(RC∥RL)/(re+200)=2000/225=8.889. Resistance looking into the base: (β+1)(re+200)=101×225=22.73 kΩ. In parallel with the 30 kΩ bias network: Rin=12.93 kΩ. The source divider passes 12.93/(12.93+10)=0.564 of vs. Overall: 8.889×0.564=5.01.

    Why people get this wrong: Forgetting the source divider gives 8.89; forgetting the bias resistors gives 8.889×22.73/32.73=6.17.

← All topics · Timed mock test →