Home / Courses / GATE Physics / Practice / Rotation, rolling and angular momentum

Rotation, rolling and angular momentum

Mechanics and properties of matter · 11 questions and templates for GATE Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MSQExam level

    A fast-spinning top (spin angular momentum Iω, mass m, centre of mass a distance r from the tip) precesses slowly under gravity. In the usual fast-top approximation, which statements are correct?
    1. The precession rate rises as the spin slows down.
    2. The precession rate does not depend on the tilt angle.
    3. Gravity's torque changes the direction of the angular momentum, not its size.
    4. Doubling the spin doubles the precession rate.
    Answer and solution

    Answer: A, B, C

    The torque mgrsin⁡θ is horizontal and perpendicular to L→, so it only swings L→ round (third true). The horizontal part of L→ is Iωsin⁡θ and turns at rate Ω: ΩIωsin⁡θ=mgrsin⁡θ, so Ω=mgr/(Iω). The tilt cancels (second true); Ω∝1/ω, so a slower spin precesses faster (first true, fourth false).
  2. MSQHard

    A solid ball (radius R) is placed on a rough level floor moving forwards at v0 with backspin ω0 (spinning the "wrong way" for rolling). Which statements are correct?
    1. Its angular momentum about a fixed point on the floor stays constant while it skids.
    2. When it finally rolls, its velocity is (5v0−2ω0R)/7 (forward positive).
    3. If ω0R=2.5v0, it ends up at rest.
    4. Its mechanical energy is conserved while it skids.
    Answer and solution

    Answer: A, B, C

    Friction acts along the floor and through any point on it, and gravity and the normal force cancel, so L about a floor point is kept (true). Before: mv0R−25mR2ω0; after: 75mvR. So v=(5v0−2ω0R)/7 (true), zero when ω0R=2.5v0 (true); with more backspin it comes back. Sliding friction dissipates energy (false).
  3. MSQHard

    For a system of particles, which statements are correct?
    1. τ→ext=dL→/dt holds about the centre of mass even when the centre of mass is accelerating.
    2. τ→ext=dL→/dt holds about any accelerating point.
    3. The angular momentum about a fixed point O equals the angular momentum about the centre of mass plus R→cm×MV→cm.
    4. Internal forces that act along the lines joining pairs of particles do not change the total angular momentum.
    Answer and solution

    Answer: A, C, D

    First: true, a special property of the centre of mass (the fictitious force acts at the centre of mass and has no torque about it). Second: false in general; about an arbitrary accelerating point there is an extra term. Third: true (König's theorem for L→). Fourth: true, equal and opposite central pairs have zero total torque.
  4. MCQHard

    A uniform solid cylinder lies on a horizontal plank. The plank is pulled forward with constant acceleration a, and the cylinder rolls on it without slipping. The acceleration of the cylinder's centre (relative to the ground) is
    1. a
    2. a/3
    3. 2a/3
    4. a/2
    Answer and solution

    Answer: B

    Only friction f (forward, at the bottom) acts horizontally: f=Mac. Its torque about the centre gives fR=12MR2α, so αR=2ac, in the sense that moves the bottom forward relative to the centre. No slipping: the bottom point moves with the plank, ac+αR=a, so 3ac=a and ac=a/3. The cylinder moves forward but falls back relative to the plank.

    Why people get this wrong: Saying the cylinder stays put on the plank (a) ignores that friction must also spin it up.

  5. MSQHard

    A rigid dumbbell (two equal masses on a light rod) is fixed to an axle through its centre, with the rod at 45∘ to the axle, and turned at constant angular velocity ω→ along the axle. Which statements are true?
    1. L→ is parallel to ω→ because ω→ is constant
    2. L→ is not parallel to ω→
    3. The bearings must supply a torque even though ω→ is constant
    4. The kinetic energy is 12ω→⋅L→
    Answer and solution

    Answer: B, C, D

    Each mass moves on a circle round the axle, and L→=∑mr→×v→ is perpendicular to the rod, not along the axle. As the dumbbell turns, L→ sweeps round a cone, so dL→/dt≠0: the bearings must apply a torque (this is dynamic imbalance in a wheel). For any rigid body K=12ω→⋅L→. L→∥ω→ only when ω→ lies along a principal axis.

    Why people get this wrong: Constant ω→ does not mean constant L→ unless the rotation is about a principal axis.

  6. NATTop rank

    A uniform 1.2 m rod stands upright on a perfectly smooth floor and is given a tiny nudge. It slides and falls flat. The speed of its centre of mass just before it lands is ______ m/s (g=9.8 m/s², two decimal places).
    Answer and solution

    Answer: 2.97 m/s (±0.02)

    No horizontal force, so the centre falls straight down: y=L2cos⁡θ, v=L2sin⁡θθ˙. Just before landing (θ=90∘), v=L2ω. Energy: mgL2=12mv2+12⋅mL212(2vL)2=23mv2. So v=123gL=1235.28≈2.97 m/s.

    Why people get this wrong: This is not a hinged rod: the bottom slides, so mL2/3 is wrong.

  7. NATTop rank

    A uniform rod (mass M, length 2 m) lies at rest on frictionless ice. A puck of the same mass M slides at 5 m/s perpendicular to the rod, hits one end and sticks. The angular speed of the rod-puck system afterwards is ______ rad/s (two decimal places).
    Answer and solution

    Answer: 3 rad/s (±0.01)

    New centre of mass: L/4 from the rod's centre towards the puck. It moves at v0/2 (momentum). Angular momentum about that point before: the puck passes at distance L/4, so Mv0L/4. Moment of inertia after: rod ML212+M(L4)2=748ML2; puck M(L4)2=348ML2; total 524ML2. ω=Mv0L/45ML2/24=6v05L=3010=3 rad/s.

    Why people get this wrong: Taking angular momentum about the rod's own centre and using ML2/12 forgets that the axis of rotation moves to the new centre of mass.

  8. MCQTop rank

    A thin uniform disc (I3=2I1 about its symmetry axis) is tossed spinning nearly about its symmetry axis at rate ω3, with a slight wobble, and no torque acts. Seen in the body's own frame, the angular velocity vector circles the symmetry axis at the rate
    1. 2ω3
    2. ω3/2
    3. 0
    4. ω3
    Answer and solution

    Answer: D

    Euler's equations for a free symmetric body: I1ω˙1=(I1−I3)ω2ω3 and I1ω˙2=(I3−I1)ω3ω1, with ω3 constant. They give ω¨1=−Ω2ω1 with Ω=I3−I1I1ω3. For a thin disc I3=2I1, so Ω=ω3.

    Why people get this wrong: Mixing up the body-frame rate with the space-frame wobble of the axis (which for a thin disc is about twice the spin).

  9. NATTop rank

    A small uniform solid ball rolls without slipping inside a fixed hemispherical bowl. Its centre moves on a circle of radius R−r=0.5 m. The period of small oscillations about the bottom is ______ s (g=9.8 m/s², three decimal places).
    Answer and solution

    Answer: 1.679 s (±0.003)

    Let ϕ be the angle of the ball's centre from the bottom, so its centre speed is v=(R−r)ϕ˙. Rolling KE =710mv2; potential mg(R−r)(1−cos⁡ϕ)≈12mg(R−r)ϕ2. Energy: 710m(R−r)2ϕ˙2+12mg(R−r)ϕ2, so ω2=5g7(R−r). T=2π7×0.55×9.8≈1.679 s.

    Why people get this wrong: Using the simple-pendulum period 2π(R−r)/g=1.419 s forgets the rotational energy.

  10. NATTop rank

    A uniform ladder 5.0 m long leans at 30∘ to the vertical against a smooth wall on a smooth floor, and is released from rest. It slides down until its top leaves the wall. By then the top has dropped through ______ m (two decimal places).
    Answer and solution

    Answer: 1.44 m (±0.01)

    While in contact, the centre of mass moves on a circle of radius L/2 about the corner: (L2sin⁡θ,L2cos⁡θ), with θ from the vertical. Energy (translation of the centre plus rotation about it): 12(ML24+ML212)θ˙2=MgL2(cos⁡θ0−cos⁡θ), so θ˙2=3gL(cos⁡θ0−cos⁡θ). The wall's push is Mx¨cm; it falls to zero when ddt(cos⁡θθ˙)=0, which gives cos⁡θ=23cos⁡θ0. The top's height falls from Lcos⁡θ0=4.33 m to 23 of that, a drop of 13×4.33=1.44 m.

    Why people get this wrong: The top does not stay on the wall all the way down; it leaves when its height is two thirds of the starting height.

← All topics · Timed mock test →