Home / Courses / GATE Physics / Practice / Magnetic materials: B, H and M

Magnetic materials: B, H and M

Electricity and magnetism · 42 questions and templates for GATE Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQStandard

    A long cylinder is uniformly magnetised along its axis with magnetisation M. Its bound currents are
    1. a volume current M per unit area along the axis
    2. surface currents M (per unit length) on the flat end faces only
    3. zero everywhere, since M→ is uniform
    4. a surface current M per unit length circling the curved surface, and no volume current
    Answer and solution

    Answer: D

    J→b=∇×M→=0 for uniform M→. K→b=M→×nˆ: on the curved side nˆ=sˆ, zˆ×sˆ=ϕˆ, so Kb=M circling round; on the ends nˆ=±zˆ and the cross product is zero. The magnet is equivalent to a solenoid with nI=M.

    Why people get this wrong: Uniform M→ kills the volume current but not the surface current.

  2. MCQStandard

    For the long, uniformly magnetised rod with no free current, far from its ends, H→ inside is
    1. M→
    2. −M→
    3. zero
    4. M→/3
    Answer and solution

    Answer: C

    H→=B→/μ0−M→=M→−M→=0. Near the ends of a finite rod, H→ is not zero: it points backwards, against M→ (the demagnetising field).

    Why people get this wrong: Assuming H→ always points along B→.

  3. MSQStandard

    At the boundary between two magnetic materials with no free surface current, which field components are continuous?
    1. The normal component of B→
    2. The tangential component of H→
    3. The tangential component of B→
    4. The normal component of H→
    Answer and solution

    Answer: A, B

    ∇⋅B→=0 (a pillbox) makes B⟂ continuous. ∇×H→=J→f with no free surface current (a thin loop) makes H∥ continuous. The other two jump by the ratio of permeabilities.

    Why people get this wrong: This is the mirror of the dielectric rules (D⟂, E∥), with B→ playing D→ and H→ playing E→.

  4. NATExam level

    A sphere is uniformly magnetised with M=1.0×105 A/m. The magnetic field B inside it is ______ mT (to one decimal place).
    Answer and solution

    Answer: 83.8 mT (±0.8)

    The bound surface current Kb=Msin⁡θϕˆ is that of a spinning charged sphere and gives a uniform field inside: B→=23μ0M→=23(1.2566×10−6)(105)=8.38×10−2 T.

    Why people get this wrong: Using μ0M (the long rod). The sphere's shape gives 23 of that.

  5. MCQExam level

    Inside a uniformly magnetised sphere (no free current), H→ equals
    1. −M→/3
    2. +M→/3
    3. 23M→
    4. zero
    Answer and solution

    Answer: A

    H→=B→/μ0−M→=23M→−M→=−13M→. Inside a magnet H→ points backwards: this is the demagnetising field, with demagnetising factor 13 for a sphere (0 for a long rod, 1 for a thin disc magnetised across).

    Why people get this wrong: Taking H→ parallel to B→, which fails inside permanent magnets.

  6. MSQExam level

    In a region filled with a uniform linear magnetic material of susceptibility χm carrying free current density J→f, which statements are correct?
    1. ∇×H→=J→f
    2. ∇⋅B→=0
    3. J→b=χmJ→f
    4. ∇⋅H→=0 everywhere, including at the material's surface
    Answer and solution

    Answer: A, B, C

    ∇×H→=J→f in any static situation, and ∇⋅B→=0 always. With M→=χmH→ and χm constant, J→b=∇×M→=χm∇×H→=χmJ→f. But ∇⋅H→=−∇⋅M→, which is not zero where M→ changes suddenly, as at a surface.

    Why people get this wrong: Uniform material is the key: in non-uniform material J→b has an extra ∇χm×H→ part.

  7. NATExam level

    An iron core (μr=2000) has a mean path length of 0.50 m with an air gap of 1.0 mm cut in it. A winding of 200 turns carries 1.0 A. Neglecting fringing, the field in the gap is ______ T (to three decimal places).
    Answer and solution

    Answer: 0.201 T (±0.002)

    B is the same in iron and gap (normal component continuous, no fringing). Ampère for H: Bμ0μrl+Bμ0g=NI, so B=μ0NIl/μr+g=(1.2566×10−6)(200)2.5×10−4+1.0×10−3=0.201 T.

    Why people get this wrong: Ignoring the 1 mm gap because it is short. Its reluctance is four times that of the whole half-metre of iron.

  8. MCQExam level

    Field lines in air meet the flat surface of a soft iron block (μr=1000) at 45∘ to the normal. Inside the iron the lines
    1. run almost parallel to the surface
    2. run almost along the normal
    3. continue at 45∘
    4. bend to about 22∘ from the normal
    Answer and solution

    Answer: A

    B⟂ and H∥ continuous give tan⁡θ2tan⁡θ1=μ2μ1, so tan⁡θ2=1000, θ2=89.94∘: almost along the surface. Run backwards, lines leaving iron into air come out almost perpendicular to the iron surface, which is why iron pole faces behave like magnetic "equipotentials".

    Why people get this wrong: Expecting the lines to straighten towards the normal in the denser medium, as light does.

  9. NATExam level

    Above its Curie point, a ferromagnet follows the Curie-Weiss law χ=C/(T−θ). Its susceptibility is 0.010 at 1100 K and 0.005 at 1150 K. The constant θ is ______ K.
    Answer and solution

    Answer: 1050 K (±1)

    Dividing: 0.0100.005=1150−θ1100−θ=2, so 1150−θ=2200−2θ and θ=1050 K. Then C=0.010×50=0.50 K.

    Why people get this wrong: Using Curie's law C/T, which would give inconsistent C values.

  10. MCQExam level

    A long cylinder (axis z) has magnetisation M→=ksϕˆ in cylindrical coordinates, where k is a constant. The bound volume current density is
    1. kzˆ
    2. kϕˆ
    3. 2kzˆ
    4. zero
    Answer and solution

    Answer: C

    (∇×M→)z=1s∂∂s(sMϕ)=1sdds(ks2)=2k. Other components vanish. So J→b=2kzˆ. On the surface K→b=M→×sˆ=−kRzˆ; total current 2kπR2−kR⋅2πR=0, as for any bound current crossing a section.

    Why people get this wrong: Forgetting the factor 1/s and the s inside the derivative (the curvilinear curl), which gives k.

  11. NATExam level

    A paramagnet has 1.0×1028 moments per m3, each of magnitude one Bohr magneton (9.27×10−24 J/T), free to point in any direction. Using the classical Curie law χ=μ0Nμ2/(3kBT), its susceptibility at 300 K is ______ ×10−5 (to two decimal places).
    Answer and solution

    Answer: 8.7 $10^{-5}$ (±0.09)

    χ=μ0Nμ23kBT=(1.2566×10−6)(1028)(9.27×10−24)23(1.381×10−23)(300)=1.081×10−241.243×10−20=8.70×10−5.

    Why people get this wrong: Forgetting μ0 (SI volume susceptibility needs it) or the factor 3 from averaging cos2⁡θ.

  12. MCQExam level

    A long cylinder of radius R (axis z) has magnetisation M→=M0sRzˆ, with s the distance from the axis. Its bound currents are
    1. J→b=−M0Rϕˆ inside and K→b=M0ϕˆ on the surface
    2. J→b=0 and K→b=M0ϕˆ
    3. J→b=+M0Rϕˆ and K→b=−M0ϕˆ
    4. J→b=−M0Rzˆ and K→b=0
    Answer and solution

    Answer: A

    J→b=∇×M→. In cylindrical coordinates, for M→=Mz(s)zˆ, (∇×M→)ϕ=−dMzds=−M0R. On the curved surface K→b=M→×nˆ=M0zˆ×sˆ=M0ϕˆ. Check: per unit length the volume current is ∫0R(−M0/R)ds=−M0, which cancels the surface current +M0, as it must for bound currents.

    Why people get this wrong: Writing J→b=0 as for uniform magnetisation; any variation of Mz across the cylinder gives a volume current.

  13. MSQExam level

    Which statements about the auxiliary field H→=B→/μ0−M→ are true (static fields)?
    1. ∮H→⋅dl→ equals the free current through the loop
    2. ∇⋅H→=−∇⋅M→
    3. H→ is zero wherever there is no free current
    4. In a linear material, B→=μ0μrH→
    Answer and solution

    Answer: A, B, D

    Ampère's law with bound currents removed gives ∇×H→=J→f, the integral form being the first statement. Since ∇⋅B→=0, ∇⋅H→=−∇⋅M→, which is non-zero at the ends of a bar magnet. So H→ need not vanish where Jf=0: a bar magnet has an H→ field inside and outside with no free current at all. For a linear medium M→=χmH→ and B→=μ0(1+χm)H→.

    Why people get this wrong: Concluding from ∇×H→=J→f that H→ is fixed by free currents alone; its divergence matters too.

  14. NATHard

    A toroidal iron core (μr=800, linear) has a mean circumference of 0.40 m and a 2.0 mm air gap. A 400-turn winding is to produce 0.50 T in the gap. The current needed is ______ A (to two decimal places).
    Answer and solution

    Answer: 2.48 A (±0.03)

    Iron path l=0.40−0.002=0.398 m. NI=Bμ0(lμr+g)=0.501.2566×10−6(4.975×10−4+2.0×10−3)=994 A-turns, so I=994/400=2.48 A.

    Why people get this wrong: Dropping the iron term entirely gives 1.99 A; here it is a fifth of the total, not negligible.

  15. MCQHard

    Outside a uniformly magnetised sphere of radius R and magnetisation M→, the field is
    1. zero, since all bound current is on the surface
    2. that of a point dipole m→=43πR3M→ at the centre, exactly
    3. that of a point dipole only far away (r≫R)
    4. uniform, equal to 23μ0M→
    Answer and solution

    Answer: B

    The surface current Kb=Msin⁡θ makes exactly a dipole field outside (the same as a spinning charged shell), with total moment = magnetisation × volume =43πR3M→. "Exactly" is the special property of the sphere; other shapes have higher multipoles close up.

    Why people get this wrong: Thinking the dipole form is only a far-field approximation; for a sphere it is exact at every r>R.

  16. MSQHard

    Which statements about the B-H hysteresis loop of a ferromagnet are correct?
    1. The remanence is the value of B when H has been brought back to zero.
    2. The coercivity is the reverse H needed to bring B to zero.
    3. Materials with thin loops and small coercivity suit transformer cores.
    4. Good permanent magnets need small coercivity, so that they are easy to magnetise.
    Answer and solution

    Answer: A, B, C

    Remanence and coercivity are defined where the loop crosses the axes. Transformers cycle 50 times a second, so they need small loop area (soft materials). A permanent magnet must resist demagnetisation by stray fields and its own H→, so it needs large coercivity (hard materials, wide loops).

    Why people get this wrong: Easy to magnetise also means easy to demagnetise: permanent magnets want the opposite.

  17. NATHard

    A sphere of linear magnetic material with μr=4 is placed in a uniform field B0=0.10 T. The field inside the sphere is ______ T (to two decimal places).
    Answer and solution

    Answer: 0.2 T (±0.005)

    Solving with M→=χmH→ (the magnetic twin of the dielectric sphere): B→in=3μrμr+2B→0=126(0.10)=0.20 T. Check: with H→in=B→0/μ0−M→/3 and M→=3H→in we get Hin=B0/(2μ0) and Bin=μ0μrHin=2B0.

    Why people get this wrong: Using μrB0=0.40 T, the long-needle answer. The sphere's demagnetising field reduces it.

  18. MCQHard

    A long straight wire carrying current I runs along the axis of a long cylinder of radius R made of linear material with susceptibility χm. Inside the material, at distance s from the axis (s<R), the field is
    1. μ0I2πs
    2. μ0(1+χm)I2πs
    3. μ0(1+χm)Is2πR2
    4. μ0I2π(1+χm)s
    Answer and solution

    Answer: B

    The free current is only in the wire, so H=I/(2πs) by Ampère. B=μ0(1+χm)H. The extra field comes from a bound current χmI along the wire's surface (the inner edge of the material); a return bound current −χmI flows on the outer surface, so outside B=μ0I/(2πs) again.

    Why people get this wrong: The s/R2 form is for current spread through the cylinder; here the free current is only on the axis.

  19. NATHard

    Spin-12 moments of one Bohr magneton sit in a field of 1.0 T at 300 K, each either along or against the field. The net fractional alignment (N↑−N↓)/N is ______ ×10−3 (to two decimal places).
    Answer and solution

    Answer: 2.24 $10^{-3}$ (±0.03)

    The two energies are ∓μBB, so by Boltzmann N↑−N↓N=tanh⁡μBBkBT. Here μBBkBT=9.27×10−244.14×10−21=2.24×10−3, and tanh⁡x≈x for small x. Only about 2 in 1000 moments are effectively aligned at room temperature.

    Why people get this wrong: Using the classical Langevin result x/3, which is for moments that can point in any direction.

  20. MCQHard

    Inside a short bar magnet (no free current), how do B→ and H→ point relative to the magnetisation M→?
    1. Both along M→
    2. Both against M→
    3. B→ along M→, H→ against M→
    4. B→ against M→, H→ along M→
    Answer and solution

    Answer: C

    With no free current, ∮H→⋅dl→=0. Outside, H→=B→/μ0 runs from N to S; to close the loop with zero total, H→ inside must run from N to S too, i.e. against M→. B→ forms closed loops (∇⋅B→=0), running S to N inside, along M→: B→=μ0(H→+M→) with |H→|<|M→|.

    Why people get this wrong: Drawing H→ lines as closed loops like B→ lines. H→ lines start and end on the poles.

  21. MCQHard

    A thin flat disc of permanent-magnet material is uniformly magnetised with M→ perpendicular to its faces. Near the centre of the disc, inside it,
    1. B→≈μ0M→ and H→≈0
    2. B→≈23μ0M→ and H→≈−13M→
    3. B→≈0 and H→≈−M→
    4. B→≈0 and H→≈0
    Answer and solution

    Answer: C

    The bound current is Kb=M round the thin rim; seen from the centre of a wide, thin disc it is a short loop far away, so B≈μ0Mt/2R→0. Then H→=B→/μ0−M→≈−M→. Equivalently, the faces carry pole densities ±M like a parallel-plate capacitor, which give H=−M between them (demagnetising factor 1). A long needle magnetised along its length is the opposite case: H≈0, B≈μ0M; the sphere is in between (23, −13).

    Why people get this wrong: Using the long-rod result for every shape; the shape decides how much of μ0M survives as B.

  22. MCQHard

    In the Langevin (Larmor) picture of diamagnetism, a gas of n atoms per unit volume, each with Z electrons of mean square orbit radius ⟨r2⟩ (measured perpendicular to the field), has a susceptibility that
    1. is negative, proportional to nZ⟨r2⟩, and independent of temperature
    2. is negative and proportional to nZ⟨r2⟩/T
    3. is positive and proportional to nZ⟨r2⟩
    4. is negative and proportional to nZ/⟨r2⟩
    Answer and solution

    Answer: A

    Switching on B changes each electron's orbital speed (by induction) so that the orbit gains an extra moment −e2⟨r⟂2⟩4mB, opposing the field. Summing: χ=−μ0nZe2⟨r⟂2⟩4m (or μ0nZe2⟨r2⟩6m with the full 3D mean). Nothing here involves thermal alignment, so χ does not depend on T. Bigger orbits mean a bigger induced moment.

    Why people get this wrong: Borrowing the 1/T of Curie paramagnetism; that comes from thermal competition with permanent moments, which a diamagnetic atom does not have.

  23. MSQHard

    Which statements about antiferromagnets and ferrimagnets are correct?
    1. Below its Néel temperature an antiferromagnet has a large spontaneous magnetisation.
    2. The susceptibility of an antiferromagnet has a maximum (a cusp) at the Néel temperature.
    3. Above the Néel temperature an antiferromagnet follows χ=C/(T+θ) with θ>0.
    4. A ferrimagnet has a net spontaneous magnetisation because its two opposed sublattices have unequal moments.
    Answer and solution

    Answer: B, C, D

    A is false: the two sublattices are equal and opposite, so the net spontaneous moment is zero. B: below TN the ordered sublattices resist the field, so χ falls on cooling; above TN it falls on heating; the peak is at TN. C: the mean field of an antiferromagnet opposes alignment, shifting the Curie law to C/(T+θ). D: unequal sublattices (as in magnetite) leave a net moment.

    Why people get this wrong: Mixing up the signs: ferromagnets follow C/(T−θ), antiferromagnets C/(T+θ).

  24. NATHard

    A closed magnetic ring has two sections of the same cross-section: steel (μr=1500, path length 40 cm) and ferrite (μr=300, path length 10 cm). A winding of 250 turns carries 0.40 A. Treating the materials as linear and ignoring leakage, the field B in the ring is ______ mT (to the nearest whole number).
    Answer and solution

    Answer: 209 mT (±1)

    The flux (so B) is the same in both sections. Ampère for H: H1l1+H2l2=NI with Hi=B/(μ0μi), so B=μ0NIl1/μ1+l2/μ2=(1.257×10−6)(100)2.667×10−4+3.333×10−4=0.209 T =209 mT. The short ferrite piece takes more of the "reluctance" than the long steel part.

    Why people get this wrong: Averaging the permeabilities by length (gives μr=1260 and 316 mT); reluctances in series add as l/μ.

  25. NATHard

    An iron ring (μr=2000, linear) of mean path length 0.50 m has a 1.0 mm air gap. The magnetic energy stored in the gap divided by that stored in the iron is ______ (to one decimal place; ignore fringing).
    Answer and solution

    Answer: 4 (±0.05)

    The same B crosses the iron and the gap. Energy density is B22μ0μr: μr times larger in the gap. With the same area, energies go as density times length: EgapEiron=μrgl=2000×0.0010.50=4.0. A 1 mm gap holds 80% of the energy, which is why electromagnets work on their gaps.

    Why people get this wrong: Thinking the iron holds most energy because it has the larger volume or larger μ; for fixed B larger μ means less energy.

  26. NATHard

    Water has χm=−9.0×10−6 and density 1000 kg/m³. To float a drop of water in the vertical field of a strong magnet (the trick used to levitate a frog), the product BdBdz at the drop must reach about ______ T²/m (take g=9.8 m/s²).
    Answer and solution

    Answer: 1368 T²/m (±10)

    A weakly magnetic material (|χm|≪1) has energy −χm2μ0B2 per unit volume, so it feels a force per unit volume χm2μ0∇(B2)=χmμ0B∇B. For a diamagnet (χm<0) this pushes towards weaker field. Balancing weight per unit volume: |χm|μ0BdBdz=ρg, so BdBdz=μ0ρg|χm|=1.257×10−6×1000×9.89.0×10−6=1.37×103 T²/m (e.g. about 16 T with a gradient of 85 T/m).

    Why people get this wrong: Dropping the factor 1μ0 or the square: the force depends on the gradient of B2, not of B.

  27. MSQHard

    Which statements about ferromagnets in the Weiss mean-field picture are true?
    1. Below the Curie temperature a magnetisation exists inside each domain even with no applied field
    2. The spontaneous magnetisation falls continuously to zero as the temperature rises to the Curie point
    3. Above the Curie point the susceptibility follows χ=C/(T−θ) with θ>0
    4. The Weiss "molecular field" comes from the magnetic dipole fields of neighbouring atoms
    Answer and solution

    Answer: A, B, C

    In the mean-field model each moment feels λM in addition to the applied field; below TC this self-consistent field keeps the moments aligned spontaneously, and Ms falls smoothly to zero at TC (a continuous transition). Above TC, the model gives the Curie-Weiss law with θ=TC>0. The needed λM is of order 1000 T, far bigger than any dipole field (about 1 T); its true origin is the quantum exchange interaction.

    Why people get this wrong: Taking the molecular field literally as a magnetic field from neighbouring dipoles; it is far too large for that.

  28. MCQHard

    A transformer designed for 50 Hz is run at 60 Hz with the same peak flux density. Compared with before, the hysteresis loss and the eddy-current loss (power) each change by a factor of
    1. 1.44 and 1.2
    2. 1.2 and 1.2
    3. 1 and 1.44
    4. 1.2 and 1.44
    Answer and solution

    Answer: D

    With the same peak B the loop is the same, so the hysteresis energy per cycle is unchanged; the power goes as the number of cycles per second, ×6050=1.2. Eddy currents are driven by the induced emf, which is proportional to fBpeak; the power (∝ emf²) goes as f2, so ×1.44.

    Why people get this wrong: Treating both losses alike; hysteresis is per cycle, eddy loss grows with the square of the frequency.

  29. NATTop rank

    A ring of permanent-magnet material, of mean circumference 0.30 m, is uniformly magnetised round the ring with M=8.0×105 A/m (treat M as fixed). A thin radial gap of 3.0 mm is cut in it. Neglecting fringing, the field in the gap is ______ T (to three decimal places).
    Answer and solution

    Answer: 0.995 T (±0.005)

    No free current: ∮H→⋅dl→=Hm(l−g)+Hgg=0. B is continuous across the gap faces: B=μ0Hg=μ0(Hm+M). Eliminating: Bgμ0=−(Bμ0−M)(l−g), so B=μ0Ml−gl=(1.0053)(0.99)=0.995 T.

    Why people get this wrong: Taking B=μ0M in the gap (no reduction) or B=0 (no free current). The gap creates a small backward H in the magnet.

  30. MSQTop rank

    For a uniformly magnetised sphere with no free current, which statements are correct?
    1. Inside, B→ is parallel to M→.
    2. Inside, H→ is antiparallel to M→.
    3. Outside, the field is exactly that of a point dipole.
    4. ∇⋅H→=0 everywhere, including on the surface.
    Answer and solution

    Answer: A, B, C

    B→in=23μ0M→ and H→in=−13M→. Outside it is an exact dipole of moment 43πR3M→. On the surface M→ drops to zero abruptly, so ∇⋅H→=−∇⋅M→ is a surface "magnetic charge" σm=M→⋅nˆ, not zero.

    Why people get this wrong: Using ∇⋅B→=0 for H→. H→ behaves like an electrostatic field of magnetic "poles".

← All topics · Timed mock test →