Home / Courses / GATE Physics / Practice / Damped and forced oscillations, resonance

Damped and forced oscillations, resonance

Oscillations, waves and optics · 28 questions and templates for GATE Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MSQExam level

    A lightly damped oscillator is driven at exactly ω=ω0. Which statements are correct?
    1. The velocity amplitude is the largest it can be for any ω.
    2. The average power absorbed from the driver is the largest it can be.
    3. The displacement amplitude is the largest it can be.
    4. The velocity is in phase with the driving force.
    Answer and solution

    Answer: A, B, D

    Velocity amplitude ωA=(F0/m)/(ω02/ω−ω)2+4β2, largest when ω=ω0 (A), where the velocity is in phase with the force (D) and so the power 12F0v0cos⁡(0) is largest (B). The displacement amplitude peaks a little lower, at ω02−2β2 (C false).

    Why people get this wrong: Displacement resonance and velocity (energy) resonance are at slightly different frequencies.

  2. MSQExam level

    An underdamped oscillator at rest is suddenly driven by F0cos⁡ωt. Which statements are correct?
    1. The transient part of the motion decays as e−βt.
    2. The steady state does not depend on the initial conditions.
    3. With light damping and ω close to ω0, beats can be seen while the transient lasts.
    4. The steady-state amplitude depends on the initial displacement.
    Answer and solution

    Answer: A, B, C

    The full solution is the steady state plus a free damped oscillation Ce−βtcos⁡(ωdt+α); C and α carry the initial conditions and die away (A, B; D false). While both parts are present, frequencies ω and ωd add and beat (C).
  3. MCQExam level

    For a lightly damped oscillator, the two frequencies at which the absorbed power is half its maximum differ by
    1. β/2
    2. 4β
    3. 2β
    4. β
    Answer and solution

    Answer: C

    Half power occurs where (ω02−ω2)2=(2βω)2, i.e. ω02−ω2=±2βω. The positive roots are ω=∓β+ω02+β2, so ω2−ω1=2β=ω0/Q (exactly, in fact).
  4. NATExam level

    A resonator has natural frequency 800 Hz and Q=40. Driven at 805 Hz with the same force amplitude, its steady-state displacement amplitude is ______ times its amplitude when driven at exactly 800 Hz (two decimal places).
    Answer and solution

    Answer: 0.89 (±0.006)

    A(ω)=F0/m(ω02−ω2)2+4β2ω2 with 2β=ω0/Q. Near resonance, ω02−ω2≈2ω0(ω0−ω), so A(ω)A(ω0)≈11+(2QΔf/f0)2=11+(2×40×5/800)2=11.25=0.89. The exact formula gives 0.889.

    Why people get this wrong: The half-power points are at Δf=f0/(2Q)=10 Hz; 5 Hz off is only halfway there.

  5. NATHard

    1 kg mass, ω0=10 rad/s, β=1 s−1, driven by a force of amplitude 1 N at whatever frequency makes the displacement amplitude largest. That largest amplitude is ______ mm (to one decimal place).
    Answer and solution

    Answer: 50.3 mm (±0.2)

    At ωr2=ω02−2β2: (ω02−ωr2)2+4β2ωr2=4β4+4β2(ω02−2β2)=4β2(ω02−β2). So Amax⁡=F0/(2mβω02−β2)=1/(299)=0.05025 m =50.3 mm.

    Why people get this wrong: Evaluating at ω0 instead gives F0/(2mβω0)=50.0 mm, close but not the maximum.

  6. MCQHard

    The steady-state displacement amplitude of a driven damped oscillator has a maximum at some non-zero driving frequency only if
    1. always, for any damping
    2. Q>1/2
    3. Q>1/2
    4. Q>1
    Answer and solution

    Answer: B

    ωr2=ω02−2β2 must be positive: β<ω0/2, i.e. Q=ω0/(2β)>1/2. For heavier damping the amplitude just falls steadily from F0/k as ω rises.

    Why people get this wrong: Q>1/2 is the condition for free oscillation (underdamping), which is weaker.

  7. NATHard

    The displacement amplitude of a driven oscillator peaks at 0.98ω0. Its quality factor is ______ (to two decimal places).
    Answer and solution

    Answer: 3.55 (±0.03)

    ωr2/ω02=1−2(β/ω0)2=0.9604, so (β/ω0)2=0.0198 and β/ω0=0.1407. Q=ω0/(2β)=1/0.2814=3.55.
  8. MSQHard

    The average power absorbed by a driven damped oscillator is P(ω)=F022m2βω2(ω02−ω2)2+4β2ω2. Which statements are correct?
    1. The curve is exactly symmetric about ω0 on a linear frequency axis.
    2. Its maximum is exactly at ω=ω0, for any damping.
    3. Its full width at half maximum is exactly 2β, for any damping.
    4. P→0 as ω→0.
    Answer and solution

    Answer: B, C, D

    Divide top and bottom by ω2: P∝2β/[(ω02/ω−ω)2+4β2], largest when ω=ω0 (B). Half maximum when |ω02/ω−ω|=2β, whose positive roots differ by exactly 2β (C). At ω→0 the numerator ω2→0 (D). A is false: the curve is symmetric in ln⁡ω (the roots multiply to ω02), not in ω; it looks symmetric only near a sharp peak.

    Why people get this wrong: Many students "know" the width is 2β only approximately; for the power curve it is exact, while the symmetry is the approximate part.

  9. MCQHard

    A block on a spring slides on a rough horizontal floor (coefficient of kinetic friction μ). Its amplitude decreases
    1. by an amount proportional to the amplitude squared
    2. only during the first half cycle
    3. by the same fraction every cycle
    4. by the same amount, 4μmg/k, every cycle
    Answer and solution

    Answer: D

    In each half cycle the friction force has constant size μmg, so the motion is SHM about a shifted centre ±μmg/k. Each half swing ends 2μmg/k closer to the origin than it began, so the amplitude falls by 4μmg/k per full cycle: a linear, not exponential, decay.

    Why people get this wrong: "The same fraction" (exponential decay) is the signature of viscous damping, −bx˙.

  10. NATHard

    A 0.5 kg block on a spring (k=20 N/m) on a floor with μ=0.1 (same value for static and kinetic friction; g=9.8 m/s2) is released from rest 20 cm from the unstretched position. It finally stops ______ cm from the unstretched position (to one decimal place).
    Answer and solution

    Answer: 0.4 cm (±0.05)

    μmg/k=0.49/20=0.0245 m, so each half swing loses 2×0.0245=0.049 m. Turning points: +0.200, −0.151, +0.102, −0.053, +0.004 m. At each of the first four the spring force (kx≥1.06 N) beats the friction limit 0.49 N, so the block moves on. At 0.004 m the spring force is only 0.08 N, so it stays: 0.4 cm.

    Why people get this wrong: Stopping as soon as the amplitude is "small": you must compare k|x| with μmg at each turning point.

  11. MCQHard

    For an undamped oscillator (b=0) driven by F0cos⁡ωt, the steady-state response as ω is swept through ω0
    1. has an amplitude that grows without limit near ω0, and a phase that jumps suddenly from 0 to π
    2. has a finite peak at ω0 and a phase that rises smoothly through π/2
    3. has zero amplitude at ω0
    4. is the same at all frequencies
    Answer and solution

    Answer: A

    A=(F0/m)/(ω02−ω2): positive (in phase) below ω0, negative (phase π) above, and infinite at ω0 itself, where the amplitude actually grows linearly in time. Damping is what rounds this off into a finite peak with a smooth phase change.
  12. NATHard

    In steady state an oscillator with b=0.2 kg/s moves with amplitude 0.1 m at ω=5 rad/s. The work done by the driving force in one cycle is ______ J (to four decimal places).
    Answer and solution

    Answer: 0.0314 J (±0.0005)

    In steady state the driver's work per cycle equals the energy dissipated: ∮bx˙2dt=bω2A2⋅(T/2)=bω2A2⋅π/ω=πbωA2=π×0.2×5×0.01=0.0314 J.
  13. MCQHard

    An underdamped oscillator of mass m at rest at x=0 receives a sharp impulse J at t=0. For t>0 its displacement is
    1. Jme−βtsin⁡ωdt
    2. Jmωdsin⁡ω0t
    3. Jmωde−βtsin⁡ωdt
    4. Jmω0e−βtcos⁡ωdt
    Answer and solution

    Answer: C

    The impulse gives x(0)=0, x˙(0)=J/m. The free solution x=Ce−βtsin⁡ωdt meets x(0)=0, and x˙(0)=Cωd=J/m fixes C=J/(mωd). This is the Green's function of the oscillator (times J).

    Why people get this wrong: The option (J/m)e−βtsin⁡ωdt has the wrong units: J/m is a speed, so it must be divided by a frequency.

  14. MSQHard

    A lightly damped oscillator (mass m, damping constant b, natural frequency ω0) is driven by F0cos⁡ωt. Which statements about the steady state are true?
    1. The average absorbed power is largest at ω=ω0
    2. At ω=ω0 the velocity is in phase with the force
    3. At ω=ω0 the displacement is in phase with the force
    4. The full width of the power curve between its half-power points is Δω=b/m
    Answer and solution

    Answer: A, B, D

    ⟨P⟩=12F0v0cos⁡(phase between F and v); at ω0 the velocity amplitude is largest and in phase with the force, so the power is largest. The displacement then lags the force by π/2. Near resonance ⟨P⟩∝1(ω−ω0)2+(b/2m)2, so the half-power points are at ω0±b2m, a full width b/m (and Q=ω0/Δω).

    Why people get this wrong: At resonance it is the velocity, not the displacement, that keeps step with the force.

  15. MCQHard

    A damped oscillator is driven at various frequencies with the same force amplitude. Its time-averaged kinetic energy in the steady state is largest when the driving frequency is
    1. ω02−2β2
    2. ω0, whatever the damping
    3. ω02−β2
    4. ω02+2β2
    Answer and solution

    Answer: B

    The velocity amplitude is ωA=F0/m(ω02−ω2)2/ω2+4β2, largest when ω02−ω2=0. So the kinetic energy (and the power absorbed) peaks exactly at ω0. The displacement amplitude, and with it the potential energy, peaks lower, at ω02−2β2.

    Why people get this wrong: Displacement resonance and velocity resonance are at different frequencies when there is damping.

  16. NATHard

    A very lightly damped oscillator with ω0=10 rad/s starts at rest and is driven by F0cos⁡(9t). Until the transient dies out, its amplitude swells and shrinks periodically. The period of this swelling is ______ s (two decimal places).
    Answer and solution

    Answer: 6.28 s (±0.01)

    Starting from rest, the motion is the steady-state response at 9 rad/s plus a free (transient) oscillation at about 10 rad/s, of similar size at first. Two oscillations at nearby frequencies beat: their sum swells and shrinks with period 2π/|ω0−ω|=2π/1=6.28 s. As the free part decays, the beats fade and only the steady response is left.

    Why people get this wrong: 2π/ω0 or 2π/ω (about 0.6 s) is the period of the fast oscillation inside the envelope, not of the swelling.

  17. MSQHard

    A damped oscillator is in steady state under the force F0cos⁡ωt. Which statements about phases are correct?
    1. At ω=ω0 the velocity is in phase with the force
    2. Below resonance the displacement lags the force by less than 90∘
    3. Far above resonance the displacement is nearly opposite in phase to the force
    4. The power absorbed is largest where the displacement lags the force by 45∘
    Answer and solution

    Answer: A, B, C

    tan⁡ϕ=2βωω02−ω2 for the lag ϕ of x behind F. Below ω0, ϕ<90∘; at ω0, ϕ=90∘, so the velocity (which leads x by 90∘) is in phase with F; far above, ϕ→180∘. The power ⟨Fx˙⟩ is largest when F and x˙ are in phase, i.e. at ϕ=90∘, not 45∘.

    Why people get this wrong: 45∘ marks the half-power points (for light damping), not the peak.

  18. NATTop rank

    An oscillator with Q=5 is released from rest. The fraction of its initial energy left after exactly three damped periods is ______ (to four decimal places).
    Answer and solution

    Answer: 0.0226 (±0.0005)

    Released from rest, x=x0e−βt(cos⁡ωdt+(β/ωd)sin⁡ωdt) and x˙∝e−βtsin⁡ωdt. After each full period Td the mass is again at rest, so all energy is 12kx2 with x=x0e−βTd. Energy ratio after three periods: e−6βTd. With β/ω0=1/(2Q)=0.1 and ωd=ω00.99: βTd=2π(0.1)/0.99499=0.6315, so the fraction is e−3.789=0.0226.

    Why people get this wrong: Using ω0 instead of ωd in the period gives e−1.2π=0.0230: close, but outside the tolerance.

  19. MSQTop rank

    A lightly damped oscillator is in steady state under F0cos⁡ωt. Which statements are correct?
    1. The time-averaged kinetic and potential energies are equal only when ω=ω0.
    2. For ω<ω0 the average potential energy exceeds the average kinetic energy.
    3. The displacement amplitude is largest exactly at ω=ω0.
    4. At the two half-power frequencies the displacement lags the force by π/4 and 3π/4.
    Answer and solution

    Answer: A, B, D

    ⟨KE⟩=14mω2A2 and ⟨PE⟩=14mω02A2: equal only at ω=ω0 (A), and PE>KE below it (B). C is false: the displacement peak is at ω02−2β2. D: at the half-power points |ω02−ω2|=2βω, so tan⁡ϕ=±1: ϕ=π/4 below and 3π/4 above resonance.
  20. NATTop rank

    For an oscillator with Q=1, the displacement amplitude when driven at ω0 is a fraction f of the largest displacement amplitude (reached at ωr). The value of f is ______ (to three decimal places).
    Answer and solution

    Answer: 0.866 (±0.003)

    A(ω0)=F0/(2mβω0) and Amax⁡=F0/(2mβω02−β2). Ratio =1−(β/ω0)2=1−1/(4Q2)=3/4=0.866.

    Why people get this wrong: For high Q this ratio is almost 1, which is why the two resonances are often treated as the same; at Q=1 they are not.

  21. NATTop rank

    The oscillator x¨+2x˙+100x=cos⁡ωt (SI) is driven at ω=12 rad/s. In steady state the displacement lags the force by ______ degrees (one decimal place).
    Answer and solution

    Answer: 151.4 degrees (±0.2)

    With x=Acos⁡(ωt−δ): tan⁡δ=2βωω02−ω2=2×12100−144=−0.545. Above resonance the denominator is negative while the numerator is positive, so δ lies between 90∘ and 180∘: δ=180∘−28.6∘=151.4∘.

    Why people get this wrong: Taking the calculator's tan−1⁡(−0.545)=−28.6∘; the lag always lies in (0,180∘).

  22. MCQTop rank

    For a driven damped oscillator with Q=1/2, the steady-state displacement amplitude as a function of driving frequency
    1. peaks at ω0/2
    2. peaks at ω0
    3. becomes infinite at ω0
    4. has no peak at any non-zero frequency; it falls steadily from ω=0
    Answer and solution

    Answer: D

    The displacement peak is at ωr=ω02−2β2. With Q=ω02β=12, β=ω0/2, so ωr=0. For this damping and any heavier, the amplitude is largest for a static force and decreases as ω rises. (This "maximally flat" response is the Butterworth filter shape.)

    Why people get this wrong: Assuming every driven oscillator shows a resonance peak; strong enough damping removes it.

  23. NATTop rank

    The peak of a driven oscillator's displacement-amplitude curve is exactly twice its displacement for a very slow (static) drive of the same force amplitude. Without assuming light damping, its quality factor Q=ω0/(2β) is ______ (three decimal places).
    Answer and solution

    Answer: 1.932 (±0.003)

    With ζ=β/ω0=1/(2Q), the peak (at ω2=ω02−2β2) is Amax⁡F0/k=12ζ1−ζ2. Setting this to 2: 4ζ2(1−ζ2)=14, so ζ2=1−3/22=0.06699 and ζ=0.2588. Then Q=1/(2ζ)=1.932.

    Why people get this wrong: The light-damping rule "peak/static = Q" gives 2, which is not accurate when Q is this small.

← All topics · Timed mock test →