Home / Courses / Engineering entrance / Practice / Elasticity of solids

Elasticity of solids

Class 11 · 260 questions and templates for Engineering entrance, in order from warm-up to top rank. Check each answer, then read the full solution.

New to this topic? Read the lesson first: Elasticity of solids.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. NATWarm-up

    A force of 500 N pulls along the length of a rod whose cross-section is 2×10−4 m2. Find the stress in the rod (in kPa).
    Answer and solution

    Answer: 2500 kPa

    Stress =F/A=500/(2×10−4)=2.5×106 Pa =2500 kPa.
  2. MCQWarm-up

    Longitudinal strain is defined as
    1. force per unit area
    2. change in length divided by original length
    3. original length divided by change in length
    4. change in volume divided by pressure
    Answer and solution

    Answer: B

    Strain =ΔL/L: a ratio of two lengths. It has no unit and no dimensions. The other options describe stress, an inverted ratio and the inverse of the bulk modulus.
  3. MCQWarm-up

    The SI unit of Young's modulus is
    1. Nm−2 (pascal)
    2. Nm−1
    3. Nm
    4. no unit
    Answer and solution

    Answer: A

    Y=stress/strain. Strain has no unit, so Y has the unit of stress, Nm−2 = Pa.
  4. MCQWarm-up

    Hooke's law says that, within the elastic limit,
    1. strain is inversely proportional to stress
    2. stress is proportional to the square of strain
    3. stress is independent of strain
    4. stress is directly proportional to strain
    Answer and solution

    Answer: D

    The straight part of the stress-strain graph from the origin is Hooke's law. The slope is the modulus of elasticity.
  5. NATWarm-up

    A wire 2 m long stretches by 2 mm under a load. Find the strain in units of 10−3.
    Answer and solution

    Answer: 1

    Strain =ΔL/L=2×10−3/2=1×10−3. In units of 10−3 the answer is 1.
  6. MCQWarm-up

    Which of these has the largest Young's modulus?
    1. rubber
    2. lead
    3. steel
    4. human bone
    Answer and solution

    Answer: C

    Steel is about 2×1011 Pa, bone about 1010 Pa, lead about 1.6×1010 Pa and rubber only about 106 to 107 Pa. A material with larger Y is stiffer.
  7. MCQWarm-up

    Which modulus of elasticity is meaningful for a liquid?
    1. Young's modulus
    2. bulk modulus
    3. modulus of rigidity
    4. Poisson's ratio
    Answer and solution

    Answer: B

    A liquid takes the shape of its container, so it has no shear modulus. It resists a change of volume, so it has a bulk modulus. A liquid in a container is not stretched along a line, so Y does not apply either.
  8. MCQWarm-up

    The dimensional formula of Young's modulus is
    1. ML−1T−2
    2. MLT−2
    3. ML2T−2
    4. M0L0T0
    Answer and solution

    Answer: A

    Same as stress or pressure: force over area =MLT−2/L2=ML−1T−2.
  9. MCQWarm-up

    A body is perfectly elastic if it
    1. never changes its shape
    2. breaks when a force is applied
    3. keeps the new shape after the force is removed
    4. regains its original size and shape completely when the deforming force is removed
    Answer and solution

    Answer: D

    That is the definition. Quartz and phosphor bronze are close to perfectly elastic. A body that keeps the new shape is called plastic (putty is an example).
  10. NATWarm-up

    A wire carries a stress of 4×108 Nm−2 and shows a strain of 2×10−3. Find its Young's modulus (in units of 1011 Nm−2).
    Answer and solution

    Answer: 2

    Y=σ/ε=4×108/(2×10−3)=2×1011 Pa, so the answer is 2.
  11. MCQWarm-up

    The bulk modulus is the ratio of
    1. tangential force to area
    2. longitudinal stress to longitudinal strain
    3. the pressure change to the fractional change in volume (with a minus sign)
    4. lateral strain to longitudinal strain
    Answer and solution

    Answer: C

    B=−ΔP/(ΔV/V). The minus sign makes B positive, because volume falls when pressure rises. Options 2 and 3 are Y and Poisson's ratio; the first is a shear stress.
  12. MCQWarm-up

    Twisting a metal rod about its length is mainly opposed by its
    1. bulk modulus
    2. modulus of rigidity (shear modulus)
    3. Young's modulus
    4. compressibility
    Answer and solution

    Answer: B

    Twisting slides each layer over the next one. This is a shear, so the shear (rigidity) modulus matters.
  13. MCQWarm-up

    The compressibility of a material is
    1. the reciprocal of its bulk modulus
    2. equal to its bulk modulus
    3. equal to its Young's modulus
    4. the reciprocal of its density
    Answer and solution

    Answer: A

    k=1/B=−1VdVdP. A highly compressible material has a small bulk modulus. Gases are far more compressible than liquids.
  14. NATWarm-up

    A steel wire of cross-section 1 mm2 has Y=2×1011 Nm−2. What load (in N) produces a strain of 10−3?
    Answer and solution

    Answer: 200 N

    F=YAε=2×1011×10−6×10−3=200 N. Remember 1 mm2=10−6 m2.
  15. MCQWarm-up

    The elastic limit of a wire is the stress beyond which
    1. the wire breaks at once
    2. stress becomes proportional to strain
    3. the wire becomes perfectly elastic
    4. the wire does not return to its original length when the load is removed
    Answer and solution

    Answer: D

    Beyond the elastic limit some permanent set remains (plastic deformation). The wire does not have to break there; breaking happens at a much larger stress.
  16. MCQWarm-up

    Steel is more elastic than rubber because, for the same stress,
    1. steel shows a larger strain
    2. steel shows no strain at all
    3. steel shows a smaller strain
    4. rubber has a larger Young's modulus
    Answer and solution

    Answer: C

    In physics, "more elastic" means a larger modulus (a bigger restoring stress for the same strain). Steel has Y∼2×1011 Pa and so a much smaller strain than rubber.
  17. MCQWarm-up

    Poisson's ratio of a material is
    1. measured in Nm−2
    2. a pure number
    3. measured in Nm−1
    4. measured in metre
    Answer and solution

    Answer: B

    It is lateral strain divided by longitudinal strain: a ratio of two strains, so it has no unit. For most materials it lies between 0 and 0.5.
  18. MCQWarm-up

    The elastic energy stored per unit volume in a stretched wire is
    1. 12×stress×strain
    2. stress × strain
    3. 12×stress/strain
    4. stress2×strain
    Answer and solution

    Answer: A

    Work done =12FΔL (the area under the force-extension line). Dividing by volume AL gives 12FAΔLL.
  19. MCQWarm-up

    A wire stretches by 1 mm under a load of 2 kg. Within the elastic limit, a load of 6 kg (same wire) will stretch it by
    1. 2 mm
    2. 6 mm
    3. 9 mm
    4. 3 mm
    Answer and solution

    Answer: D

    Extension is proportional to load: ΔL∝F. Tripling the load triples the extension: 3×1=3 mm.
  20. MCQWarm-up

    Stress produced in a wire depends on
    1. the load and the length only
    2. the length and the material only
    3. the load and the area of cross-section, but not on the length
    4. the material only
    Answer and solution

    Answer: C

    Stress is F/A. The length of the wire does not enter. (Extension does depend on the length, strain does not.)
  21. NATStandard

    A steel wire of length 2 m and diameter 1 mm carries a 20 kg load. Find its extension (in mm, 2 decimals). Y=2×1011 Nm−2, g=9.8 ms−2.
    Answer and solution

    Answer: 2.5 mm (±0.02)

    F=20×9.8=196 N. A=πd2/4=7.854×10−7 m2. ΔL=FLAY=196×27.854×10−7×2×1011=2.5 mm.

    Why people get this wrong: Use the area from the diameter: radius is half of 1 mm.

  22. MCQStandard

    A wire of diameter 2 mm supports a load of 150 N. The stress in it is
    1. 191 MPa
    2. 47.7 MPa
    3. 23.9 MPa
    4. 95.5 MPa
    Answer and solution

    Answer: B

    A=πd2/4=π×(2×10−3)2/4=3.14×10−6 m2. σ=150/3.14×10−6=47.7 MPa. Using the diameter as the radius would give a quarter of this, and using πd2 gives a quarter too.

    Why people get this wrong: Radius, not diameter, in πr2.

  23. NATStandard

    A wire is stretched by 2 mm by a load of 100 N applied slowly within the elastic limit. How much elastic energy (in J) is stored in it?
    Answer and solution

    Answer: 0.1 J (±0.001)

    U=12FΔL=0.5×100×2×10−3=0.1 J. Using FΔL would give 0.2 J, which is the work done by a load that drops freely and falls through 2 mm. Half of that is lost as heat and sound.

    Why people get this wrong: The factor 12 (the force grows from zero).

  24. MCQStandard

    A wire of Y=2×1011 Pa is stretched to a strain of 10−3. The elastic energy stored per unit volume is
    1. 1 × 105 J m-3
    2. 2 × 105 J m-3
    3. 1 × 108 J m-3
    4. 50000 J m-3
    Answer and solution

    Answer: A

    u=12Yε2=0.5×2×1011×10−6=1×105 Jm−3.
  25. NATStandard

    Two steel wires of lengths 1.5 m and 0.5 m, both of cross-section 1 mm2, are joined end to end and a 100 N load is hung from the free end. Find the total extension (in mm). Y=2×1011 Pa.
    Answer and solution

    Answer: 1 mm (±0.005)

    In series, both wires carry the same force (100 N). Total extension =F(L1+L2)AY=100×210−6×2×1011=10−3 m =1 mm.
  26. MCQStandard

    A steel wire and a brass wire have the same length and area. They hang side by side and together carry a 300 N load, both stretching equally. If Ysteel=2×1011 Pa and Ybrass=1×1011 Pa, the steel wire carries
    1. 100 N
    2. 150 N
    3. 250 N
    4. 200 N
    Answer and solution

    Answer: D

    Equal extension means F/(AY)⋅L is the same, so F∝Y. Shares: steel : brass = 2 : 1. Steel carries 23×300=200 N.

    Why people get this wrong: The stiffer wire takes the larger share.

  27. NATStandard

    A steel rod is clamped rigidly at both ends at 20 °C and then heated to 70 °C. Find the thermal stress in it (in MPa). Y=2×1011 Pa, α=1.2×10−5 K−1.
    Answer and solution

    Answer: 120 MPa

    The rod tries to expand by a strain αΔT but cannot. Stress =YαΔT=2×1011×1.2×10−5×50=1.2×108 Pa =120 MPa.
  28. MCQStandard

    The bulk modulus of water is 2.2×109 Pa. When the pressure on it rises by 2×107 Pa, its volume decreases by (in percent)
    1. 0.00909 %
    2. 9.09 %
    3. 0.909 %
    4. 11 %
    Answer and solution

    Answer: C

    ΔVV=ΔPB=2×1072.2×109=9.09×10−3=0.909%.
  29. NATStandard

    A uniform steel wire 100 m long hangs from a support. Find its extension due to its own weight alone (in mm, 2 decimals). ρ=7800 kgm−3, Y=2×1011 Pa, g=9.8 ms−2.
    Answer and solution

    Answer: 1.91 mm (±0.02)

    The stress at distance x from the free end is ρgx, so ΔL=∫0LρgxYdx=ρgL22Y=7800×9.8×1042×2×1011=1.91 mm.

    Why people get this wrong: The factor 2: the weight acts like a load of half of the wire at the end.

  30. NATStandard

    A rod with Poisson's ratio 0.3 is stretched to a longitudinal strain of 2×10−3. Find the lateral (sideways) contraction strain, in units of 10−4.
    Answer and solution

    Answer: 6

    Lateral strain =σ× longitudinal strain =0.3×2×10−3=6×10−4.

← All topics