Home / Courses / CSIR NET Physics / Practice / Waveguides, transmission lines, cavities and optical fibres

Waveguides, transmission lines, cavities and optical fibres

Electricity and magnetism · 86 questions and templates for CSIR NET Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    Which kind of wave can a hollow, perfectly conducting rectangular waveguide NOT carry?
    1. TE10
    2. TM11
    3. TEM
    4. TE20
    Answer and solution

    Answer: C

    A TEM mode would need a transverse field that is both curl-free and divergence-free in the cross-section, i.e. a 2D electrostatic field inside a single closed conductor. That conductor is an equipotential, so the field is zero. TEM needs two separate conductors (coax, parallel plates).

    Why people get this wrong: The coaxial line, not the hollow guide, carries TEM.

  2. MCQWarm-up

    The dominant mode (lowest cutoff) of a hollow rectangular guide with broad side a and narrow side b<a is
    1. TM11
    2. TE10
    3. TE01
    4. TM10
    Answer and solution

    Answer: B

    fc=c2(m/a)2+(n/b)2 is smallest for (m,n)=(1,0) when a>b: fc=c/2a. TM modes need m,n≥1, so TM11 is higher and TM10 does not exist.

    Why people get this wrong: TE01 has cutoff c/2b, higher because b<a.

  3. NATWarm-up

    An air-filled rectangular guide has inner dimensions 2.5 cm by 1.0 cm. The cutoff frequency of its TE10 mode is ______ GHz (to two decimal places).
    Answer and solution

    Answer: 6 GHz (±0.03)

    fc,10=c2a=3.0×1082×0.025=6.00 GHz. The cutoff wavelength is 2a=5 cm: half a wavelength must fit across the broad side.

    Why people get this wrong: Using the narrow side b gives 15 GHz, the TE01 cutoff.

  4. MCQWarm-up

    A mode is driven at a frequency below its cutoff frequency. Along the guide its fields
    1. travel with phase velocity below c
    2. travel with group velocity above c
    3. stay constant in amplitude
    4. decay exponentially without travelling (an evanescent mode)
    Answer and solution

    Answer: D

    kz2=k2−kc2<0 below cutoff, so kz=iα and the fields go as e−αz with no travelling phase. In a lossless guide this is reactive: no power is absorbed, it is reflected back.

    Why people get this wrong: Below cutoff there is no propagation at any speed.

  5. MCQWarm-up

    Which of these modes does NOT exist in a rectangular waveguide?
    1. TE01
    2. TE20
    3. TM10
    4. TE11
    Answer and solution

    Answer: C

    TM modes have Ez∝sin⁡(mπx/a)sin⁡(nπy/b) (it must vanish on all four walls). With n=0 this is identically zero, and with Ez=0 and Hz=0 there is no field at all. TE modes have Hz∝cos⁡(mπx/a)cos⁡(nπy/b), which allows one index to be zero.

    Why people get this wrong: TE can have one zero index; TM cannot have any.

  6. MCQWarm-up

    The cutoff wavelength of the TE10 mode of a rectangular guide of broad side a is
    1. a
    2. 2a
    3. a/2
    4. 2b
    Answer and solution

    Answer: B

    λc=c/fc=c/(c/2a)=2a. The field Ey∝sin⁡(πx/a) is half a wavelength of the transverse standing wave across the broad side.

    Why people get this wrong: 2b is the TE01 cutoff wavelength.

  7. MCQWarm-up

    As a filter for signals, a hollow metal waveguide behaves as a
    1. low-pass filter
    2. band-stop filter
    3. high-pass filter
    4. all-pass filter (every frequency gets through)
    Answer and solution

    Answer: C

    Every mode of a hollow guide has a cutoff frequency; below the lowest cutoff (that of the dominant mode) nothing propagates and fields die away exponentially. Above it signals pass. So the guide passes high frequencies and blocks low ones. (Higher modes join in at higher frequencies, which limits the useful single-mode band, but they do not block anything.)

    Why people get this wrong: A hollow pipe cannot carry a TEM wave, so unlike a coaxial cable it carries nothing at low frequency, not even dc.

  8. NATStandard

    A 10 GHz signal travels in the TE10 mode of an air-filled guide whose TE10 cutoff is 5 GHz. The guide wavelength is ______ cm (to two decimal places; take c=3.0×108 m/s).
    Answer and solution

    Answer: 3.46 cm (±0.02)

    λ=c/f=3.0 cm. λg=λ1−(fc/f)2=3.00.75=3.46 cm, longer than in free space.

    Why people get this wrong: The guide wavelength is longer than λ, not shorter.

  9. NATStandard

    A 9.0 GHz signal travels in the TE10 mode of an air-filled guide with a=2.5 cm. Its group velocity is ______ ×108 m/s (to two decimal places).
    Answer and solution

    Answer: 2.24 ×10⁸ m/s (±0.02)

    fc=c/2a=6.00 GHz. vg=c1−(fc/f)2=3.0×108×1−(6/9)2=3.0×108×0.745=2.24×108 m/s.

    Why people get this wrong: The phase velocity c/0.745=4.0×108 m/s exceeds c; the group velocity, which carries energy, does not.

  10. MSQStandard

    For a propagating mode in a hollow, air-filled waveguide, which statements are true?
    1. The phase velocity exceeds c
    2. The group velocity is less than c
    3. The product of phase and group velocities is c2
    4. The phase velocity tends to zero as f→fc
    Answer and solution

    Answer: A, B, C

    ω2=ωc2+c2kz2 (the same form as a plasma), so vp=c/1−(fc/f)2>c, vg=c1−(fc/f)2<c and vpvg=c2. As f→fc, vp→∞ and vg→0.

    Why people get this wrong: At cutoff it is the group velocity that vanishes; the phase velocity blows up.

  11. NATStandard

    An air-filled guide is 2.5 cm by 1.0 cm. Only the TE10 mode propagates from 6.0 GHz up to the next cutoff. That upper frequency is ______ GHz (to one decimal place).
    Answer and solution

    Answer: 12 GHz (±0.06)

    Next candidates: TE20 at c/a=12.0 GHz and TE01 at c/2b=15.0 GHz. The lower, 12.0 GHz, ends the single-mode band. Choosing a≈2b makes TE20 and TE01 arrive together and gives the widest single-mode octave.

    Why people get this wrong: Checking only TE01 misses TE20, which comes first when a>2b.

  12. MCQStandard

    For the TE10 mode of a rectangular guide (0≤x≤a across the broad side, 0≤y≤b), the electric field is
    1. along x, varying as cos⁡(πx/a)
    2. along z, largest at the walls
    3. along y, varying as sin⁡(πy/b)
    4. along y, varying as sin⁡(πx/a) and uniform in y
    Answer and solution

    Answer: D

    TE10 has Hz∝cos⁡(πx/a), and from it Ey∝sin⁡(πx/a), Hx∝sin⁡(πx/a), with no y dependence. Ey is parallel to the side walls x=0,a and vanishes there, as a tangential E must; it is largest in the centre.

    Why people get this wrong: The index 1 counts half-waves along x; the field points along y.

  13. MCQStandard

    The wave impedance Et/Ht of a TE mode in an air-filled guide at frequency f above its cutoff fc is
    1. η01−(fc/f)2
    2. η0/1−(fc/f)2
    3. η0
    4. η0fc/f
    Answer and solution

    Answer: B

    For TE modes ZTE=ωμ0/kz=η0k/kz=η0/1−(fc/f)2, larger than η0. For TM modes ZTM=kz/(ωϵ0)=η01−(fc/f)2, smaller.

    Why people get this wrong: TE and TM impedances are swapped forms; TE goes to infinity at cutoff.

  14. NATStandard

    A guide with a=2.5 cm is completely filled with polyethylene (ϵr=2.25). Its TE10 cutoff frequency is ______ GHz (to two decimal places).
    Answer and solution

    Answer: 4 GHz (±0.02)

    In the filling the wave speed is c/ϵr=c/1.5, so fc=c2aϵr=6.001.5=4.00 GHz. The cutoff wavelength in vacuum terms grows by ϵr.

    Why people get this wrong: Dividing by ϵr rather than its square root.

  15. MCQStandard

    Which structure can carry a wave with zero cutoff frequency?
    1. A hollow rectangular guide
    2. A hollow circular guide
    3. A coaxial line
    4. A hollow guide filled with dielectric
    Answer and solution

    Answer: C

    A coaxial line has two conductors, so it supports a TEM mode whose transverse field is the 2D electrostatic field between them; TEM has kz=ω/v at every frequency, no cutoff. Hollow guides (filled or not) have one conductor and only TE and TM modes with non-zero cutoffs.

    Why people get this wrong: A dielectric filling lowers the cutoff but never to zero.

  16. NATStandard

    A coaxial cable has a ratio of outer to inner conductor radii of 3.6 and a polyethylene filling (ϵr=2.25). Its characteristic impedance is ______ Ω (to one decimal place).
    Answer and solution

    Answer: 51.2 Ω (±0.3)

    L′=μ02πln⁡ba and C′=2πϵln⁡(b/a), so Z0=L′/C′=η02πϵrln⁡ba=601.5ln⁡3.6=40×1.281=51.2 Ω.

    Why people get this wrong: Use the natural logarithm, not log10⁡.

  17. MSQStandard

    For a step-index optical fibre with core index n1 and cladding index n2<n1, in air, which statements are true?
    1. The numerical aperture is n12−n22
    2. The largest acceptance half-angle θa in air satisfies sin⁡θa=NA
    3. A larger core radius allows more guided modes
    4. The fibre is single-mode when V>2.405
    Answer and solution

    Answer: A, B, C

    The steepest guided ray meets the core-cladding wall at θc, so it makes 90∘−θc with the axis. Snell at the end face: sin⁡θa=n1sin⁡(90∘−θc)=n1cos⁡θc=n12−n22. The number of modes grows with V=2πaλNA. Single-mode operation needs V<2.405 (the first zero of J0).

    Why people get this wrong: Single mode is for small V, below 2.405.

  18. NATStandard

    A step-index fibre has core index 1.48 and cladding index 1.46. Its numerical aperture is ______ (to three decimal places).
    Answer and solution

    Answer: 0.242 (±0.002)

    NA=n12−n22=2.1904−2.1316=0.0588=0.242, an acceptance half-angle of 14.0∘ in air.

    Why people get this wrong: n1−n2=0.02 is not the numerical aperture.

  19. MCQStandard

    A 75 Ω antenna is connected to a lossless 50 Ω line. The voltage standing-wave ratio on the line is
    1. 1.2
    2. 1.5
    3. 2.0
    4. 3.0
    Answer and solution

    Answer: B

    Γ=ZL−Z0ZL+Z0=25125=0.2, and VSWR=1+|Γ|1−|Γ|=1.20.8=1.5. The reflected power fraction is |Γ|2=4%.

    Why people get this wrong: 1.2 is 1+|Γ|, not the VSWR.

  20. MCQStandard

    An air-filled guide is completely filled with a dielectric of ϵr=4. Every mode's cutoff frequency is
    1. doubled
    2. unchanged
    3. quartered
    4. halved
    Answer and solution

    Answer: D

    fc=12μϵ(m/a)2+(n/b)2∝1/ϵr, so it is halved. That is how dielectric-loaded guides are made smaller for the same band.

    Why people get this wrong: The cutoff goes as 1/ϵr, not 1/ϵr.

  21. MCQStandard

    As the operating frequency rises far above a mode's cutoff, its guide wavelength λg
    1. grows without limit
    2. tends to 2a
    3. approaches the free-space wavelength
    4. tends to zero faster than λ
    Answer and solution

    Answer: C

    λg=λ/1−(fc/f)2→λ as f/fc→∞: the bouncing plane waves travel almost along the axis, and the guide hardly matters.

    Why people get this wrong: λg grows without limit near cutoff, not far above it.

  22. NATStandard

    Two wide parallel metal plates 1.0 cm apart have the space between them filled with a lossless dielectric of ϵr=4.0. The cutoff frequency of their TE1 mode is ______ GHz (to two decimal places).
    Answer and solution

    Answer: 7.49 GHz (±0.03)

    For plates a distance d apart, mode n needs n half-wavelengths across the gap: fc=nv2d with v=c/ϵr in the filling. fc=3.00×1082×0.010×4.0=7.49 GHz, half the air-filled value. The TEM mode still has no cutoff.

    Why people get this wrong: Forgetting that the filling slows the wave, or dividing by ϵr instead of ϵr.

  23. MCQStandard

    A lossless transmission line of characteristic impedance Z0 is terminated in a resistor equal to Z0. Its input impedance is
    1. Z0, whatever the length of the line
    2. zero when the line is a quarter wavelength long
    3. infinite when the line is half a wavelength long
    4. Z0 only when the length is a whole number of half wavelengths
    Answer and solution

    Answer: A

    A matched load absorbs the incident wave completely, so the reflection coefficient is Γ=ZL−Z0ZL+Z0=0. With no reflected wave, V/I=Z0 at every point on the line, so the input impedance is Z0 at any length. The standing-wave ratio is 1.

    Why people get this wrong: The "half-wavelength repeats the load" rule is true, but with a matched load every length repeats it.

  24. NATExam level

    How many distinct modes (counting TE and TM separately) can propagate at 20 GHz in an air-filled guide of 2.5 cm by 1.0 cm?
    Answer and solution

    Answer: 8

    fc=6.00m2+6.25n2 GHz. With n=0: TE10, TE20, TE30 (6, 12, 18 GHz). With n=1: TE01 (15.0), TE11 and TM11 (16.2), TE21 and TM21 (19.2); m=3 gives 23.4 GHz. n=2 starts at 30 GHz. Total 8.

    Why people get this wrong: For m,n≥1 each cutoff carries two modes, TE and TM.

  25. NATExam level

    A 3.0 GHz signal is fed into a 5.0 cm length of air-filled guide with a=2.5 cm (TE10 cutoff 6.0 GHz). By how many decibels is the field attenuated over this length? (to one decimal place)
    Answer and solution

    Answer: 47.3 dB (±0.3)

    α=kc2−k2 with kc=π/a=125.7 m−1 and k=2πf/c=62.9 m−1: α=108.8 Np/m. Over 5 cm, αL=5.44 Np, i.e. 8.686×5.44=47.3 dB. A short length of below-cutoff guide is a strong, frequency-insensitive attenuator.

    Why people get this wrong: Far below cutoff α≈π/a, nearly independent of frequency.

  26. MCQExam level

    The TE10 mode can be built from two plane waves bouncing between the side walls x=0 and x=a. Each makes an angle θ with the guide axis given by
    1. sin⁡θ=2a/λ
    2. cos⁡θ=λ/2a
    3. sin⁡θ=λ/2a
    4. tan⁡θ=a/λ
    Answer and solution

    Answer: C

    The two waves have kx=±ksin⁡θ and must form the standing wave sin⁡(πx/a), so ksin⁡θ=π/a, i.e. sin⁡θ=λ/2a. At cutoff (λ=2a) θ=90∘: the waves bounce straight across and go nowhere. kz=kcos⁡θ gives vg=ccos⁡θ and vp=c/cos⁡θ.

    Why people get this wrong: Measured from the axis, θ grows towards 90∘ at cutoff.

  27. NATExam level

    For the air-filled 2.5 cm by 1.0 cm guide, the cutoff frequency of the lowest TM mode is ______ GHz (to one decimal place).
    Answer and solution

    Answer: 16.2 GHz (±0.08)

    The lowest TM mode is TM11: fc=c2(1/0.025)2+(1/0.010)2=1.5×108×1600+10000=1.5×108×107.7=16.2 GHz.

    Why people get this wrong: TM10 and TM01 do not exist.

  28. MSQExam level

    For propagating modes in an air-filled hollow guide, which statements about the wave impedances are true?
    1. ZTE>η0
    2. ZTM<η0
    3. Both tend to η0 as f→∞
    4. ZTM grows without limit as f→fc
    Answer and solution

    Answer: A, B, C

    ZTE=η0/1−(fc/f)2 and ZTM=η01−(fc/f)2. Far above cutoff both tend to η0. At cutoff ZTE→∞ and ZTM→0; also ZTEZTM=η02 at the same f/fc.

    Why people get this wrong: It is ZTE that diverges at cutoff.

  29. NATExam level

    An air-filled circular guide has inner radius 1.0 cm. Its dominant TE11 mode, with p11′=1.841 (first zero of J1′), has cutoff frequency ______ GHz (to two decimal places).
    Answer and solution

    Answer: 8.78 GHz (±0.04)

    kc=p11′/R, so fc=1.841c2πR=1.841×3.0×1082π×0.010=8.78 GHz. Its cutoff wavelength is 3.41R.

    Why people get this wrong: TE modes use zeros of Jn′; TM modes use zeros of Jn.

  30. MCQExam level

    In a circular guide, the ratio of the TM01 cutoff (first zero of J0: 2.405) to the TE11 cutoff (first zero of J1′: 1.841) is closest to
    1. 1.31
    2. 0.77
    3. 1.00
    4. 2.08
    Answer and solution

    Answer: A

    Cutoff frequencies scale as the Bessel zeros: 2.405/1.841=1.306. So TE11 is dominant, and the single-mode band of a circular guide spans only a factor 1.31, narrower than a rectangular guide's factor 2.

    Why people get this wrong: Inverting the ratio gives 0.77, which would make TM01 dominant.

← All topics · Timed mock test →