Home / Courses / CSIR NET Physics / Practice / Transistors and amplifiers

Transistors and amplifiers

Electronics · 13 questions and templates for CSIR NET Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    In the circuit symbol of an npn bipolar transistor, the arrow on the emitter points
    1. into the transistor
    2. out of the collector
    3. out of the transistor
    4. into the base
    Answer and solution

    Answer: C

    The arrow shows the direction of conventional current through the base-emitter junction when it is forward biased: from p (base) to n (emitter), i.e. out of the npn transistor at the emitter. In a pnp transistor it points in ("Pointing iN Proudly" is one memory aid).

    Why people get this wrong: Following the electron flow: in an npn device electrons enter at the emitter, opposite to the arrow.

  2. NATStandard

    A transistor in its active region carries IC=20 mA with VCE=4.5 V, and IB=0.20 mA with VBE=0.70 V. The power it dissipates is ______ mW (to the nearest whole number).
    Answer and solution

    Answer: 90 mW (±0.5)

    Power is voltage times current at each port: P=VCEIC+VBEIB=(4.5)(20)+(0.70)(0.20)=90+0.14=90.1 mW, almost all of it at the collector junction. That is the figure to compare with the device's power rating (and to use for heat-sink sizing).

    Why people get this wrong: Using VCCIC: the part of the supply dropped across the load resistor is dissipated there, not in the transistor.

  3. MCQStandard

    An n-channel enhancement MOSFET has threshold VT=1.0 V. With VGS=3.0 V and VDS=1.5 V it operates in
    1. the triode (linear) region
    2. saturation
    3. cut-off
    4. breakdown
    Answer and solution

    Answer: A

    The channel exists because VGS>VT. It is pinched off at the drain end only if VDS≥VGS−VT=2.0 V. Here VDS=1.5 V <2.0 V, so the channel is continuous and the device is in the triode region, acting like a voltage-controlled resistor.

    Why people get this wrong: Comparing VDS with VT instead of with the overdrive VGS−VT.

  4. NATExam level

    A common-emitter stage uses collector-feedback bias: RC=2.0 kΩ from VCC=12 V to the collector, and RB=200 kΩ from the collector to the base (emitter grounded). With β=100 and VBE=0.70 V, the collector current is ______ mA (to two decimal places).
    Answer and solution

    Answer: 2.81 mA (±0.03)

    RC carries both IC and IB, i.e. (β+1)IB. Round the loop VCC→RC→RB→ base-emitter: 12=(β+1)IBRC+IBRB+0.70. So IB=11.3(101)(2.0 k)+200 k=11.3402 k=28.1 μA and IC=100IB=2.81 mA. Then VCE=12−101×28.1 μA×2.0 k =6.3 V: active, and if β rises, VC falls and pulls IB down, which stabilises the bias.

    Why people get this wrong: Treating RB as going to VCC (fixed bias) gives 5.65 mA; the feedback comes from the collector voltage.

  5. MSQExam level

    Which statements about temperature effects in a silicon BJT amplifier are correct?
    1. At fixed VBE, the collector current rises as the transistor warms up.
    2. An emitter resistor provides negative feedback that reduces the drift of IC with temperature.
    3. At fixed collector current, VBE falls by roughly 2 mV per kelvin.
    4. Thermal runaway is more likely when the bias circuit has a large emitter resistor.
    Answer and solution

    Answer: A, B, C

    IC≈ISeVBE/VT and IS grows steeply with temperature, so at fixed VBE the current climbs; equivalently, at fixed current VBE falls by about 2 mV/K. If more current heats the junction further, the loop can run away. An emitter resistor turns a rise in IC into a rise in VE, which lowers VBE and opposes the change: a large RE makes runaway less likely, not more.

    Why people get this wrong: Mixing up the two descriptions ("VBE falls" and "IC rises") as if they contradicted each other; they are the same physics at different constraints.

  6. MCQExam level

    A cascode stage (a common-emitter transistor feeding a common-base transistor) is used instead of a single common-emitter stage mainly because it
    1. has a much lower output resistance
    2. keeps the voltage gain of the first transistor near −1, so its base-collector capacitance is hardly Miller-multiplied and the bandwidth is wider
    3. doubles the voltage gain by placing two transistors in parallel
    4. needs no biasing at all
    Answer and solution

    Answer: B

    In a plain CE stage Cμ appears at the input multiplied by (1+|Av|) (Miller effect), which kills the high-frequency response. In the cascode the first transistor's collector sees the low input resistance ≈re of the common-base transistor, so its own gain is about −1 and Cμ is only doubled. The full voltage gain appears at the second collector. A bonus is a very high output resistance.

    Why people get this wrong: Thinking the extra transistor adds gain: the gain is about the same as one CE stage; it is the bandwidth that improves.

  7. NATHard

    A common-emitter amplifier runs at IC=1.0 mA (VT=25 mV, β large). Its emitter resistance is split: 200 Ω unbypassed, the rest fully bypassed. RC=4.7 kΩ and the output drives a 4.7 kΩ load through a large capacitor. The magnitude of the mid-band voltage gain is ______ (to two decimal places).
    Answer and solution

    Answer: 10.44 (±0.05)

    re=VT/IC=25 Ω. The unbypassed part stays in the emitter for ac: |Av|=RC∥RLre+RE1=235025+200=10.44. The gain is lower than with full bypass (2350/25=94), but it now depends mainly on resistor values, not on the temperature-dependent re.

    Why people get this wrong: Forgetting the load (4700/225=20.9) or the unbypassed resistor (94).

  8. MCQHard

    A BJT differential pair (matched transistors, constant tail current, VT=25 mV) has a differential input voltage vd. To steer 99% of the tail current into one transistor, vd must be about
    1. 25 mV
    2. 58 mV
    3. 700 mV
    4. 115 mV
    Answer and solution

    Answer: D

    The two collector currents follow IC1/IC2=evd/VT (same IS, emitters joined). For 99:1, vd=VTln⁡99=25×4.60=115 mV. So the pair is linear only for |vd| well below VT, and a few hundred millivolts switch it fully, which is why it also serves as a fast current switch (ECL logic).

    Why people get this wrong: 58 mV is VTln⁡10 (a 10:1 split); 700 mV is the turn-on voltage of one junction, irrelevant to the difference.

  9. MSQHard

    Which statements about the maximum theoretical efficiency of power amplifier stages (sine-wave output) are correct?
    1. Class A with a transformer-coupled load: 50%.
    2. Class B push-pull: π/4≈78.5%.
    3. Class B push-pull has no crossover distortion, since one transistor always conducts.
    4. Class A with the load resistor in the collector circuit: 25%.
    Answer and solution

    Answer: A, B, D

    Class A draws its quiescent current all the time; with a series load resistor half the supply voltage sits across it at rest and the best efficiency is 25%; a transformer lets the collector swing to 2VCC, doubling it to 50%. Class B transistors conduct for half a cycle each and draw supply current only when delivering power, giving π/4. But each needs about 0.7 V of drive before it turns on, so near zero crossing neither conducts: crossover distortion, fixed in class AB by a small bias.

    Why people get this wrong: Assuming class B is free of distortion because it is push-pull: the dead band of ±0.7 V is exactly the crossover problem.

  10. NATTop rank

    A Widlar current source uses a matched pair with reference current 1.0 mA in the diode-connected transistor and a resistor RE in the emitter of the output transistor. For an output current of 10 μA (VT=25 mV, β large), RE must be ______ kΩ (to two decimal places).
    Answer and solution

    Answer: 11.51 k$\Omega$ (±0.05)

    The bases are joined, so VBE1=VBE2+IORE. With VBE=VTln⁡(I/IS): IORE=VTln⁡IREFIO, so RE=VTIOln⁡IREFIO=0.02510−5ln⁡100=2500×4.605=11.51 kΩ. A plain resistor scaling (V/I) would need far more: the logarithm makes small currents cheap in resistance, which suits ICs.

    Why people get this wrong: Using RE=VBE/IO=70 kΩ, as if the output transistor's VBE were zero.

← All topics · Timed mock test →