Home / Courses / CSIR NET Physics / Practice / Diodes, BJTs, FETs and MOSFETs

Diodes, BJTs, FETs and MOSFETs

Electronics · 77 questions and templates for CSIR NET Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    An n-channel enhancement MOSFET has threshold voltage VT. It operates in saturation (the constant-current region) when VGS>VT and
    1. VDS<VGS−VT
    2. VDS=0
    3. VDS≥VGS−VT
    4. VDS<0
    Answer and solution

    Answer: C

    The channel pinches off at the drain end when the gate-to-drain voltage VGD=VGS−VDS falls to VT, that is when VDS=VGS−VT. For larger VDS the current hardly changes: saturation. For smaller VDS the channel is continuous and the device acts as a voltage-controlled resistor (triode region).

    Why people get this wrong: In a BJT "saturation" means both junctions forward biased and a small VCE; in a MOSFET it means the opposite, a large VDS.

  2. MCQWarm-up

    Why is the DC gate current of a MOSFET practically zero?
    1. The gate is separated from the channel by an insulating oxide layer
    2. The gate-channel junction is reverse biased
    3. The channel has no free carriers until the gate current flows
    4. The source and drain are shorted together
    Answer and solution

    Answer: A

    The gate electrode sits on a thin insulator (SiO2 or a high-κ oxide). It forms a capacitor with the channel: charge on the gate induces the channel charge, but no steady current crosses the insulator. Input resistances of 1012Ω or more are typical.

    Why people get this wrong: A reverse-biased junction is the reason for the JFET, which still has a small leakage current, not the MOSFET.

  3. MCQWarm-up

    An n-channel depletion-mode MOSFET has its gate tied to its source (VGS=0) and a positive VDS. The drain current is
    1. exactly zero, because no gate voltage is applied
    2. non-zero, because a conducting channel exists even at VGS=0
    3. negative, flowing from source to drain
    4. set only by the gate leakage
    Answer and solution

    Answer: B

    A depletion-mode device is made with a doped channel already in place (its threshold voltage is negative for an n-channel device). At VGS=0 it conducts IDSS; a negative gate voltage is needed to turn it off. An enhancement device, with positive VT, would be off at VGS=0.

    Why people get this wrong: Assuming every MOSFET is off at zero gate voltage: that is only true of enhancement devices.

  4. NATWarm-up

    The thermal voltage VT=kBT/q of a diode at 400 K is ______ mV (to two decimal places).
    Answer and solution

    Answer: 34.47 mV (±0.05)

    VT=1.381×10−23×4001.602×10−19=3.447×10−2 V =34.47 mV. It scales linearly with T: 25.85 mV at 300 K times 4/3.

    Why people get this wrong: Using the room-temperature value 25 or 26 mV at any temperature.

  5. MCQWarm-up

    For a BJT in the active region carrying collector current IC, the small-signal transconductance gm=∂IC/∂VBE is
    1. βIC/VT
    2. VT/IC
    3. IC/(βVT)
    4. IC/VT
    Answer and solution

    Answer: D

    IC=ISeVBE/VT, so ∂IC/∂VBE=ISeVBE/VT/VT=IC/VT. It does not depend on β or on the size of the transistor: 40 mA/V for every milliampere at room temperature.

    Why people get this wrong: VT/IC is the emitter resistance re (roughly 1/gm), not gm.

  6. MSQWarm-up

    Which of these devices conduct mainly by majority carriers (unipolar devices)?
    1. Schottky barrier diode
    2. n-channel JFET
    3. Bipolar junction transistor
    4. Enhancement-mode MOSFET
    Answer and solution

    Answer: A, B, D

    In a Schottky diode electrons pass from the semiconductor over the barrier into the metal: majority carriers only, so there is no stored minority charge and it switches fast. JFETs and MOSFETs carry current in a channel of one carrier type. A BJT relies on minority carriers injected into the base: it is bipolar.

    Why people get this wrong: In an enhancement nMOSFET the inversion layer is formed in p-type material, but within the channel the electrons are the carriers that conduct; it is still a unipolar device.

  7. MCQWarm-up

    An ideal diode (ideality factor 1) carries a forward bias current of 2 mA. Taking VT=26 mV, its small-signal (dynamic) resistance is
    1. 13 Ω
    2. 26 Ω
    3. 52 Ω
    4. 0.077 Ω
    Answer and solution

    Answer: A

    From I=I0eV/VT, dI/dV=I/VT, so rd=VT/I=26 mV/2 mA=13 Ω. It is the inverse of the slope of the I-V curve at the bias point, not V/I.

    Why people get this wrong: I/VT=0.077 S is the conductance, not the resistance; and 26 Ω would need an ideality factor of 2.

  8. NATStandard

    A BJT is biased at IC=2.0 mA. Taking VT=25 mV, its transconductance is ______ mA/V.
    Answer and solution

    Answer: 80 mA/V

    gm=IC/VT=2.0 mA/25 mV=0.080 A/V =80 mA/V.

    Why people get this wrong: Dividing by 0.25 V or by 25 V: keep the units straight.

  9. MCQStandard

    A transistor with β=120 is biased at IC=1.5 mA (VT=25 mV). The small-signal input resistance rπ seen at the base is
    1. 25Ω
    2. 2.4 kΩ
    3. 2.0 kΩ
    4. 0.5 kΩ
    Answer and solution

    Answer: C

    gm=1.5/25=0.060 A/V. rπ=β/gm=120/0.060=2000Ω=2.0 kΩ.

    Why people get this wrong: VT/IC≈17Ω is re, the resistance seen at the emitter; the base sees β (more exactly β+1) times more.

  10. NATStandard

    An n-channel JFET has IDSS=12 mA and pinch-off voltage VP=−4 V. In saturation with VGS=−1.5 V the drain current is ______ mA (to two decimal places).
    Answer and solution

    Answer: 4.69 mA (±0.02)

    Shockley's equation: ID=IDSS(1−VGS/VP)2=12(1−0.375)2=12×0.3906=4.69 mA.

    Why people get this wrong: Writing 1+VGS/VP gives 1.3752; both VGS and VP are negative, so their ratio is positive and less than one.

  11. MCQStandard

    A BJT has an Early voltage VA=100 V and runs at IC=1 mA. Its small-signal output resistance ro is about
    1. 100 kΩ
    2. 1 kΩ
    3. 25Ω
    4. 10 MΩ
    Answer and solution

    Answer: A

    The output characteristics, extended backwards, meet the VCE axis at −VA. Their slope is IC/VA, so ro=VA/IC=100 V/1 mA=100 kΩ.

    Why people get this wrong: Ignoring ro altogether is fine only when the load is much smaller than VA/IC.

  12. NATStandard

    An nMOSFET has VT=0.8 V and kn=μnCox(W/L)=2 mA/V2, with ID=12kn(VGS−VT)2 in saturation. At VGS=2.3 V (and a large VDS) the drain current is ______ mA.
    Answer and solution

    Answer: 2.25 mA (±0.01)

    Overdrive Vov=2.3−0.8=1.5 V. ID=12×2×1.52=2.25 mA.

    Why people get this wrong: Dropping the factor 12 doubles the answer; check which convention a question uses for kn.

  13. MCQStandard

    A silicon diode carries a constant forward current. As its temperature rises, its forward voltage
    1. rises by about 2 mV per kelvin
    2. stays the same
    3. falls by about 25 mV per kelvin
    4. falls by about 2 mV per kelvin
    Answer and solution

    Answer: D

    The saturation current IS∝ni2∝T3e−Eg/kBT grows very fast with temperature, so a smaller voltage is needed for the same current. For silicon the net effect is about −2 mV/K, used in diode thermometers.

    Why people get this wrong: Thinking only of VT=kBT/q in the exponent, which alone would make V rise; the growth of IS wins.

  14. MSQStandard

    For a long-channel MOSFET in saturation obeying ID=12knVov2 (with Vov=VGS−VT), which statements are correct?
    1. gm=2ID/Vov
    2. At fixed W/L, gm∝ID
    3. At fixed W/L, gm∝ID, as for a BJT
    4. With channel-length modulation, ID is still exactly independent of VDS
    Answer and solution

    Answer: A, B

    gm=dID/dVGS=knVov=2ID/Vov. Eliminating Vov: gm=2knID∝ID. Only a BJT has gm∝IC. Channel-length modulation adds the factor (1+λVDS), giving a finite ro=1/(λID).

    Why people get this wrong: Both first statements are the same physics written two ways: at fixed current, gm grows as Vov shrinks; at fixed W/L, it grows as ID.

  15. MCQStandard

    The pinch-off voltage VP of an n-channel JFET is the gate-source voltage at which
    1. the gate junction starts to conduct
    2. the depletion layers close the channel completely and the drain current falls to zero
    3. the drain current equals IDSS
    4. avalanche breakdown starts at the drain
    Answer and solution

    Answer: B

    Making the gate more negative widens the depletion layers of the reverse-biased gate junction until they meet across the whole channel: cut-off, ID=0. The same voltage, measured as VDS with VGS=0, marks the start of current saturation.

    Why people get this wrong: At VGS=0 the current is largest (IDSS), not zero.

  16. NATStandard

    An abrupt silicon junction with built-in potential 0.8 V has a depletion capacitance of 20 pF at zero bias. At a reverse bias of 7.2 V its capacitance is ______ pF (to two decimal places).
    Answer and solution

    Answer: 6.32 pF (±0.03)

    For an abrupt junction W∝Vbi+VR and C=εA/W∝(Vbi+VR)−1/2. C=200.8/(0.8+7.2)=200.1=6.32 pF.

    Why people get this wrong: Forgetting Vbi, or using the exponent −1/3 that belongs to a linearly graded junction.

  17. MCQStandard

    An MOS capacitor is built on p-type silicon. When a large positive voltage is applied to the gate, the semiconductor surface is in
    1. accumulation: extra holes gather at the surface
    2. flat-band: no charge at the surface
    3. depletion only, however large the voltage
    4. strong inversion: a thin layer of electrons forms at the surface
    Answer and solution

    Answer: D

    A positive gate first pushes holes away (depletion). Beyond the threshold the surface potential has bent the bands so far that electrons, the minority carriers, gather in a thin inversion layer: this is the channel of an nMOSFET. Negative gate voltage gives accumulation of holes.

    Why people get this wrong: Accumulation needs the gate polarity that attracts the majority carriers: negative for p-type.

  18. MCQStandard

    A silicon abrupt junction at 300 K has NA=1.0×1017 cm−3 on the p side and ND=1.0×1015 cm−3 on the n side, with ni=1.0×1010 cm−3 and kBT/e=25.85 mV. Its built-in potential is closest to
    1. 0.36 V
    2. 0.60 V
    3. 0.71 V
    4. 0.83 V
    Answer and solution

    Answer: C

    Vbi=kBTeln⁡NANDni2=0.02585ln⁡1017×10151020=0.02585ln⁡1012=0.02585×27.63=0.714 V.

    Why people get this wrong: Using only one doping twice (ND2 gives 0.60 V, NA2 gives 0.83 V) or halving the logarithm (0.36 V).

  19. NATStandard

    A MOSFET has a silicon dioxide gate insulator (εr=3.9) of thickness 2.0 nm. Its gate capacitance per unit area Cox is ______ fF/μm2 (to two decimal places). Take ε0=8.854×10−12 F/m.
    Answer and solution

    Answer: 17.27 (±0.2)

    Cox=εrε0/tox=3.9×8.854×10−12/2.0×10−9=1.727×10−2 F/m2. Since 1 F/m2=1015 fF per 1012 μm2=103 fF/μm2, Cox=17.27 fF/μm2.

    Why people get this wrong: The unit change: F/m2 to fF/μm2 is a factor 103, not 1015 or 10−12.

  20. NATExam level

    An nMOSFET with kn=1 mA/V2 and overdrive VGS−VT=2 V is operated at VDS=0.5 V. Using ID=kn[(VGS−VT)VDS−VDS2/2], the drain current is ______ mA (to three decimal places).
    Answer and solution

    Answer: 0.875 mA (±0.005)

    First check the region: VDS=0.5<Vov=2 V, so the device is in the triode region and the formula applies. ID=1×(2×0.5−0.125)=0.875 mA.

    Why people get this wrong: Using the saturation formula would give 2 mA, far too large at such a small VDS.

  21. MSQExam level

    An nMOSFET is used as a voltage-controlled resistor with very small VDS. Which statements are correct?
    1. Its resistance is about rDS=1/[kn(VGS−VT)]
    2. Doubling the overdrive VGS−VT halves the resistance
    3. In this region ID does not depend on VDS
    4. The region requires VDS<VGS−VT
    Answer and solution

    Answer: A, B, D

    For VDS≪Vov the triode formula becomes ID≈knVovVDS: linear in VDS, with slope 1/rDS=knVov. So the resistance falls as the overdrive grows. The triode region is VDS<Vov; independence from VDS is the saturation region.

    Why people get this wrong: The device is ohmic only for small VDS; the VDS2/2 term bends the curve as VDS approaches Vov.

  22. NATExam level

    A MOSFET in saturation carries ID=0.5 mA with overdrive 0.25 V and channel-length modulation parameter λ=0.05 V−1. Its intrinsic voltage gain gmro is ______.
    Answer and solution

    Answer: 160

    gm=2ID/Vov=2×0.5/0.25=4 mA/V. ro=1/(λID)=1/(0.05×0.5 mA)=40 kΩ. gmro=4×40=160. Equivalently 2/(λVov).

    Why people get this wrong: Using gm=ID/Vov (missing the 2) gives 80.

  23. MCQExam level

    A BJT has Early voltage 50 V. At room temperature (VT=25 mV) its intrinsic gain gmro, the largest voltage gain one common-emitter transistor can give, is
    1. 200
    2. 50
    3. 2000
    4. 20 000
    Answer and solution

    Answer: C

    gm=IC/VT and ro=VA/IC, so gmro=VA/VT=50/0.025=2000, independent of the bias current. This is why BJT stages reach gains that need cascodes in MOS technology.

    Why people get this wrong: The bias current cancels; a question that gives IC here is offering a distraction.

  24. MCQExam level

    An ideal diode (ideality factor 1) at 300 K is forward biased well above VT. To increase its current tenfold, its voltage must rise by about
    1. 26 mV
    2. 60 mV
    3. 2.3 mV
    4. 120 mV
    Answer and solution

    Answer: B

    I≈ISeV/VT, so ΔV=VTln⁡(I2/I1)=25.85 mV×ln⁡10=59.5 mV. With ideality factor n it is n×59.5 mV, so 120 mV per decade means n=2.

    Why people get this wrong: 26 mV is a factor of e, not of 10.

  25. MCQExam level

    An npn transistor has VBE=0.75 V and VBC=0.55 V. It is in the
    1. saturation region
    2. active region
    3. cut-off region
    4. reverse-active region
    Answer and solution

    Answer: A

    Both junctions are forward biased (base above both emitter and collector), which is saturation. VCE=VBE−VBC=0.20 V, the typical VCE(sat). Active needs the base-collector junction reverse biased.

    Why people get this wrong: A positive VBC means the collector is below the base: forward bias, not reverse.

  26. MSQExam level

    About a static CMOS inverter (one nMOS, one pMOS) driving another CMOS gate, which statements are correct?
    1. With the input steady at either logic level, it draws almost no supply current
    2. During a transition both transistors conduct briefly, giving a short-circuit current
    3. Its output high level is essentially VDD and its output low level essentially 0 V
    4. Its switching threshold is VDD/2 whatever the sizes of the two transistors
    Answer and solution

    Answer: A, B, C

    In each steady state one transistor is off, so there is no DC path from VDD to ground, and with a gate load (no DC current) the output reaches the rail. While the input passes through mid-range both are on. The threshold depends on the ratio kn/kp; it is VDD/2 only for matched devices with |VTp|=VTn.

    Why people get this wrong: Most CMOS power is dynamic, CVDD2f, not static.

  27. NATExam level

    An n-channel JFET with IDSS=10 mA and VP=−5 V is biased at VGS=−2 V. Its transconductance is ______ mA/V (to two decimal places).
    Answer and solution

    Answer: 2.4 mA/V (±0.01)

    Differentiate ID=IDSS(1−VGS/VP)2: gm=−2IDSSVP(1−VGS/VP)=2×105(1−0.4)=4×0.6=2.40 mA/V.

    Why people get this wrong: gm0=2IDSS/|VP|=4 mA/V applies only at VGS=0.

  28. MCQExam level

    In an nMOSFET, the reverse bias between source and body (VSB>0) is increased. The threshold voltage
    1. decreases, because the body supplies more electrons
    2. is unchanged, because the body is not part of the channel
    3. increases, because more depletion charge must be balanced before inversion
    4. becomes negative
    Answer and solution

    Answer: C

    The depletion region under the channel widens, so its fixed negative charge grows. The gate must supply that extra charge before an inversion layer forms: VT=VT0+γ(2ϕF+VSB−2ϕF) rises. The body acts as a second gate (body transconductance gmb).

    Why people get this wrong: Thinking the body terminal is irrelevant because it carries no current.

  29. MCQExam level

    A heavily doped junction breaks down at about 3 V. The mechanism and the sign of the temperature coefficient of its breakdown voltage are
    1. avalanche multiplication, positive
    2. Zener (band-to-band) tunnelling, negative
    3. avalanche multiplication, negative
    4. thermal runaway, positive
    Answer and solution

    Answer: B

    Heavy doping gives a very thin depletion layer and huge fields, so electrons tunnel from the valence band on one side into the conduction band on the other. A higher temperature shrinks the gap and makes tunnelling easier: negative coefficient. Avalanche breakdown (above about 6 V) has a positive coefficient because phonon scattering shortens the free path; diodes near 5-6 V have almost zero drift.

    Why people get this wrong: Every breakdown diode is sold as a "Zener", but true Zener tunnelling is the low-voltage one.

  30. MCQExam level

    A BJT and a MOSFET (overdrive Vov=0.2 V) carry the same bias current. Taking VT=25 mV, the ratio of the BJT's transconductance to the MOSFET's is
    1. 8
    2. 0.25
    3. 2
    4. 4
    Answer and solution

    Answer: D

    gm,BJT=I/VT and gm,MOS=2I/Vov. Ratio =Vov/(2VT)=0.2/0.05=4. A MOSFET would need Vov=2VT=50 mV (near weak inversion) to match.

    Why people get this wrong: Forgetting the factor 2 in the MOSFET gm gives 8.

← All topics · Timed mock test →