Home / Courses / CSIR NET Physics / Practice / Phase changes and the Clausius-Clapeyron equation

Phase changes and the Clausius-Clapeyron equation

Kinetic theory and thermodynamics · 12 questions and templates for CSIR NET Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. NATExam level

    At a second-order transition at 4.0 K, the molar heat capacity jumps by ΔCP=2.0 J mol−1 K−1 and the volume expansion coefficient by Δα=1.0×10−4 K−1. The molar volume is 1.0×10−5 m3/mol. By Ehrenfest's equation, the slope dP/dT of the transition line is ______ ×108 Pa/K.
    Answer and solution

    Answer: 5 $10^8$ Pa/K (±0.05)

    For a second-order transition S is continuous along the line: ds1=ds2 with ds=(CP/T)dT−vαdP. Subtracting: (ΔCP/T)dT=vΔαdP, so dPdT=ΔCPTvΔα=2.04.0×1.0×10−5×1.0×10−4=5.0×108 Pa/K.

    Why people get this wrong: Clausius–Clapeyron gives 0/0 here, since both L and Δv vanish; Ehrenfest's equations replace it.

  2. MCQExam level

    At fixed temperature, raising the pressure on a substance that has two possible phases favours
    1. the phase with the larger molar entropy
    2. the phase with the larger molar volume
    3. the phase with the smaller molar volume
    4. neither, because pressure does not affect which phase is stable
    Answer and solution

    Answer: C

    (∂g∂P)T=v, so the molar Gibbs energy of each phase rises with pressure at a rate equal to its molar volume. The denser phase (smaller v) rises more slowly and ends up with the lower g. That is why pressure melts ice (water is denser) and turns graphite into diamond.

    Why people get this wrong: The entropy decides what temperature favours (∂g/∂T=−s), not pressure.

  3. MCQExam level

    In Landau theory, F=a(T−Tc)m2+bm4 with a,b>0. Just below Tc, the equilibrium order parameter behaves as
    1. m∝(Tc−T)
    2. m∝(Tc−T)1/2
    3. m∝(Tc−T)1/3
    4. m jumps to a finite value at Tc
    Answer and solution

    Answer: B

    ∂F/∂m=2a(T−Tc)m+4bm3=0 gives m=0 or m2=a(Tc−T)2b. Below Tc the non-zero root has lower F, so m=a(Tc−T)/2b∝(Tc−T)1/2: mean-field exponent β=12 (real fluids and magnets give about 0.33). It starts from zero, so the transition is continuous.

    Why people get this wrong: A jump in m needs a negative m4 coefficient (or a cubic term): that is a first-order transition.

  4. MSQExam level

    Which of these are first-order transitions (with latent heat)?
    1. melting of ice at 1 atm
    2. heating a fluid along an isobar above its critical pressure, from liquid-like to gas-like
    3. iron losing its ferromagnetism at the Curie point in zero field
    4. a type-I superconductor turning normal in a non-zero applied magnetic field
    Answer and solution

    Answer: A, D

    Melting has a latent heat (334 J/g for ice). Above the critical pressure there is no phase boundary at all: properties change smoothly. The Curie point in zero field is continuous: magnetisation goes to zero smoothly and only the heat capacity is singular. A type-I superconductor in a field B<Bc(0) goes normal at Tc(B)<Tc with a latent heat TΔs (the entropy jumps); only at zero field is the transition second order.

    Why people get this wrong: The same material can show a first-order or continuous transition depending on the field or pressure path.

  5. MCQHard

    Along a liquid–vapour coexistence curve, with an ideal vapour and negligible liquid volume, one can show dL/dT=CP,vap−CP,liq (molar). For water, CP,liq=75.3 and CP,vap=33.6 J mol−1 K−1. Near 100∘C the latent heat changes with temperature at a rate of about
    1. −41.7 J mol−1 K−1: it falls as the temperature rises
    2. +41.7 J mol−1 K−1: it rises with temperature
    3. 0: the latent heat is a constant of the substance
    4. −109 J mol−1 K−1, that is −L/T
    Answer and solution

    Answer: A

    Take the derivative of L=TΔs along the curve: dL/dT=Δs+TdΔs/dT. Along the curve ds=(CP/T)dT−(∂v/∂T)PdP; for the ideal vapour (∂v/∂T)P=v/T and dP/dT=L/(Tv), giving TdΔs/dT=ΔCP−L/T. The L/T terms cancel: dL/dT=ΔCP=33.6−75.3=−41.7 J mol−1 K−1. (Measured: water's L falls from 45.0 kJ/mol at 0∘C to 40.7 at 100∘C, about −43 per kelvin.) It keeps falling and reaches zero at the critical point.

    Why people get this wrong: Treating L as a fixed property of the substance is fine over small ranges only.

  6. MCQHard

    Below about 0.3 K, the melting curve of helium-3 has dP/dT<0, although the solid is denser than the liquid. What does this tell you?
    1. The latent heat of fusion is zero there
    2. The Clausius–Clapeyron equation does not apply to quantum liquids
    3. The liquid has a larger molar volume and a larger molar entropy
    4. The solid has a larger molar entropy than the liquid
    Answer and solution

    Answer: D

    dP/dT=Δs/Δv with Δ= liquid − solid. The solid is denser, so Δv>0. A negative slope then needs Δs<0: the solid has more entropy. In solid helium-3 the nuclear spins are disordered (entropy Rln⁡2 per mole) while in the liquid they are ordered by Fermi statistics. Squeezing the liquid into solid therefore absorbs heat and cools it: Pomeranchuk cooling.

    Why people get this wrong: Clausius–Clapeyron holds for any two phases in equilibrium; it is pure thermodynamics.

  7. NATHard

    A Landau free energy per mole is F=a(T−Tc)m2+bm4 with a=2.0 J mol−1 K−1, b=40 J/mol and Tc=100 K. The jump in molar heat capacity at Tc is ______ J mol−1 K−1.
    Answer and solution

    Answer: 5 (±0.05)

    Below Tc, m2=a(Tc−T)/2b and Fmin⁡=−a2(Tc−T)24b; above, F=0. C=−T∂2F∂T2=a2T2b below and 0 above. At Tc: ΔC=a2Tc2b=4×10080=5.0 J mol−1 K−1, larger on the ordered side. No latent heat: entropy is continuous, its slope is not (second order in Ehrenfest's sense).

    Why people get this wrong: Dropping the factor T in C=−T∂2F/∂T2 gives 0.05.

  8. NATHard

    Pure water is supercooled by ΔT=20 K. In classical nucleation theory a spherical ice nucleus grows only if its radius exceeds r∗=2γTmLVΔT. With γ=0.033 J/m2, Tm=273 K and latent heat per volume LV=3.06×108 J/m3, r∗ is ______ nm (two decimal places).
    Answer and solution

    Answer: 2.94 nm (±0.03)

    A nucleus of radius r changes the free energy by ΔG=−43πr3Δg+4πr2γ with Δg=LVΔT/Tm (the bulk gain per volume, from Δg=Δh−TΔs near Tm). The maximum is at r∗=2γ/Δg=2×0.033×2733.06×108×20=2.94×10−9 m. Such a nucleus holds thousands of molecules, which rarely gather by chance; hence deep supercooling of clean water.

    Why people get this wrong: Setting ΔG=0 instead of maximising it gives 3γ/Δg=1.5r∗ (4.41 nm).

  9. NATTop rank

    A type-I superconductor has a critical field μ0Hc(T)=B0(1−T2/Tc2) with B0=0.080 T and Tc=7.2 K. The Gibbs energy per unit volume of the normal state exceeds that of the superconducting state by μ0Hc2/2. Find the latent heat per unit volume absorbed when the sample turns normal in its critical field at T=3.6 K: ______ kJ/m3 (to two decimal places). Take μ0=4π×10−7 T m/A.
    Answer and solution

    Answer: 1.91 kJ/m³ (±0.02)

    Entropy difference: sn−ss=−∂(gn−gs)/∂T=−μ0HcdHc/dT. With μ0Hc=B0(1−t2), t=T/Tc: dHc/dT=−2B0T/(μ0Tc2), so L=T(sn−ss)=2B02μ0t2(1−t2). Here t=0.5: B02/μ0=0.0064/1.2566×10−6=5093 J/m3, and L=2×5093×0.25×0.75=1910 J/m3=1.91 kJ/m3. It is positive because the normal state has more entropy, and it vanishes at T=0 and at T=Tc (where the transition becomes second order).

    Why people get this wrong: Forgetting that Hc itself depends on T: the latent heat comes entirely from dHc/dT.

  10. MCQTop rank

    In Landau theory with a field, F=a(T−Tc)m2+bm4−hm. At the same distance |T−Tc| from the transition, the zero-field susceptibility χ=∂m/∂h above Tc is how many times its value below Tc?
    1. 1
    2. 1/2
    3. 4
    4. 2
    Answer and solution

    Answer: D

    Let t=T−Tc. Equilibrium needs ∂F/∂m=0, i.e. h=2atm+4bm3; differentiating, 1/χ=∂h/∂m=∂2F/∂m2 at the equilibrium m. Above: m=0, 1/χ=2at. Below: m02=−at/2b, so 1/χ=2at+12bm02=2at−6at=4a|t|. Ratio χabove/χbelow=4a|t|/2a|t|=2. Both diverge as |t|−1 (mean-field γ=1).

    Why people get this wrong: Forgetting the curvature added by the m4 term below Tc gives a ratio of 1.

← All topics · Timed mock test →