Home / Courses / CSIR NET Physics / Practice / Operational amplifiers

Operational amplifiers

Electronics · 13 questions and templates for CSIR NET Physics, in order from warm-up to top rank. Check each answer, then read the full solution.

Loading questions… (they need JavaScript; nothing you type is sent anywhere)

Written questions with solutions

The same questions as a list, so you can print them or read without the practice box. Templates (fresh numbers) appear only in the practice box above.

  1. MCQWarm-up

    The two "golden rules" for an ideal op-amp circuit (the inputs draw no current, and the two input voltages are equal) can be used
    1. whenever the op-amp is powered
    2. only when there is negative feedback and the output is not saturated
    3. only when there is positive feedback
    4. only for ac signals
    Answer and solution

    Answer: B

    The rule "no input current" is a property of the device. The rule V+=V− is not: it is what negative feedback achieves, by adjusting the output until the tiny difference times the huge gain gives the needed output. Without feedback (a comparator), with positive feedback (a Schmitt trigger) or once the output hits a supply rail, the inputs can differ by volts.

    Why people get this wrong: Applying V+=V− to a comparator or a saturated amplifier.

  2. NATStandard

    Two inputs, 2.0 V and 4.0 V, are each connected through a 10 kΩ resistor to the non-inverting input of an ideal op-amp (nothing else connects there). The op-amp has Rf=20 kΩ from output to inverting input and R1=10 kΩ from inverting input to ground. The output is ______ V (to one decimal place).
    Answer and solution

    Answer: 9 V (±0.05)

    No current enters the non-inverting input, so the two equal resistors form a divider that averages the inputs: V+=(2.0+4.0)/2=3.0 V. The stage is a non-inverting amplifier of gain 1+Rf/R1=3, so Vout=9.0 V. This non-inverting summer gives Vout=V1+V2 when the gain equals the number of inputs.

    Why people get this wrong: Treating it like the inverting summer (adding currents into a virtual ground) gives −12 V.

  3. MCQStandard

    An ideal inverting amplifier has Rin=10 kΩ and Rf=100 kΩ. The input resistance seen by the signal source is
    1. infinite, because the op-amp draws no current
    2. zero, because of the virtual ground
    3. 10 kΩ
    4. 100 kΩ
    Answer and solution

    Answer: C

    The inverting input is held at (virtual) ground, so the source sees Rin going to ground: the input current is Vin/Rin and the input resistance is 10 kΩ. This is a weakness of the inverting stage: raising its input resistance means raising both resistors. The non-inverting stage, by contrast, has a very high input resistance.

    Why people get this wrong: "Op-amps have infinite input resistance" describes the op-amp's own terminals, not this circuit's input.

  4. NATExam level

    A unity-gain Sallen-Key low-pass filter has R1=R2=10 kΩ, C1=20 nF (from the junction of the resistors to the output) and C2=10 nF (from the non-inverting input to ground). Its natural frequency f0=12πR1R2C1C2 is ______ Hz (to the nearest whole number).
    Answer and solution

    Answer: 1125 Hz (±5)

    R1R2C1C2=(104)2(2.0×10−8)(1.0×10−8)=2.0×10−8 s2, whose square root is 1.414×10−4 s. f0=12π×1.414×10−4=1125 Hz. Its quality factor is Q=R1R2C1C2C2(R1+R2)=1.414×10−42.0×10−4=0.707: a Butterworth response, chosen by making C1=2C2.

    Why people get this wrong: Using 1/2πRC with one of the capacitors gives 796 Hz or 1592 Hz.

  5. MSQExam level

    Which statements about active filters are correct?
    1. A second-order Butterworth low-pass filter has Q=1/2.
    2. A unity-gain Sallen-Key low-pass with equal resistors and equal capacitors has Q=0.5.
    3. An active filter cannot have a pass-band gain greater than 1.
    4. A first-order low-pass filter falls off at 20 dB per decade above its cutoff.
    Answer and solution

    Answer: A, B, D

    Each pole adds −20 dB/decade, so first order gives 20 and second order 40 dB/decade. The Butterworth (maximally flat) second-order response has Q=0.707. For the unity-gain Sallen-Key, Q=R1R2C1C2C2(R1+R2)=RC2RC=0.5 with equal parts (a bit droopy; choose C1=2C2 for Butterworth). Op-amp filters can easily have gain, e.g. by setting the amplifier gain above 1; that is one of their advantages over passive RC filters.

    Why people get this wrong: Thinking "filter" means "passive": the op-amp can provide gain and a low output impedance at the same time.

  6. MCQExam level

    A non-inverting op-amp amplifier uses which kind of negative feedback, and what does it do to the input and output resistances?
    1. Series-shunt (voltage-series): it raises the input resistance and lowers the output resistance.
    2. Shunt-shunt (voltage-shunt): it lowers both the input and output resistances.
    3. Series-series (current-series): it raises both resistances.
    4. Shunt-series (current-shunt): it lowers the input resistance and raises the output resistance.
    Answer and solution

    Answer: A

    The feedback network samples the output voltage (shunt connection at the output) and returns a voltage that sits in series with the input signal, between the two op-amp inputs. Series mixing multiplies the input resistance by (1+Aβ); shunt sampling divides the output resistance by (1+Aβ). That makes it a near-ideal voltage amplifier. The inverting amplifier is the shunt-shunt case.

    Why people get this wrong: Naming the topology by the output connection only; the input mixing (series here) decides what happens to the input resistance.

  7. NATHard

    A non-inverting Schmitt trigger feeds the input through R1=10 kΩ to the non-inverting input, with R2=40 kΩ from the output back to the same input. The inverting input is held at +1.0 V, and the output saturates at ±12 V. Starting with the output low, the input must rise to ______ V before the output switches high (to two decimal places).
    Answer and solution

    Answer: 4.25 V (±0.02)

    The output flips when V+ crosses 1.0 V. By superposition V+=VinR2+VoutR1R1+R2. With Vout=−12 V: 1.0=40Vin−12050, so Vin=50+12040=4.25 V. The lower threshold (output high) is 50−12040=−1.75 V, so the hysteresis is 6.0 V wide and centred on 1.25 V, not on the 1.0 V reference.

    Why people get this wrong: Assuming the thresholds sit symmetrically about the reference (1.0±3.0 V); the reference is scaled by (R1+R2)/R2.

  8. MCQHard

    An op-amp whose open-loop response has two poles is stable as an amplifier with gain 10 but oscillates when wired as a voltage follower. The reason is that the follower
    1. draws more current from the source
    2. has positive feedback
    3. has a higher slew rate
    4. has the largest feedback fraction, β=1, so its loop gain Aβ crosses unity at a higher frequency where the phase shift is larger
    Answer and solution

    Answer: D

    Stability depends on the loop gain Aβ. A follower feeds back all of the output (β=1), the most any resistive network can, so |Aβ|=1 happens at the highest frequency, where the second pole has added the most phase lag. If the total lag there reaches 180∘ the loop oscillates. Higher-gain stages (β=0.1) cross over lower down, with more phase margin. "Unity-gain stable" op-amps are compensated for exactly this worst case.

    Why people get this wrong: Thinking low gain means "easy" for the op-amp: for stability the unity-gain follower is the hardest case.

  9. MSQHard

    An amplifier with open-loop gain A (a single pole) has negative feedback with feedback fraction β. Which statements are correct?
    1. A fractional change in A changes the closed-loop gain by that fraction divided by (1+Aβ).
    2. The bandwidth rises by the factor (1+Aβ).
    3. If the output voltage is sampled, the output resistance falls by (1+Aβ).
    4. In an inverting amplifier, the resistance looking into the op-amp's inverting-input node rises by (1+Aβ).
    Answer and solution

    Answer: A, B, C

    G=A1+Aβ gives dGG=11+AβdAA. With a single pole the gain-bandwidth product is conserved, so the bandwidth grows by (1+Aβ) as the gain falls by it. Voltage sampling divides the output resistance by (1+Aβ). At the inverting-input node the feedback resistor looks like Rf/(1+A) (Miller effect): the node is a virtual ground with very low resistance, not high.

    Why people get this wrong: Assuming feedback always raises input resistance: shunt mixing (as at the inverting input) lowers it.

  10. NATTop rank

    An op-amp relaxation oscillator (astable) charges a 10 nF capacitor through R=47 kΩ from the output (saturating at ±Vsat); the capacitor sits on the inverting input. The non-inverting input is fed from the output by a divider with R2=40 kΩ from the output and R1=10 kΩ to ground. The oscillation frequency is ______ Hz (to the nearest whole number).
    Answer and solution

    Answer: 2624 Hz (±15)

    The thresholds are ±βVsat with β=R1R1+R2=0.2. Each half cycle the capacitor heads for ±Vsat from ∓βVsat and switches at ±βVsat: β=1−(1+β)e−t/RC, so thalf=RCln⁡1+β1−β=(4.7×10−4)ln⁡1.5=1.906×10−4 s. The period is twice that, 3.81×10−4 s, so f=2624 Hz.

    Why people get this wrong: Using ln⁡3 (the result for β=0.5) or forgetting that a period has two half cycles.

← All topics · Timed mock test →